Installation Guide

ProLED
®
Select Volumetric Panel
Install Instructions
®
© 2020 Halco Lighting Technologies, LLC. All rights reserved. Halco is a registered trademark of Halco Lighting Technologies. All sizes and specications are subject to change.
Halco Lighting Technologies | 2940 Pacic Drive | Norcross, GA 30071 | Toll Free 800.677.3334 | Phone [phone] | Fax [phone] | halcolighting.com | Atlanta | Chicago | Cleveland | Houston | Los Angeles | Phoenix
`
Field Adjustable & CCT Tunable Troffer Series Installation Guide
SAFETY INSTRUCTIONS: Read instructions carefully before attempting to install fixture.
 All wiring should be performed by a qualified electrician.
 Disconnect power before installing or servicing. This fixture must be wired in accordance with the National Electrical
Code and applicable local codes and ordinances.
 CAUTION: Do NOT use this product for other than intended use. To prevent early product failure, luminaire should
only be used in operating environments ranging from -20°C (-4°F) to 40°C (104°F).
 All wiring is recommended to be capped with UL approved wire connectors.
 CAUTION: Wear gloves and safety goggles always when removing luminaire from carton, installing, servicing or
performing maintenance.
 Avoid direct eye exposure to the light source while it is on.
 Account for small parts and dispose packing material as these may be hazardous to children.
CAUTION: Risk of fire
 WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
 WARNING: Turn off electrical power at fuse or circuit breaker box before wiring the luminaire to the power supply.
 WARNING: Verify that the voltage is correct by comparing it with the luminaire label information.
 WARNING: Keep combustible and other materials that can burn away from luminaire.
 WARNING: Minimum 90°C supply conductors.
CLEANING & MAINTENANCE:
CAUTION: Be sure the fixture temperature is cool enough to touch. Do NOT clean or maintain while the fixture is energized.
1. Clean glass lens with non-abrasive glass cleaning solution.
2. Do NOT open fixture to clean the LED. Do NOT touch the LED.
Note: These instructions do not cover all details or variation in equipment, nor do they provide for every possible situation during
installation, operation or maintenance.
TROUBLESHOOTING:
1. Check that the line voltage at fixture is correct. Refer to wiring directions.
2. Be sure the fixture is grounded properly.
OPERATING CHARACTERISTIC:
 Voltage Input: 120-277V 50/60Hz
 Operating Temperature: -20°C (-4°F) to 40°C (104°F)
WATTAGE & COLOR TEMPERATURE SELECTION:
、
1x4 and 2x2
`
Field Adjustable & CCT Tunable Troffer Series Installation Guide
SAFETY INSTRUCTIONS: Read instructions carefully before attempting to install fixture.
 All wiring should be performed by a qualified electrician.

Disconnect power before installing or servicing. This fixture must be wired in accordance with the National Electrical
Code and applicable local codes and ordinances.
 CAUTION:
Do NOT use this product for other than intended use. To prevent early product failure, luminaire should
only be used in operating environments ranging from -20°C (-4°F) to 40°C (104°F).
 All wiring is recommended to be capped with UL approved wire connectors.
 CAUTION: Wear gloves and safety goggles always when removing luminaire from carton, installing, servicing or
performing maintenance.
 Avoid direct eye exposure to the light source while it is on.
 Account for small parts and dispose packing material as these may be hazardous to children.
CAUTION: Risk of fire
 WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
 WARNING:
Turn off electrical power at fuse or circuit breaker box before wiring the luminaire to the power supply.
 WARNING: Verify that the voltage is correct by comparing it with the luminaire label information.
 WARNING: Keep combustible and other materials that can burn away from luminaire.
 WARNING: Minimum 90°C supply conductors.
CLEANING & MAINTENANCE:
CAUTION: Be sure the fixture temperature is cool enough to touch. Do NOT clean or maintain while the fixture is energized.
1. Clean glass lens with non-abrasive glass cleaning solution.
2. Do NOT open fixture to clean the LED. Do NOT touch the LED.
Note: These instructions do not cover all details or variation in equipment, nor do they provide for every possible situation during
installation, operation or maintenance.
TROUBLESHOOTING:
1. Check that the line voltage at fixture is correct. Refer to wiring directions.
2. Be sure the fixture is grounded properly.
OPERATING CHARACTERISTIC:
 Voltage Input: 120-277V 50/60Hz
 Operating Temperature: -20°C (-4°F) to 40°C (104°F)
WATTAGE & COLOR TEMPERATURE SELECTION:
、
1x4 and 2x2
`
Field Adjustable & CCT Tunable Troffer Series Installation Guide
SAFETY INSTRUCTIONS: Read instructions carefully before attempting to install fixture.
 All wiring should be performed by a qualified electrician.
 Disconnect power before installing or servicing. This fixture must be wired in accordance with the National Electrical
Code and applicable local codes and ordinances.
 CAUTION: Do NOT use this product for other than intended use. To prevent early product failure, luminaire should
only be used in operating environments ranging from -20°C (-4°F) to 40°C (104°F).
 All wiring is recommended to be capped with UL approved wire connectors.
 CAUTION: Wear gloves and safety goggles always when removing luminaire from carton, installing, servicing or
performing maintenance.
 Avoid direct eye exposure to the light source while it is on.
 Account for small parts and dispose packing material as these may be hazardous to children.
CAUTION: Risk of fire
 WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
 WARNING: Turn off electrical power at fuse or circuit breaker box before wiring the luminaire to the power supply.
 WARNING: Verify that the voltage is correct by comparing it with the luminaire label information.
 WARNING: Keep combustible and other materials that can burn away from luminaire.
 WARNING: Minimum 90°C supply conductors.
CLEANING & MAINTENANCE:
CAUTION: Be sure the fixture temperature is cool enough to touch. Do NOT clean or maintain while the fixture is energized.
1. Clean glass lens with non-abrasive glass cleaning solution.
2. Do NOT open fixture to clean the LED. Do NOT touch the LED.
Note: These instructions do not cover all details or variation in equipment, nor do they provide for every possible situation during
installation, operation or maintenance.
TROUBLESHOOTING:
1. Check that the line voltage at fixture is correct. Refer to wiring directions.
2. Be sure the fixture is grounded properly.
OPERATING CHARACTERISTIC:
 Voltage Input: 120-277V 50/60Hz
 Operating Temperature: -20°C (-4°F) to 40°C (104°F)
WATTAGE & COLOR TEMPERATURE SELECTION:
、
1x4 and 2x2
`
Field Adjustable & CCT Tunable Troffer Series Installation Guide
SAFETY INSTRUCTIONS: Read instructions carefully before attempting to install fixture.
 All wiring should be performed by a qualified electrician.
 Disconnect power before installing or servicing. This fixture must be wired in accordance with the National Electrical
Code and applicable local codes and ordinances.
 CAUTION: Do NOT use this product for other than intended use. To prevent early product failure, luminaire should
only be used in operating environments ranging from -20°C (-4°F) to 40°C (104°F).
 All wiring is recommended to be capped with UL approved wire connectors.
 CAUTION: Wear gloves and safety goggles always when removing luminaire from carton, installing, servicing or
performing maintenance.
 Avoid direct eye exposure to the light source while it is on.
 Account for small parts and dispose packing material as these may be hazardous to children.
CAUTION: Risk of fire
 WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
 WARNING: Turn off electrical power at fuse or circuit breaker box before wiring the luminaire to the power supply.
 WARNING: Verify that the voltage is correct by comparing it with the luminaire label information.
 WARNING: Keep combustible and other materials that can burn away from luminaire.
 WARNING: Minimum 90°C supply conductors.
CLEANING & MAINTENANCE:
CAUTION: Be sure the fixture temperature is cool enough to touch. Do NOT clean or maintain while the fixture is energized.
1. Clean glass lens with non-abrasive glass cleaning solution.
2. Do NOT open fixture to clean the LED. Do NOT touch the LED.
Note: These instructions do not cover all details or variation in equipment, nor do they provide for every possible situation during
installation, operation or maintenance.
TROUBLESHOOTING:
1. Check that the line voltage at fixture is correct. Refer to wiring directions.
2. Be sure the fixture is grounded properly.
OPERATING CHARACTERISTIC:
 Voltage Input: 120-277V 50/60Hz
 Operating Temperature: -20°C (-4°F) to 40°C (104°F)
WATTAGE & COLOR TEMPERATURE SELECTION:
、
1x4 and 2x2