IT9001 IT9002 Cooker Hood INSTALLATION AND USER’S MANUAL Cod:0103090161-00.
SAFETY PRECAUTION • Important! Always switch off the electricity supply at the mains during installation and maintenance such as light bulb replacement. • The cooker hood must be installed in accordance with the installation instructions and all measurements followed. • All installation work must be carried out by a competent person or qualified electrician. • Please dispose of the packing material carefully. Children are vulnerable to it.
SAFETY PRECAUTION • – – – – – – – • • Caution: The appliance and its accessible parts can become hot during operation. Be careful to avoid touching the heating elements. Children younger than 8 years old should stay away unless they are under permanent supervision. There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels. There is a fire risk if cleaning is not carried out in accordance with the instructions.
Parts identification (IT9001) Parts Name 1 2 15 3 16 (1) Ducting hose (2) Hanging bracket (3) Blower (4) Motor housing (5) Motor (6) Fan (7) Air collector 4 5 17 6 78 9 18 (8) Nut (9) Maintenance cover (10) Wire protection box (11) Capacitor (12) Outer Chimney (13) Inner Chimney Bracket (14) Inner Chimney 10 11 19 12 20 21 (15) Damper (16) Main body (17) Baffle filter (18) Main body cover (19) Oil collector (20) LED lamp (21) Push button Technical specifications Model Voltage Product dime
Parts identification (IT9002) Parts Name 1 2 3 17 4 18 (1)Ducting hose (2) Hanging bracket (3) Blower (4) Motor housing (5) Motor (6) Fan (7) Air collector 5 6 78 9 19 (8) Nut (9) Maintenance cover (10) Wire protection box (11) Capacitor (12) PCB (13) Touch control box (14) Outer Chimney 10 11 12 13 20 21 14 22 23 (15) Inner Chimney Bracket (16) Inner Chimney (17) Damper (18) Main body (19) Baffle filter (20) Main body cover (21) Oil collector 15 16 24 (22) LED lamp (23) Touch control s
Using your Range hood (IT9001) For best performance, you should switch on the range hood few minutes before starting to cook and leave it to run for approximately 15 minutes after the end of cooking. Control Panel A – Power off button B – Speed level buttons C – Light button Fig. 1 C B A To switch the extractor light on or off: • Press button C.
Using your Range hood (IT9002) For best performance, you should switch on the range hood few minutes before starting to cook and leave it to run for approximately 15 minutes after the end of cooking. Control Panel A - Light key B - Speed level keys C - Off key Fig. 1 A B C To switch on the extractor or to change the speed at any time when the extractor is running: • Touch the relevant key “B” for the first, second or third speed level as required.
Filter Cleaning IMPORTANT : DO NOT PERFORM MAINTENANCE OR CLEANING OF THE RANGE HOOD WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. Oil Collector When the oil reaches maximum marked position on oil collector, clear the oil in time in case of overflow. As Fig. 2-1, pull out the oil collector horizontally to remove it. Filter Cleaning • Remove the screws to remove the filter. (Fig 2-2) • Use warm water with detergent to steep the filter for some time later, use rag to scrub the filter.
Changing the Light NOTE: LED lights replacement must be done by a qualified electrician. IMPORTANT: DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. Replace LED light Check with your local retailer or dealer to buy new same LED lights for replacement. Fig. 3-I Remove the lamp buy flat-head screwdriver. Pull out the lamp. Unplug the lamp wire connector (Fig. 3). Plug wire connector with new lamp. Put the new lamp into lamp holder.
Electrical Information Mains electrical voltage: 220Vac Total rated power consumption: 202W Troubleshooting Please note: Your Range hood is equipped with a motor protection device that will switch off the motor to prevent damage from overheating. This may happen during cooking when most or all of the zones/burners are being used simultaneously, or if your Range hood is installed incorrectly, lower than the recommended height.
Mounting your Range hood When the Range hood is to be installed above an electric hob, the minimum distance between the hob and Range hood must exceed 650mm. 550 430 When the Range hood is to be installed above a gas hob, the minimum distance between the hob and Range hood must exceed 700mm. 324 220 375 If the instructions for installation for the gas hob specify a greater distance, this has to be taken into account.
INSTALLATION Tools required Mark wall as required (see Fig. 6) 8 Fig. 5 Fig. 6 Fix support plate on the wall by screws with expanding plugs. Drill holes for mounting the body. 10mm Fig. 7 Fig. 8 Secure hood (tighten all screws). Fit ducting adaptor. Fig. 9 Fig. 10 IMPORTANT SAFETY WARNING: ONLY USE THE SCREWS PROVIDED WITH THE RANGE HOOD TO MOUNT THE DUCTING ADAPTOR. THE USE OF LONGER SCREWS MAY CAUSE DAMAGE TO THE INTERNAL WIRING WHICH WILL NOT BE COVERED BY THE WARRANTY.
INSTALLATION Fix ducting (seal joint by 3 pieces ST3X8). Fig. 11 Install end cap. 180mm 175mm 550mm 650mm~700mm Fig.
Information for cooker hood ENVIRONMENTAL PROTECTION: This product is marked with the symbol on the selective sorting of waste electronic equipment. This means that this product must not be disposed of with household waste but must be supported by a system of selective collection in accordance with Directive 2002/96/EC.
