Video to PC/HDTV Switching Scaler Composite, S-Video, Component, PC and HDMI AV Inputs HDMI AV Output with Separate Digital Audio Output Front Panel, IR Remote, & RS-232 Serial Control MODEL SC1080-H UMA1165 Rev A SUPPORT & ORDERING INFORMATION For technical support, Call 714-641-6607 or fax 714-641-6698 Order by phone: toll-free in the U.S. 800-959-6439 Web site: www.hallresearch.com Hall Research 1163 Warner Ave.
Multi Input Digital Scaler with Audio TRADEMARKS USED IN THIS MANUAL Hall Research, HR, and the logo are trademarks of Hall Research Inc. Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners.
Model SC1080-H Contents 1. INTRODUCTION ........................................................................................................... 3 1.1 GENERAL ........................................................................................................... 3 1.2 FEATURES......................................................................................................... 4 2. INSTALLATION ......................................................................................................
Multi Input Digital Scaler with Audio 1. Introduction 1.1 General The SC1080-H is a multiple format switching video scaler. It has 5 different types of video inputs and a scaled digital output that can be switched to any of the inputs. The SC1080-H accepts various input formats and resolutions and scales to a specific output format and resolution.
Model SC1080-H 1.2 Features • • • • • • • • • • • • • • HDMI 1.2, HDCP 1.1 and DVI 1.0 Compliant. 5 different inputs: HDMI, PC, YPbPr, S-video and Composite. Provides YPbPr HDTV outputs of 480i/p, 576i/p, 720p, 1080i, 1080p and up to WUXGA (1920x1200) PC resolutions Converts Digital and Analog audio signals into Digital Format for output on HDMI combined with the video or separate Coaxial S/PDIF. RS-232 interface allows control from an external device. OSD (On-Screen Display).
Multi Input Digital Scaler with Audio 2. Installation 2.1 Connecting the Video inputs The video scaler accepts both TV and PC inputs and scales them to your desired high resolution format output. The TV inputs are composite video (CV), S-Video (Mini-Din connector), YPbPr input (3 RCA connectors), PC (HD15) and HDMI™. Figure 2 - Rear Panel S-Video: Use an S-Video cable to connect the S-Video output of the source equipment to the connector labeled “S-Video” on the back of the Video Scaler.
Model SC1080-H 2.2 Connecting the Scaled Output The output of the SC1080-H can be connected to any HDMI™ compatible LCD, Projector, or Plasma display by using the appropriate cable. Figure 3 - Block Diagram 2.3 Other Connections RS-232: Connect a serial control device to the 9-pin D-sub connector labeled “RS-232” Power: Use only the 5V 2.6A DC power input (center positive 2.1 mm jack) supplied with the unit.
Multi Input Digital Scaler with Audio 3. Configuration & Operation 3.1 Front Panel 5 6 1 2 4 3 Figure 4 - Front Panel 1. Source Selection: Press the appropriate button to output that connected audio and video selection. 2. Menu: Press the menu button to bring up the OSD operation menu. 3. Enter: Press the button to confirm selections made in the OSD. 4. ▲or▼: Press to toggle through various adjustment controls to alter the settings. 5. IR Sensor: Infrared remote control sensor. 6.
Model SC1080-H 3.
Multi Input Digital Scaler with Audio 3.
Model SC1080-H 3.4 Infra-Red Remote control (IR Remote) 1. Power: Power unit ON/OFF. 2. Input: Toggle through input sources. 3. HD: Select Component Input. 4. PC: Select PC input. 5. HDMI/DVI: Select HDMI Input. 6. Output Resolution: Select various output resolutions directly. Others are available via the OSD. 7. EXIT: Select to exit OSD menu 8. MENU: Select to show OSD 9. OK: Select to confirm a selection. 10. UP/DOWN/LEFT/RIGHT: Select to move in OSD menu or to change a selection. 11.
Multi Input Digital Scaler with Audio 3.5 Front Panel Lockout Under certain circumstances it may be desirable to disable the front panel controls (e.g. to prevent unauthorized or accidental changes to the settings while the unit is in use). To disable the front panel controls you must use the RS-232 port (see Serial Control section for details).
Model SC1080-H 4. Serial Control The video input selection and signal parameter settings for the SC1080H can be controlled via an external control system by using the RS-232 port on the unit. Use a straight thru M/F DB9 serial cable to connect the unit to the PC. Only the TX, RX and GND pins are implemented in the connector. The RS232 port operates at 19200 baud, no parity and 1 stop bit. In response to a valid command, the SC1080-H will respond with CR, LF, >, SPACE and then the listed response.
Multi Input Digital Scaler with Audio 4.
Model SC1080-H 4.2 Key Commands Command K POWER K MENU K UP K DOWN Response > POWER > MENU > UP > DOWN Description PRESS POWER BUTTON PRESS MENU BUTTON PRESS UP BUTTON PRESS DOWN BUTTON An invalid command will respond with “K-[??]” 4.
Multi Input Digital Scaler with Audio S OUTPUT 17 > OUTPUT WSXGA S OUTPUT 18 > OUTPUT WUXGA S OUTPUT 19 > OUTPUT WXGA+ S OUTPUT 20 > OUTPUT SXGA+ S SIZE 0 S SIZE 1 > SIZE FULL > SIZE OVERSCAN S SIZE 2 > SIZE UNDERSCAN S SIZE 3 > SIZE LETTERBOX S SIZE 4 > SIZE PANSCAN S PICTUREMODE 0~3 > PICTUREMODE STANDARD~USER S CONTRAST 0~100 > CONTRAST 0~100 S BRIGHTNESS 0~100 > BRIGHTNESS 0~100 S HUE 0~100 > HUE 0~100 S SATURATION 0~100 > SATURATION 0~100 S SHARPNESS 0~100 > SHARPNESS 0~100
Model SC1080-H S OSDHPOSITION 0~100 > OSDHPOSITION 0~100 S OSDVPOSITION 0~100 > OSDVPOSITION 0~100 S OSDTIMEOUT 0~100 > OSDTIMEOUT 0~100 S OSDBACKGROUND 0~8 > OSDBACKGROUND 0~8 S AUDIOMUTE 0~1 > AUDIOMUTE OFF~ON S AUDIODELAY 0~1 > AUDIODELAY OFF~ON S MIRROR 0~1 > MIRROR OFF~ON S KEYLOCK 0~1 > KEYLOCK OFF~ON S RESET 0~1 > RESET ON OSD H POSITION 0~100 ADJUST [Default:50] OSD V POSITION 0~100 ADJUST [Default:50] OSD TIMEOUT 0~100 SETTING [Default:10] SECONDS OSD OSDBACKGROUND 0~8 ADJUST [Def
Multi Input Digital Scaler with Audio 5. Troubleshooting Hall Research highly recommends that all products be assembled, configured and tested prior to the final installation to eliminate the possibility of problems on site. There are no field serviceable parts or circuits in the device. If you think that the device is malfunctioning, please first try to reset to factory default settings: 5.1 Resetting the SC1080-H to Factory Defaults There are no field serviceable parts or circuits in the device.
Model SC1080-H 6. Specifications 6.1 Supported Input Formats Resolution 480i/576i 480p/576p 720p@(60/50) 1080i@(60/50) 1080p@(60/50) VGA@(60/72/75/85) SVGA@(56/60/72/75/85) XGA@(60/70/75/85) SXGA@(60/75/85) UXGA@60 WXGA@60(1280X800) WXGA+(1440x900) SXGA+(1400x1050) WSXGA@60(1680X1050) WUXGA@60(1920X1200) 6.
Multi Input Digital Scaler with Audio 19
Model SC1080-H 20
© Copyright 2009. Hall Research Inc. All rights reserved. 1163 Warner Ave.