Phau Ntawv Qhia

ManualsBrandshais tias ManualsSurface Microsignify ID-TM11 TruGroove Surface Micro

Rev B. www.ledalite.compage6/9/2022 1

Architectural Linear

IS-TM11 Surface Direct

TruGroove surface micro

System Overview

These instructions review how to install TruGroove surface micro fixtures. Modules can be installed as

individual 2ft, 2.5ft, 3ft, 3.5ft, 4ft, 5ft, 6ft or 8ft standalone units, or they can be joined together to

create continuous runs. IMPORTANT: Read all instructions before beginning installation. All ceiling

brackets must be secured to ceiling structure (studs or cross-braces). Power feed connections for

TruGroove surface micro modules can be made through a recessed 2”X4” utility box (by others) or

with a surface mounted junction box/exposed conduit (by others).

TOOLS REQUIRED:

• Phillips screwdriver

• Flat-head

screwdriver

• #2 Robertson

screwdriver

(optional)

• small ratchet

• Ø7/8 drill bit

TM Surface Endcap Kit

• TM Surface Endcap (x1)

• #8-32 x 5/16” screw (x2)

• 1ft A/C cable (x1)

• TM Surf Ceiling Bracket (x1)

*Note: 2 kits required for

capped ends

TM Surface Joint Kit

• TM joiner aligner pair (x2)

• TM Surface Ceiling Bracket (x2)

• #10-32 x 3/4” screw (x2)

• #10-32 nut (x2)

• 1ft A/C cable (x2)

*Note: 1 kit required for each joint

ATTENTION: Install in accordance with local and national building and electric codes.

Module Lengths

TruGroove surface micro

fixtures come in the

module lengths shown.

Add 0.25” for each endcap

for accurate run length.

Length

without

endcaps

feet

2.0 2.5 3.0 3.5 4.0 5.0 6.0 8.0

Inches

24.0 30.0 36.0 42.0 48.0 60.0 72.0 96.0

mm 610 762 914 1067 1219 1524 1829 2438

Housing Length

Summary of content (10 pages)

PAGE 1
Architectural Linear TruGroove surface micro IS-TM11 Surface Direct System Overview These instructions review how to install TruGroove surface micro fixtures. Modules can be installed as individual 2ft, 2.5ft, 3ft, 3.5ft, 4ft, 5ft, 6ft or 8ft standalone units, or they can be joined together to create continuous runs. IMPORTANT: Read all instructions before beginning installation. All ceiling brackets must be secured to ceiling structure (studs or cross-braces).
PAGE 2
IS-TM11 Surface Mount Installation Instructions This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interreference when the equipment is operated in a commercial environment.
PAGE 3
IS-TM11 Surface Mount Installation Instructions Lens Removal 1a Lens Removal 1b Symmetric Fixture 1c Asymmetric Fixture Direction of light Lens Removal: To remove snap-in lens for maintenance purposes, insert a flat, smooth edged object between lens and housing (avoid screwdrivers). Twist to release pressure and remove lens. 1d Remove lens from fixture and set aside until fixture installation is complete. Use cotton gloves to handle lenses and keep in a clean environment.
PAGE 4
IS-TM11 Surface Mount Installation Instructions 3 Recessed Utility Box 4 Surface Junction Box 5 Recessed Power Feed Location Power entry cover Align center of recessed utility box with the center of the ceiling bracket Align center of surface mounted junction box with the center of the ceiling bracket For a recessed 2”X4” utility box, align and center with ceiling brackets, and install with long edge parallel with fixture module length.
PAGE 5
IS-TM11 Surface Mount Installation Instructions 9a Surface Power Feed Preparation 9b Surface Power Feed Connection Supplied by others Center mark for drilling operation For surface junction box installation, power feed to fixture module is done through the endcap. Use masking tape on all outside surfaces. Align with center mark as shown and drill a 7/8” diameter hole.
PAGE 6
IS-TM11 Surface Mount Installation Instructions 13 Fixture Joining 12 Fixture Joining Small Joiner Aligners Module 1 Module 2 Large Joiner Aligners Bring module 1 and 2 together. Engage joiner aligners in module 2 with housing of module 1. Ensure all connections are secure and all wires are neatly tucked inside fixture wiring cavity. Slide fixture modules together gently.
PAGE 7
IS-TM11 Surface Mount Installation Instructions 17 Endcap with Sensor 18 Endcap Installation Before installing the endcap, slide the sensor towards the center of the fixture to gain access. Proceed with endcap installation, step 18. 20 Closed Pattern Installation Slide endcap onto end of fixture module and secure from below using two #8-32 X 5/16” screws. Tighten screws until endcap seam is tight. Note: Do not overtighten.
PAGE 8
IS-TM11 22b Surface Mount Installation Instructions Fixture Lens Installation 23 24 Louver Installation Corner Lens Installation Fully installed Once lens is positioned inside housing, starting on one end or joint, push upwards gently and work outward to complete the run. Reinstall surface plates with the screws provided and follow with louvers. Start on one end of the louver pressing gently on side tabs.
PAGE 9
IS-TM11 Surface Mount Installation Instructions Sensors in Rows Single Sensor Controlling Whole Row 1. Purple & brown (or purple & grey/pink) control wires MUST be connected between fixtures. Note: • A maximum of 8 drivers can be wired to one sensor; confirm fixture driver count with factory. 1 Integral Sensor Alternate Remote Sensor Bottom view of fixtures 4ft 8ft Multiple Sensors Controlling Separate Zones in a Row 2.
PAGE 10
IS-TM11 Surface Mount Installation Instructions Occupancy Sensor Coverage: Note: Longer dimension of detection area (Y1, Y2) is parallel to longer dimension of the luminaire. The detection area for the movement sensor can be roughly divided into two parts: • Minor movement (person moving ≤3ft/s or 0.9m/s). • Major movement (person moving ≥3ft/s or 0.9m/s).