Manualshelf

Instructions / Assembly

ManualsBrandsHalco Lighting Technologies ManualsLightingProLED Downlight 40-Watt 10 in. 3000K Color Temperature Silver Dimmable Remodel Recessed Integrated LED Kit
12
© 2017 Halco Lighting Technologies, LLC. All rights reserved. Halco and ProLED are registered trademarks of Halco Lighting Technologies. All sizes and specications are subject to change. 07-19-17.
Halco Lighting Technologies | 2940 Pacic Drive | Norcross, GA 30071 | Toll Free 800.677.3334 | Phone 770.242.3612 | Fax 800.880.0822 | halcolighting.com | Atlanta | Carlstadt | Chicago | Cleveland | Houston | Phoenix
ProLED
®
8" and 10" LED Commercial Downlight High Performance
Installation Instructions
IMPORTANT
READ INSTRUCTIONS CAREFULLY BEFORE INSTALLING. KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PROLED LUMINAIRES MUST BE WIRED IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE AND ALL APPLICABLE LOCAL CODES.
PROPER GROUNDING IS REQUIRED FOR SAFETY. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A QUALIFIED ELECTRICIAN WHO IS FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED.
WARNING - Risk of re or electric shock. ProLED Downlight Series installation requires knowledge of the luminaires’ electrical systems. If not qualied,
DO NOT attempt installation. Contact a qualied electrician.
WARNING - Risk of re or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photographs
and/or drawings. Luminaires wiring, power supply, or other electrical parts may be damaged when drilling for installation of retrot assembly
hardware. Inspect wiring and components for damage. DO NOT make or alter any open holes in an enclosure of wiring or electrical
components during kit installation.
WARNING - To prevent wiring damage or abrasion, DO NOT expose wiring to edges of sheet metal or other sharp objects.
WARNING - Risk of re or electric shock. DO NOT alter, relocate, or remove wiring, lamp holders, power supply, or any other electrical component.
WARNING - Install this kit only in the luminaires that has the construction features and dimensions shown in the photographs and/or drawings and
where the input rating of the retrot kit does not exceed the input rating of the luminaire.
WARNING - This device is not intended for use with emergency exits.
WARNING - Risk of re or electric shock. The electrical rating of these products are 110-277 Vac, the installer must determine whether they have 100-
120Vac at the luminaire before installation.
DANGER - RISK OF SHOCK-DISCONNECT POWER BEFORE INSTALLATION
CAUTION: To avoid possible electrical shock, be sure that power supply is turned off at fuse box or circuit breaker before installing or servicing
luminaire. For your safety, read and understand instructions completely before beginning installation.
WARRANTY INFORMATION:
This product is warranted for 5 years from the date of purchase. If this product does not perform to the specications supplied on this package, send
an email or write to the address below for product return and replacement. This replacement is the sole remedy available. Liability for incidental or
consequential damage is expressly excluded. Visit www.halcolighting.com for full warranty details and dimmer compatibility information.
Please read arefully and save these instructions, as you may need them at a later date.
®
Product Code Input voltage (VAC) Input current (Ampere2) Input wattage(Watts)
CDLH8AR30/8XX/LED 110-277V AC 0.25A 30W
CDLH8AR40/8XX/LED 110-277V AC 0.33A 40W
CDLH10AR30/8XX/LED 110-277V AC 0.25A 30W
CDLH10AR40/8XX/LED 110-277V AC 0.33A 40W
XX= Designates CCT (27=2700K, 30=3000K, 40=4000K, 50=5000K)
1. Suitable for use in open, non-ic recessed housings.(FIGURE 1)
2. Suitable for dry, damp locations.
3. 0-10V dimming (10-100%)
4. Only models designated with emergency drivers (EM), are intended for use with emergency exits.
5. To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
6. TURN OFF THE POWER AT CIRCUIT BREAKER PRIOR TO INSTALLATION.
7. Remove existing trim, and existing lamp(s).
8. When running the supply wires, allow for additional 18 inch of wire at each installation in order to make the electrical connections on the room
side of the ceiling hole.
9. Attach trim mounting clips (FIGURES 2-6)
10. Insert Downlight Reector until ush with ceiling. (FIGURES 2-8)

Summary of content (2 pages)