User Manual

ManualsBrandsHale ManualsEquipmentFoamLogix 2.1A-LF Low Foam Flow Calibration

Quick Start Guide

(FoamLogix 2.1A-LF Low Foam Flow Calibration)

1. If not already attached, connect a hose

to the barbed tting located on the 3-way

bypass valve on the foam pump/motor

assembly.

2. Place the hose into a clean calibrated

measuring container to conne the

discharged foam. The original 5 gallon

foam container works well.

3. Turn the bypass valve handle so that the

ARROW points in the direction of the

barbed tting (foam ows out the bypass).

4. Make certain the FoamLogix display

is showing the water ow rate screen

(“FLOW” LED is ON). If not, press the “i”

button until the water ow rate screen is

shown.

5. Put the FoamLogix display into

simulated water ow by pressing the UP

ARROW and DOWN ARROW buttons

simultaneously.

English Units

The FoamLogix display should show “S

150” or less (Simulated ow, 150 gpm).

Metric Units

The FoamLogix display should show

“S 567” or less (Simulated ow, 567 lpm).

If not, use the UP/DOWN arrow buttons

to adjust the value.

6. Press the “i” button once on the Foam

Logix display to show the foam rate

percentage screen (“%” LED is ON). Use

the UP/DOWN ARROW buttons to set the

foam ow percentage to 0.1%

7. Press the ON/OFF button on the Foam

Logix display. The system will begin

owing foam. Press the ON/OFF button

after 10 seconds to stop the foam ow.

8. Press and hold the DISPLAY button (

on the FoamLogix display until PASS is

shown – approximately 2 seconds. (See

Figure 1.)

9. With the DISPLAY button (

i) pressed,

press the INCREASE button 4 times

( ). (See Figure 2)

A u is shown with each INCREASE

button press.

10. Release the DISPLAY button (

i). The

display shows CAL for about 2 seconds

indicating the calibration mode is

entered.

11. Press the DISPLAY button (

i) 4 times

until A 0.00 is shown. (See Figure 3 on

the next page.)

12. Press the red ON/OFF button ( ). The

bar graph illuminates 7 bars, the foam

motor begins running, and the display

value starts increasing. (See Figure 4 on

next page.)

Calibration

FoamLogix

Figure

THIS QUICK START GUIDE IS ONLY INTENDED AS A BRIEF OVERVIEW TO THE

OPERATION OF THE FOAMLOGIX 2.1A-LF SYSTEM AND IS NOT INTENDED TO

BE A REPLACEMENT FOR THE CURRENT INSTALLATION/OPERATION MANUAL

(029-0021-74-0) PROVIDED WITH EACH SYSTEM.

ALSO AVAILABLE ON-LINE – WWW.CLASS1.COM.



Figure

Summary of content (2 pages)

PAGE 1
Quick Start Guide (FoamLogix 2.1A-LF Low Foam Flow Calibration) THIS QUICK START GUIDE IS ONLY INTENDED AS A BRIEF OVERVIEW TO THE OPERATION OF THE FOAMLOGIX 2.1A-LF SYSTEM AND IS NOT INTENDED TO BE A REPLACEMENT FOR THE CURRENT INSTALLATION/OPERATION MANUAL (029-0021-74-0) PROVIDED WITH EACH SYSTEM. ALSO AVAILABLE ON-LINE – WWW.CLASS1.COM. Calibration If not already attached, connect a hose to the barbed fitting located on the 3-way bypass valve on the foam pump/motor assembly. 2.
PAGE 2
Figure 3 16. Repeat preceding Steps 12 through 14. 17. Press the DISPLAY button ( i ) to view the foam flow calibration factor. Write this number down for future reference. (See Figure 6). Verify that the foam calibration factor is between 270 and 310. FoamLogix Contact customer service at 1-800-533-3569 if the calibration factor does not fall within the required calibration range. Figure 4 Figure 6 FoamLogix FoamLogix Figure 5 18.