Installation Guide

© 2018 Halco Lighting Technologies, LLC. All rights reserved. Halco and ProLED are registered trademarks of Halco Lighting Technologies. All sizes and specications are subject to change. Print Edition 12-18-18.
Halco Lighting Technologies | 2940 Pacic Drive | Norcross, GA 30071 | Toll Free 800.677.3334 | Phone [phone] | Fax [phone] | halcolighting.com | Atlanta | Carlstadt | Cleveland | Houston | Los Angeles | Phoenix
Push Gear Tray towards Strip Brackets so that
the Gear Tray sits aush with the brackets and
strip housing. Make sure the slots of the gear
tray and bracekts are aligned. Fasten Gear Tray
by inserting and turning 1/4-turn fasteners (F)
90°.
Remove protective packaging from LED modules and lens.
Place Lens Diffuser onto retrot kit by squeezing sides of
Lens Diffuser and inserting edges into grooves of Gear Tray.
Lens may need to be adjusted by squeezing sides or pressing
the face of the lens.
OPTION A:
Securely fasten ground screw lead from Gear
Tray (B) to host strip xture if host strip is
grounded.
Follow instructions and wiring diagram on Page 2 to connect AC
mains to Gear Tray input leads. Retrot kit comes equipped with
quick disconnect. Hide wires behind Gear Tray. Ensure leads do
not hang out of Gear Tray to avoid electrical wiring being clamped
between metal parts.
For 8ft. kit, the kit will come with (2) LED Gear Trays (A and B). Gear tray A will have a driver. Connect output leads
from Driver located on Gear Tray A to the leads on Gear Tray B by plugging in connector. Ensure leads are connected
correctly: Red (+) and Blue (-) from Driver to LED modules.
OPTION B:
Connect ground from Gear Tray (B) to supply
ground lead from conduit.
Phone: [phone]
Fax: [phone]
SHANGHAI HONGBAO LIGHTING CO., LTD.
NO.888 EAST HUIWANG ROAD, JIADING DISTRICT, SHANGHAI, CHINA 201815
LED STRIP RETROFIT KIT
Push Gear Tray towards Strip Brackets so that
the Gear Tray sits aush with the brackets and
strip housing. Make sure the slots of the gear
tray and bracekts are aligned. Fasten Gear Tray
by inserting and turning 1/4-turn fasteners (F)
90°.
Remove protective packaging from LED modules and lens.
Place Lens Diffuser onto retrot kit by squeezing sides of
Lens Diffuser and inserting edges into grooves of Gear Tray.
Lens may need to be adjusted by squeezing sides or pressing
the face of the lens.
OPTION A:
Securely fasten ground screw lead from Gear
Tray (B) to host strip xture if host strip is
grounded.
Follow instructions and wiring diagram on Page 2 to connect AC
mains to Gear Tray input leads. Retrot kit comes equipped with
quick disconnect. Hide wires behind Gear Tray. Ensure leads do
not hang out of Gear Tray to avoid electrical wiring being clamped
between metal parts.
For 8ft. kit, the kit will come with (2) LED Gear Trays (A and B). Gear tray A will have a driver. Connect output leads
from Driver located on Gear Tray A to the leads on Gear Tray B by plugging in connector. Ensure leads are connected
correctly: Red (+) and Blue (-) from Driver to LED modules.
OPTION B:
Connect ground from Gear Tray (B) to supply
ground lead from conduit.
Phone: [phone]
Fax: [phone]
SHANGHAI HONGBAO LIGHTING CO., LTD.
NO.888 EAST HUIWANG ROAD, JIADING DISTRICT, SHANGHAI, CHINA 201815
LED STRIP RETROFIT KIT