Specification

HALO LED H4 Series - 2nd Generation
The Halo H4 LED is a family of 4” aperture recessed downlight
H457 series of housings designed for exclusive use with Halo
EL406, ELG406, ELSG406 Series LED Light Engines and compatible
TL4 and TLS4 LED trims. Halo H4 LED housings have integral LED
drivers that offer dimming as a standard feature.
This is an insulated ceiling*, AIR-TITE™, remodel housing offering
120 volt dimming capability. The H4 LED series offers high quality
downlighting along with high efficacy – the result being great light-
ing and significant energy savings.
MECHANICAL
Housings
Single wall formed aluminum
construction. Openings are
gasketed for AIR-TITE installation.
5 1/2” height allows use in 2”x 6
joist construction. AIR-TITE
aperture gasket is pre-installed.
Remodel Arm
• Spring steel construction
designed for ease of installation
and ceiling support of LED driver.
MOUNTING
Remodel Springs
• Four remodel clips secure
housing and accommodate
1/2” and 5/8” ceiling material.
ELECTRICAL
Junction Box
• Seven 1/2” trade size conduit
knockouts with true pry-out slots
• Slide-N-Side™ connectors allow
non metallic sheathed cable to
be installed without tools and
without removing knockouts.
• Accepts a wide range of
non-metallic sheathed cables
- The standard cable types used
in lighting in both U.S. and
Canada.
- Allows wiring connections to
be made outside the junction
box.
- Simply insert the cable directly
into the trap after connections
are made.
- Accommodates the following
standard nonmetallic sheathed
cable types:
US: #14/2, #14/3, #12/2, #12/3
Canada: #14/2, #14/3, #12/2
LED LIght Engine Connection
• LED connector is a non-screw base
connector offering easy installation
with the H4 LED 2nd Generation
EL406, ELG406, ELSG406 Series
LED Light Engines.
• LED connector meets high-
efficacy luminaire requirement
for a non-screw base socket, and
where required to qualify as a
high-efficacy luminaire (California
Title-24).
LED Driver
• LED dimmable driver mounts to
the housing junction box.
• Driver is a 120 Volt, high
efficiency, electronic power
supply providing low voltage
power to EL Series LED Light
Engines.
• Driver meets FCC EMI/RFI
Consumer Level limits for use
in residential and commercial
installations.
• Driver features power factor
>.90, THD <20% and has integral
thermal protection in the event
of over temperature or internal
failure.
• Driver is specifically designed
for compatibility with EL406
LED Light Engines, and ELG406,
ELSG406 Adjustable Gimbal Light
Engine / Trims.
• If dimming is not required the
fixture can be operated from a
standard wall switch.
Dimming
• The HALO H4 LED luminaire is
designed for dimming
capability to 10% in normal
operation with most 120V
leading edge (LE) and trailing
edge (TE) phase control
dimmers. H4 LED may also
dim to 5% using dimmers
with low end trim adjustment.
(Consult dimmer manufacturer
for application/compatibility/
loading. Note, some dimmers
require a neutral in the wallbox).
Warranty
Eaton provides a five year limited
warranty on Halo LED Luminaires
which includes the LED Recessed
Housing, LED Light Engine, and LED
trims.
Labels
• UL/cUL Listed 1598 Luminaire
• UL/cUL Listed for Damp Location
• UL/cUL Listed for Wet Location,
covered ceiling - with select trims
• UL/cUL listed for Direct Contact
with insulation and combustible
material*
Qualifications
• ENERGY STAR
®
Certification.**
• Use with designated LED light
engines and trims for State of
California Title 24 high efficacy
luminaire compliance**
• Can be used for International
Energy Conservaction Code (IECC)
high efficacy luminaire
compliance
IC and AIR-TITE™
Certified under ASTM-E283 and
listed UL/cUL 1598. May be used to
meet insulated ceiling and restricted
air-flow requirements such as:
• International Energy
Conservation Code (IECC)
• State of California Title 24
“Recessed Downlight Luminaires
in Ceilings.”
DESIGN FEATURES
H457RICAT1E
4-Inch LED Recessed
Remodel Housing
Insulated Ceiling
High Efficacy LED Housing-
Dimmable
TD518274EN
August 10, 2017 4:25 PM
H4 Series LED Energy Data:
(Values at non-dimming line voltage.)
Minimum Starting Temp:
-30°C (-22°F)
EMI/RFI: FCC Title 47 CFR, Part 18,
(Consumer)
Sound Rating: Class A standards
Input Voltage: 120V
Power Factor: >0.90
Input Frequency: 50/60Hz
THD: <20%
Input Power: 13W
Input Current: 120mA
Driver Compliance: UL8750,
Class II rated
Maximum IC (Insulated Ceilng)
Ambient Continuous Operating Room
Temperature: 25°C (77°F)
Maximum Non-IC (Non-Insulated
Ceilng) Ambient Continuous Operating
Room Temperature: 40°C (104°F)
Catalog #
Project
Comments
Prepared by
Type
Date
HALO
®
*
Not for use with housings in direct contact with spray foam insulation.
**
Refer to ENERGY STAR
®
Certied Products List and CEC Appliance Database for listings.
FOR USE IN
INSULATED CEILINGS
FOR DIRECT CONTACT
WITH INSULATION*
ALSO SUITABLE FOR
NON-IC APPLICATIONS