Installation Guide

ManualsBrandsHallman ManualsHousehold Appliance30 in. Smooth Top Electric Cooktop in Stainless Steel with 5 Elements including Flex-Power Element

INSTALLATION REQUIREMENTS

Tools and Parts

Location Requirements

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

Tape measure Marker or pencil

1/4"(6.35mm) nut driver Pliers

Flat-blade screwdriver

Parts supplied

Foam strip roll 2 "(6.4cm)clamping

Clamping brackets(2)

Parts needed

AUL listed or CSA approved connector for "(1.3cm)

diameter conduit

UL listed wire connectors

Check local codes. Check existing electrical supply. See the

“Electrical Requirements” section.

It ie recommended that all electrical connections be made by a

licensed, qualified electrical installer.

screws(2)

IMPORTANT: Observe all governing codes and ordinances.

When installing cooktop, use minimum dimensions given.

To eliminate the risk of burns or fire by reaching over the

heated surface units, cabinet storage space locates above

the surface units should be avoided. If cabinet storage is to

be provided. The risk can be reduced by installing a range

hood that projects horizontally a minimum of 5"(12.7cm)

beyond the bottom of the cabinets.

The cooktop must be a specified cooktop that is approved to

be installed either alone or over an undercounter built-in

oven.Check the cooktop base for an approved installation

label.If you do not find this label, contact your dealer to

confirm that your cooktop is approved.

The cooktop must be installed in a level countertop.

Ovens approved for this type of installation will have an

approval label located on the top of the oven. If you do not

find this label, contact your dealer to confirm that your oven is

Instructions for approval for built-in undercounter use and

proper cutout dimensind.

The cooktop should be installed away from strong draft

areas ,such as windows, doors, fans or strong heating vents.

The cooktop should be located for convenient use in the

kitchen.

Use the countertop opening dimensions that are given with

these Installation Instructions. Given dimensions are

minimum clearances and provide 0" (0 cm) clearance.

approved. Refer to oven manufacturer's Installation

Grounded electrical supply is required. See “Electrical

Requirements” section.

IMPORTANT: To avoid damage, check with your builder or

cabinet supplier to make sure that the materials used will not

discolor, delaminate or sustain other damage.

Product Dimensions

A.21 "(55,2 cm)

B.30"(76.2cm)models - 30 "(78.4cm)

36"(91.4cm)models - 36 "(92.3cm)

C.3 "(9.5cm)

／

Summary of content (7 pages)

PAGE 1
INSTALLATION REQUIREMENTS Location Requirements Tools and Parts IMPORTANT: Observe all governing codes and ordinances. When installing cooktop, use minimum dimensions given. To eliminate the risk of burns or fire by reaching over the heated surface units, cabinet storage space locates above the surface units should be avoided. If cabinet storage is to be provided. The risk can be reduced by installing a range hood that projects horizontally a minimum of 5"(12.7cm) beyond the bottom of the cabinets.
PAGE 2
Cabinet Dimensions Electrical Requirements IMPORTANT: If installing a range hood or microwave hood combination baove the cooktop, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface. Electrical Shock Hazard Disconnect power before servicing. Use 8 gauge copper wire. Electrically ground cooktop. Failure to follow these instructions can result in death, fire,or electrical shock.
PAGE 3
A UL listed or CSA approved conduit connector must be provided at each of the power supply cable (at the cooktop and at the junction box). A listed conduit connector is already provided at the cooktop. The cooktop should be connected directly to the junction box through flexible, armored or nonmetallic sheathed, copper cable. The flexible, armored cable extending from the fuse box or circuit breaker box should be connected directly to the junction box.
PAGE 4
Installing Brackets Before Placing Cooktop in Cutout 1. Using 2 or more people,place the cooktop upside down on a covered surface using the foam end posts form the packaging. 2. Remove the attachment screws for the bracket locations from the bottom of the cooktop base. 3. Select bracket mounting holes that will allow the bracket to extend far enough out from the cooktop for the installation of 21／2 "(6.4cm) clamping screws.
PAGE 5
Make Electrical Connection 4-Wier Cable from Power Supply to 4-Wire Cable from Cooktop IMPORTANT: Use the 4-wire cable from power supply where local codes do not permit connecting the frame-ground conductor to the neutral (white) junction box wire. Electrical Shock Hazard Disconnect power before servicing. Use 8 gauge copper wire. Electrically ground cooktop. Failure to follow these instructions can result in death, fire,or electrical shock.
PAGE 6
3-Wier Cable from Power Supply to 4-Wire Cable from Cooktop IMPORTANT: Use the 3-wire cable from power supply where local codes permit connecting the frame-ground conductor to the neutral (white) junction box wire: A.3-Wire cable from power supply B. Red wires C. White and green or bare ground wires (from cooktop) D. 4-wire cable from cooktop E. Junction box F. White wire (from power supply) G. UL listed wire connector H. Black wires I. UL listed or CSA approved conduit connector 1. Disconnect power. 2.
PAGE 7
3-Wier Cable from Power Supply to 3-Wire Cable from Cooktop Attach Cooktop to Countertop NOTE: This section applies only if you are using clamping brackets. IMPORTANT:Use the 3-wire cable from power supply where local codes permit connecting the frame-ground conductor to the neutral (white) junction box wire: A.3-wire cable from power supply B.Red wires C.Green or bare ground wrie (from cooktop) D.3-wire cable from cooktop A. Glass cooktop B. Cooktop base C. Attachment screw D.