LCD TV OWNER`S MANUAL MODEL S : L26A9A L32A9A L37A9A Please READ this manual carefully before operating your TV, and retain it for future reference. PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.
Warning Safety of operators has been taken into consideration at the design and manufacture phase, but inappropriate operation may cause electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of th product. Read the following safety instruction before starting the operation.
Important Safety Instructions Important safeguards for you and your new product Your product has been manufactured and tested with your safety in mind. However, improper use can result in electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference. 1.
Important Safety Instructions a. When the power supply cord or plug is damaged or frayed. b. If liquid has been spilled, or objects have been fallen into the unit. c. If the unit has been exposed to rain or water. d. If the unit does not operate normally by following the operating instructions.
Table of Contents Warning .............................................1 Important Safety Instructions................2 Buttons and interface location..............5 Front control panel............................5 Rear control panel.............................6 Remote controller................................7 Keys of remote controller......................8 Function introduction ........................8 Effective range .................................9 External Equipment Connections ........
Buttons and interface location -This is a simplified representation of front panel. -Here shown may be somewhat different from your TV. Front control panel L26A9A,L32A9A TV/AV MENU VOLVOL+ CHCH+ POWER 5 4 3 2 1 6 7 L37A9A 1. Power 2.CH- /CH+ Program plus and minus, menu options 3.VOL-/VOL+ Volume increase and decrease, menu reset and entry4. 4.MENU Menu display 5.TV/AV: Source input select 6. Remote control signal receive window. 7.Remote Indicator In red when standby mode, in blue when Display.
Buttons and interface location Rear Control panel AUDIO VIDEO DVD/DTV Input (Component ) Connect a component video/audiodevice to these jacks. PC VIDEO Input Connect the monitor output connector from a PC to the jack VG A IN V GA AUDIO CO MPO NENT IN P r/Cr Pb /Cb Y L-A UDIO-R SCART2/SCART1 Input (Canal+) Connect Scart out from an Scart device to the Scart input. Antenna Input Connect cable or antenna signals to the TV, either directly or through your cable box.
Remote controller
MUTE STILL SCAN SLEEP PIP ABC@ DISPLAY DEF GHI$ JKL% MNO POR& STUV WXYZ TV/AV *#() SWAP P.STD S.STD CH+ VOL- VOL+ CH- H.LOCK CH.
Remote controller Ensure the remote controller is pointed toward the remote controller window on the display. No obstacles should be placed between the remote controller and the remote controller window. The effective receiving scope for the signal is 8 meters to the O front of the remote controller window, and 45 to the left or right O side and 20 above or below the control window. Use of remote controller: 1.
External Equipment Connections Generally speaking, to enjoy a clearer picture, we recommend that you use a CATV system or an outdoor antenna .In different places, the suitable antenna type and position are different.
External Equipment Connection NOTE: All cables shown are not included with the TV. Choose Your Connection There are several ways to connect your television, depending on the components you want to connect and the quality of the signal you want to achieve. The following are examples of some ways to connect your TV. Choose the connection which is best for you. VCR connection - To avoid picture noise (interference), leave an adequate distance between the VCR And TV. 1.
External Equipment Connections DVD connection How to connect 1. Connect the DVD video outputs (Y, Pb/Cb, Pr/Cr) to the YUV IN jacks on the TV and connect the DVD audio outputs to the AUDIO IN jacks on the TV, as shown in the figure. COMPO NENT IN 2 . If your DVD only has an SCART output Pr /Cr Pb/Cb Y SCART 2 L-AUDIO -R S CART1 ANT IN jack, connect this to the SCART input on the TV. as shown in the figure. NOTE: If your DVD player does not have component video output, use S-Video.
External Equipment Connections PC connection How to connect or DVI source. 1 . To get the best picture quality, adjust the PC 4 . Check the image on your TV. There may graphics card to ( >1024x768),60Hz. 2 . Use the TV`s VGA IN port for video connections, depending on your PC connector. If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of eitherVGA IN to display the PC on the TV.
External Equipment Connections Connecting Headphones You can connect a set of headphones to your set if you wish to watch a TV programme without disturbing the other people in the room. Plug a set of headphones into the 3.5mm mini-jack socket on the rear panel of the set. Note ANT IN SWITCH AC-INPUT Prolonged use of headphones at a high volume may damage your hearing. You will not receive sound from the speakers when you connect headphones to the system.
Set up your TV -There are several options you might need to set up in order for your TV to work properly. Read the instructions that follow. -In the manual, the OSD(on screen display) may be different from your TV`s, because it is just an example to help you with the TV operation. Switching ON/OFF the TV set 1 Please press down the power switch to switch on AC power supply and the power indicator will light . 2 If the indicator is lighting in red, press button on the remote controller again.
MUTE STILL SCAN SLEEP PIP ABC@ DISPLAY DEF GHI$ JKL% MNO POR& STUV WXYZ TV/AV *#() SWAP P.STD S.STD H.LOCK CH.
Tuning menu This TV set has three methods to set channels, which are respectively full automatic, manual search fine tune. In this section, how to use the remote control to set channel is explained. You can also use buttons on the TV set to set channel.
Tuning menu Program Table
Tuning menu Manual search If excessive channel signals of unwanted programs are received in local area, manual search function is recommended. 1 Press CH+/- buttons or the NUMBER 0-9 button to choose desired searching frequency. (regard channel 18 as example). 2 After calling up the TU NING menu, press CH+/- button to select "Tuning Program" item. 3 Press CH+/- to select Manual Search item, Press VOL+ button to enter the desired frequency and press the digital button to adjust.
MUTE STILL SCAN SLEEP PIP ABC@ DISPLAY DEF GHI$ JKL% MNO POR& STUV WXYZ TV/AV *#() SWAP P.STD S.STD CH+ VOL- VOL+ CH- H.LOCK CH.
Tuning menu You can watch TV program in a presetting channel. How to select the desired program 1 Using "Program number" buttons MUTE STILL SCAN SLEEP PIP ABC@ DISPLAY DEF GHI$ JKL% MN O POR& STUV WXYZ TV/AV *#() SWAP P.STD Press digit button to select the program. If 2-digit or 3-digit programs are selected , press digit buttons you needed continuously within 3 seconds .
Tuning menu If the colour of some channel is abnormal Usually this should be set in the auto position. However if the colour displayed on the screen are incorrect, you can manually select the correct colour system. MUTE STIL L SCAN SLEEP PIP ABC@ GHI$ JKL% DISPLAY DEF Press the MENU CH+/-and VOL+/- button, till the Tuning Program menu shown on the right will display on the screen.
Tuning menu Skip After the programs are presetting, you can skip some programs so that to select your favorite channels only. 1 . Press CH+/- button or MUTE STILL SCAN SLEEP PIP ABC@ GHI$ POR& TV/AV JKL% STUV *#() DISPLAY DEF WXYZ S.STD CH+ VOL- MENU VOL+ MENU PICTURE AUDIO 2 .Press MENU MNO SWAP P.STD Direct-digit Choosing button to select a channel directly (take channel 18 for example).
Picture menu How to select picture modes You can quickly select the desired picture mode from three preset modes and one customized mode. MUTE STILL SCAN SLEEP PIP ABC@ DISPLAY DEF GHI$ JKL% MNO POR& STUV WXYZ TV/AV *#() SWAP P.STD S.STD Press the P.STD button to call up Video mode menu, and press CH+/-button to select the desired picture quality. Four kinds of picture modes (i.e., "Normal", "Soft", "Personal" , "Bright", ) can be selected in turn.
Picture menu Noise Reduction Automatically filters out and reduces the image noise and improves picture quality when receiving weak video signals. MUTE STILL SCAN SLEEP PIP ABC@ DISPLAY DEF GHI$ JKL% MNO POR& STUV WXYZ 1 After calling up the Picture menu, press CH+/- button to select "Noise Reduction" item. MENU PICTURE TV/AV *#() SWAP P.STD S.STD CH+ VOL- MENU VOL+ 2 Press VOL+ to enter AUDIO the list. Select Auto, Off Weak , M edium or Strong according to the image noise.
To choose sound modes
Setting Five Equalizer sound The sound settings can be adjusted to suit your personal preferences. 1 Press MENU button and then CH+/- button to select AUDIO menu. MUTE STILL SCAN SLEEP PIP ABC@ DISPLAY DEF GHI$ JKL% MNO POR& STUV WXYZ TV/AV *#() to select "Five Equalizer", then press VOL+ buttons to enter the submenu. SWAP P.STD S.
Sound menu Setting the Auto Volume Each broadcasting station has its own signal conditions, and so it is not easy for you to adjust the volume every time the channel is changed. This feature lets you automatically adjust the volume of the desired channel and reduces the volume differences between channels and programs, providing a more constant overall level. This will also reduce the dynamics of sound. Repeated step 1-2, and press CH+/- to select Auto Volume , and then press VOL+/- to set as Off or On.
Timer menu Timer setting The clock will only work if the TV set is turned on or in standby. When the set is disconnect from the power supply or is turned off by the main power on the rear panel, the clock loses power and will need to be reset when the power MUTE STILL SCAN SLEEP PIP ABC@ DISPLAY DEF GHI$ JKL% MNO POR& STUV WXYZ TV/AV *#() 1 Press the MENU button and CH+/- button, till the TIMER menu display on the screen. SWAP P.STD MENU S.
Timer menu You can set the On/Off timers so that the set will : Switch on automatically and tune to the channel of your choice at the time you select. Switch off automatically at the time you select. On/off timer \Timer on Prog\ Timer Prog 1 Press MENU and VOL+/- button to call up the TIMER menu on the screen. MUTE STIL L SCAN SLEEP PIP ABC@ MENU DISPLAY PICTURE DEF AUDIO GHI$ JKL% MNO POR& STUV WXYZ ADJUST TUNING FUNCTION TV/AV *#() P.STD S.
Function menu It is possible to select language, OSD transparent, position and screen display of the menu as follows: Function setup 1 . Press MENU button once, and the CH+/- button until the following menu appears on the screen: MENU MUTE STILL SCAN SLEEP PIP DISPLAY PICTURE AUDIO ABC@ DEF ADJUST TUNING GHI$ JKL% MNO POR& STUV WXYZ FUNCTION TV/AV *#() English 15 seconds Transparent Off West Europe SWAP P.STD S.STD MENU 2 .
Function menu Function setup (continue) Calendar display and check Repeat step 3 and 4 to enter Calendar menu as follows: 2005-01-01 Sun. Mon. Tue. Wed. Thu. Fri. Sat. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Press VOL+/- to select among year, month and day, and then CH+/- to adjust them. TeleText Language Repeat step 3 and 4 to select from 6 kinds of languages. (West Europe/East Europe/Cyrillic/Greek/Arabic/Persian.
Adjust menu To choose picture aspect ratio 1 Using ZOOM button. Press ZOOM button to select the desired picture ratio. Three kinds of aspect ratio models (i.e., " Normal " , " Wide Screen" and " 4:3 Mode " ) can be selected in turn. Normal Wide Screen 4:3 Mode 2 Using the MENU button. 1 Press MENU button and then CH+/- button , till the ADJUST menu shown on the right display on the screen. MENU PICTURE AUDIO Note: Under the HDTV VGA and HDMI signal, there are only Normal and 4:3 mode to adjust.
Adjust menu In PC input mode, H-Position and V-Position can be adjusted to eliminate transverse line interference and decentered picture as follows: H-Position and V-Position adjust Adjust is opted for adjusting H-Position and V-Position as well as relative parameters in VGA and HDMI modes. 1. Press MENU button and CH+/- to call up the ADJUST menu.
Adjust menu RGB/Default/Auto Sync 1) RGB is opted for adjustment of the numerical value of red, green and blue in VGA,HDMI mode. 2) Default is opted for adjustment of parameters to delivery setup in PC mode.(After the operation, complete will be on the right of the operation) 3) Auto Sync is opted for adjustment of picture location frequency and phase parameters in VGA mode.
Lock setup How to use the password function The television has the function of security default lock. Password needs to be entered when the program lock mode is to be set. Press H.LOCK button, Password will appear on the screen. The initial password of the television is 0000 and security default password is 9443. then enter Lock Set menu.
Lock setup Tuner Lock Press CH+/- to select Tuner Lock and VOL+/- to set On/ Off. (To set On, some operation such as search will be not available. When enter the TUNING menu, Tuner Lock will be on the screen, and the time will be the same with the main menu if no operation. If you want to operate TUNING menu, you need to enter the Lock menu to set Tuner Lock Off or operate Clear Lock. MUTE STILL SCAN SLEEP PIP ABC@ DISPLAY DEF GHI$ JKL% MNO POR& STUV WXYZ TV/AV *#() SWAP P.
Lock setup Child Lock MUTE STILL SCAN SLEEP PIP ABC@ DISPLAY DEF GHI$ JKL% MNO POR& STUV WXYZ TV/AV *#() Press CH+/- button to select Child Lock. Press VOL+/- button to set On or Off mode. If lock on mode is set, Child Lock is in activated automatically. In such case, if Child Lock button (button on the television) is pressed, the screen will display Child Lock, which can be erased by press of EXIT button.
Others functions NICAM If the broadcaster is transmitting Bilingual sound service. The / button on the remote controller will allow up to 2 separate languages to be selected. You can press the / button to make a choice. Display function If current program number, color system and sound system are to be displayed on the screen, press DISPLAY button, and all the related information will appear at right up corner of the screen. If the DISPLAY button is pressed again, the displayed information will disappear.
Others functions Sleep Note: The Time On setup and the SLEEP setup is absolute one another. The TV set will switch automatically to standby at the preset time with the SLEEP time on. You may set the sleep time, Operate as follows: 1. Press SLEEP button repeatedly to select the number of preset minutes, the timer will be set in sequence: 0Min 5Min 15Min 30Min 60Min 90Min 120Min 0Min 2 .
Teletext functions Teletext is an information system, broadcast by certain channels, which can be read like a newspaper . It also provides subtitles for people with hearing difficulties or those who are unfamiliar with the language in which a particular programme is being broadcast (cable networks, satellite channels, etc.). Teletext function operation MUTE STILL SCAN SLEEP PIP ABC@ DISPLAY DEF GHI$ JKL% MNO POR& STUV WXYZ TV/AV *#() SWAP P.
Teletext functions (MIX) While in Teletext mode press the button will show the teletext data superimposed on top of the TV picture. Press the button again to revert back to Full text. (HOLD) Pressing the button will stop the teletext page automatically updating. This feature is very useful where there are several teletext pages or data on the same page number. (SIZE) Pressing the button to change from different screen display size.
Maintenance - Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen 1 . Here`s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it`s almost dry, and then use it to wipe the screen. 2 .
Specifications and functions L32A9A L26A9A 1366X768(Dot) 1366X768(Dot) L37A9A 1366X768(Dot) ~100-240V , 50/60Hz PAL, SECAM, NTSC 75 ohm External Antenna Impedance 5 20% Storage Temperature Size (WxD xH) unit: mm main component Net Weight(Kg) 80% -10 Storage Humidity Model 35 5% L26A9A 679 246 45 90%, non-condensing L32A9A 525 12.5kg 811 246 621 16kg PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.
Troubleshooting For the sake of time and cost, it is strongly recommended that you check out the problem by yourself according to the instructions listed hereunder before contacting the after-sales service for technical assistance. No picture, no sound Verify if the television is properly plugged. Verify if the television is properly supplied power. Verify if electricity is available. Blank screen Verify if correct signals are input. Press TV/AV button to change signal input to TV input.
0090506971H 01 PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.
