Installation Guide

ManualsBrandsHALCO LIGHTING TECHNOLOGIES ManualsLED Tube Lights17-Watt Equivalent 2 ft. Linear T8 LED Tube Light Bulb Non-Dimmable Bypass Type B Bright White 3500K (25-Pack)

Table Of Contents

ProLED Single or Double Ended Bypass T8

Single or Double-Ended Bypass T8

DANGER - RISK OF SHOCK-DISCONNECT POWER BEFORE INSTALLATION.

WARNING - RISK OF FIRE OR ELECTRIC SHOCK. LED RETROFIT KIT INSTALLATION REQUIRES KNOWLEDGE

OF LUMINAIRES ELECTRICAL SYSTEMS. IF NOT QUALIFIED, DO NOT ATTEMPT INSTALLATION AND

CONTACT A QUALIFIED ELECTRICIAN.

WARNING - RISK OF FIRE OR ELECTRIC SHOCK. PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH

THE NATIONAL ELECTRICAL CODE OR YOUR LOCAL ELECTRICAL CODE. IF YOU ARE NOT FAMILIAR WITH

THESE CODES

AND REQUIREMENTS, CONTACT A QUALIFIED ELECTRICIAN.

WARNING - RISK OF FIRE OR ELECTRIC SHOCK. INSTALL THIS KIT ONLY IN LUMINAIRES THAT HAVE THE

CONSTRUCTION FEATURES AND DIMENSIONS SHOWN IN THE PHOTOGRAPHS AND/OR DRAWINGS AND

WHERE THE INPUT RATING OF THE RETROFIT KIT DOES NOT EXCEED THE INPUT RATING OF THE

LUMINAIRE.

WARNING - TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET

MET

AL OR OTHER SHARP OBJECTS. DO NOT MAKE OR ALTER ANY OPEN HOLES IN AN ENCLOSURE OF

WIRING OR ELECTRICAL COMPONENTS DURING KIT INSTALLATION.

INSTALLERS SHOULD NOT DISCONNECT EXISTING WIRES FROM LAMPHOLDER TERMINALS TO MAKE NEW

CONNECTIONS AT LAMPHOLDER TERMINALS. INSTEAD INSTALLERS SHOULD CUT EXISTING LAMPHOLDER

LEADS AWAY FROM THE LAMPHOLDER AND MAKE NEW ELECTRICAL CONNECTIONS

TO LAMPHOLDER

LEAD WIRES BY EMPLOYING APPLICABLE CONNECTORS.

WARNING - RISK OF FIRE OR ELECTRIC SHOCK. LUMINAIRE WIRING AND ELECTRICAL PARTS MAY BE

DAMAGED WHEN INSTALLING OF RETROFIT KIT HARDWARE. CHECK FOR ENCLOSED WIRING AND

COMPONENTS.

WARNING - RISK OF FIRE OR ELECTRIC SHOCK. CHECK THE EXISTING WIRING FOR DAMAGE BEFORE

INSTALLING UPGRADE KIT. DO NOT INSTALL IF EXISTING WIRES ARE DAMAGED.

THE RETROFIT KIT IS

ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE

COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION. PRODUCT MUST BE

INSTALLED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH THE APPLICABLE AND APPROPRIATE

ELECTRICAL CODES. THE INSTALLATION GUIDE DOES NOT SUPERSEDE LOCAL OR NATIONAL

REGULATIONS FOR ELECTRICAL INSTALLATIONS.

"THIS LUMINAIRE HAS BEEN MODIFIED TO OPERA

TE LED LAMPS. DO NOT ATTEMPT TO INSTALL OR

OPERATE FLUORESCENT LAMPS IN THIS LUMINAIRE,“ SHALL BE MARKED ON THE RETROFIT LUMINAIRE

WHERE READILY VISIBLE BY THE USER DURING NORMAL MAINTENANCE INCLUDING LAMPS.

DO NOT USE WITH DIMMERS.

SUITABLE FOR DAMP LOCATIONS. SUITABLE FOR USE IN ENCLOSED LUMINAIRES.

THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY EXITS.

HIS DEVICE COMPLIAS WITH PAR

T 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING

TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE

MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE

UNDESIRED OPERATION.

Page: 1

General Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Summary of content (6 pages)

PAGE 1
ProLED Single or Double Ended Bypass T8 ® Single or Double-Ended Bypass T8 General Safety Information READ AND FOLLOW ALL SAFETY INSTRUCTIONS DANGER - RISK OF SHOCK-DISCONNECT POWER BEFORE INSTALLATION. WARNING - RISK OF FIRE OR ELECTRIC SHOCK. LED RETROFIT KIT INSTALLATION REQUIRES KNOWLEDGE OF LUMINAIRES ELECTRICAL SYSTEMS. IF NOT QUALIFIED, DO NOT ATTEMPT INSTALLATION AND CONTACT A QUALIFIED ELECTRICIAN. WARNING - RISK OF FIRE OR ELECTRIC SHOCK.
PAGE 2
ProLED Single or Double Ended Bypass T8 ® Single or Double-Ended Bypass T8 Installation Instructions (Double-Ended) 1. Make sure the circuit breaker that supplies the power to the fixture is turned off. 2. Remove lens or diffuser cover (if applicable) and existing fluorescent lamps. 3. Open/Remove ballast wiring compartment cover. 4. Identify the line and neutral wires running from the breaker box to the ballast and confirm the power is off using a voltmeter. 5.
PAGE 3
ProLED Single or Double Ended Bypass T8 ® Single or Double-Ended Bypass T8 Installation Instructions (Single-Ended) 1. Make sure the circuit breaker that supplies the power to the fixture is turned off. 2. Remove lens or diffuser cover (if applicable) and existing fluorescent lamps. 3. Open/Remove ballast wiring compartment cover. 4. Identify the line and neutral wires running from the breaker box to the ballast and confirm the power is off using a voltmeter. 5.
PAGE 4
ProLED Single or Double Ended Bypass T8 ® T8 à dérivation et à une ou deux extrémités Informations générales sur la sécurité LIRE ET SUIVRE TOUTES LES INSTRUCTIONS DE SÉCURITÉ DANGER - RISQUE DE CHOCS - DÉCONNECTEZ L’ALIMENTATION ÉLECTRIQUE AVANT L’INSTALLATION. AVERTISSEMENT - RISQUE D’INCENDIE OU D’ÉLECTROCUTION. L’INSTALLATION D’UN KIT D’INSTALLATION RETROFIT A LED NÉCESSITE UNE BONNE CONNAISSANCE DES SYSTÈMES ÉLECTRIQUES DES LUMINAIRES.
PAGE 5
ProLED Single or Double Ended Bypass T8 ® T8 à dérivation et à une ou deux extrémités Instructions d’installation (deux extrémités) 1. Assurez-vous que le disjoncteur qui alimente le projecteur soit désarmé (éteint). 2. Retirez la lentille ou le couvercle du diffuseur (le cas échéant) et les lampes fluorescentes existantes. 3. Ouvrir/retirer le couvercle du compartiment de câblage du ballast. 4.
PAGE 6
ProLED Single or Double Ended Bypass T8 ® T8 à dérivation et à une ou deux extrémités Instructions d’installation (une extrémité) 1. Assurez-vous que le disjoncteur qui alimente le projecteur soit désarmé (éteint). 2. Retirez la lentille ou le couvercle du diffuseur (le cas échéant) et les lampes fluorescentes existantes. 3. Ouvrir/retirer le couvercle du compartiment de câblage du ballast. 4.