Instructions / Assembly

Halco Lighting Technologies | 2940 Pacic Drive | Norcross, GA 30071 | Toll Free 800.677.3334 | Phone [phone] | Fax [phone] | halcolighting.com | Atlanta | Chicago | Cleveland | Houston | Los Angeles | Phoenix
®
© 2019 Halco Lighting Technologies, LLC. All rights reserved. Halco is a registered trademark of Halco Lighting Technologies. All sizes and specications are subject to change.
Please read the below articles carefully to see how to use this product safely.
Warning contents and attention contents related to product safety use, please be sure to follow it.
I
N
S
T
A
L
L
A
T
I
O
N
G
U
I
D
E
LED HID REPLACEMENT LAMP INSTALLATION GUIDE
Caution-IF THE LAMP OR LUMINAIRE EXHIBITS UNDESIRABLE OPERATION (BUZZING, FLICKERING, ETC), IMMEDIATELY TURN OFF
POWER , REMOVE LAMP FROM LUMINAIRE AND CONTACT THE MANUFACTURER OR DISTRIBUTOR.
WARNING - Follow the installation instructions to install correctly.
• Disconnect power at the source before installation, inspection or removal. Do not simply switch off fixture.
• This item is rated at 120-277VAC/100-240VAC. Installer must determine whether line voltage 120-277VAC/100-240VAC is available at
the luminaire before installation.
• Not intended for use with emergency exit fixtures or emergency exit lights.
• Not for use with luminaire ballast.
• Do not use if product is damaged.
• This lamp is non-dimmable. Not for use with dimmer.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• Risk of fire or electric shock. Do not open or modify. No user serviceable parts inside.
• Installers should not disconnect existing wires from lamp holder terminals to make new connections at lamp holder terminals. Instead
installers should cut existing lamp holder leads away from the lamp holder and make new electrical connections to lamp holder lead wires
by employing applicable connections.
• Suitable for damp locations. Suitable for use in wet locations when used in
an outdoor -rated fixture. Not for use where directly exposed to
the weather or water
• Complies with part 15 of FCC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference , and
(2) This device must accept any interference received including interference that may cause undesired operation.
• No external weight or mechanical force should be applied to lamp or components.
• THE RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION
SHALL BE DETERMINED BY UL OR AUTHORITIES HAVING JURISDICTION.
BEFORE YOU BEGIN
READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY. TO AVOID PERSONAL INJURY AND /OR PRODUCT
DAMAGE. ALL OF THE INSTRUCTIONS BELOW MUST BE FOLLOWED.
1
I
N
S
T
A
L
L
A
T
I
O
N
G
U
I
D
E
LED HID REPLACEMENT LAMP INSTALLATION GUIDE
Caution-IF THE LAMP OR LUMINAIRE EXHIBITS UNDESIRABLE OPERATION (BUZZING, FLICKERING, ETC), IMMEDIATELY TURN OFF
POWER , REMOVE LAMP FROM LUMINAIRE AND CONTACT THE MANUFACTURER OR DISTRIBUTOR.
WARNING - Follow the installation instructions to install correctly.
• Disconnect power at the source before installation, inspection or removal. Do not simply switch off fixture.
• This item is rated at 120-277VAC/100-240VAC. Installer must determine whether line voltage 120-277VAC/100-240VAC is available at
the luminaire before installation.
• Not intended for use with emergency exit fixtures or emergency exit lights.
• Not for use with luminaire ballast.
• Do not use if product is damaged.
• This lamp is non-dimmable. Not for use with dimmer.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• Risk of fire or electric shock. Do not open or modify. No user serviceable parts inside.
• Installers should not disconnect existing wires from lamp holder terminals to make new connections at lamp holder terminals. Instead
installers should cut existing lamp holder leads away from the lamp holder and make new electrical connections to lamp holder lead wires
by employing applicable connections.
• Suitable for damp locations. Suitable for use in wet locations when used in a
n outdoor -rated fixture. Not for use where directly exposed to
the weather or water
• Complies with part 15 of FCC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference , and
(2) This device must accept any interference received including interference that may cause undesired operation.
• No external weight or mechanical force should be applied to lamp or components.
• THE RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION
SHALL BE DETERMINED BY UL OR AUTHORITIES HAVING JURISDICTION.
BEFORE YOU BEGIN
READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY. TO AVOID PERSONAL INJURY AND /OR PRODUCT
DAMAGE. ALL OF THE INSTRUCTIONS BELOW MUST BE FOLLOWED.
1
I
N
S
T
A
L
L
A
T
I
O
N
G
U
I
D
E
LED HID REPLACEMENT LAMP INSTALLATION GUIDE
Caution-IF THE LAMP OR LUMINAIRE EXHIBITS UNDESIRABLE OPERATION (BUZZING, FLICKERING, ETC), IMMEDIATELY TURN OFF
POWER , REMOVE LAMP FROM LUMINAIRE AND CONTACT THE MANUFACTURER OR DISTRIBUTOR.
WARNING - Follow the installation instructions to install correctly.
• Disconnect power at the source before installation, inspection or removal. Do not simply switch off fixture.
• This item is rated at 120-277VAC/100-240VAC. Installer must determine whether line voltage 120-277VAC/100-240VAC is available at
the luminaire before installation.
• Not intended for use with emergency exit fixtures or emergency exit lights.
• Not for use with luminaire ballast.
• Do not use if product is damaged.
• This lamp is non-dimmable. Not for use with dimmer.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• Risk of fire or electric shock. Do not open or modify. No user serviceable parts inside.
• Installers should not disconnect existing wires from lamp holder terminals to make new connections at lamp holder terminals. Instead
installers should cut existing lamp holder leads away fr
om the lamp holder and make new electrical connections to lamp holder lead wires
by employing applicable connections.
• Suitable for damp locations. Suitable for use in wet locations when used in an outdoor -rated fixture. Not for use where directly exposed to
the weather or water
• Complies with part 15 of FCC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference , and
(2) This device must accept any interference received including interference that may cause undesired operation.
• No external weight or mechanical force should be applied to lamp or components.
• THE RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION
SHALL BE DETERMINED BY UL OR AUTHORITIES HAVING JURISDICTION.
BEFORE YOU BEGIN
READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY. TO AVOID PERSONAL INJURY AND /OR PRODUCT
DAMAGE. ALL OF THE INSTRUCTIONS BELOW MUST BE FOLLOWED.
1
ProLED
®
HID Retrot
Installation Instructions