Instruction Manual

ManualsBrandsHalo ManualsKitchen6 in. Recessed New Construction IC Air-Tite Housing

Table Of Contents

WARNING - RISK OF ELECTRIC SHOCK. DISCONNECT MAIN

POWER AT FUSE OR CIRCUIT BREAKER BEFORE

INSTALLING OR SERVICING THE FIXTURE.

LED 5” & 6” RETROFIT TRIM

INSTALLATION INSTRUCTIONS

Please read carefully and save these instructions as

you may need them at a later date.

GENERAL: All electrical connections must be in accordance with local

and National Electrical Code (N.E.C.) standards. If you are unfamiliar

with proper electrical wiring connections obtain the services of a

qualified electrician.

Remove the trim from the box and make sure that no parts are missing

by referencing the PARTS illustrations.

THIS RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF

A LED LUMINAIRE WHERE THE SUITABILITY OF THE

COMBINATION SHALL BE DETERMINED BY CSA OR CANADIAN

AUTHORITIES HAVING JURISDICTION.

_________________________________________________

WARNING- RISK OF FIRE OR ELECTRIC SHOCK

FOR USE WITH HOUSING MODELS: INCANDESCENT HOUSINGS

–

COMMERCIAL ELECTRIC HBR5ICAT, HBR5ICRAT, HBR5, HBR5R,

HALO H5T, H5RT, H5ICT, H5RICAT, C7IC, C7ICR, C7ICA, C7ICRA,

C7, C7R, C7S, HBR5000SIC; HALO H7ICT, H7RICT, H7ICAT,

H7RICAT, H7T, H7RT, H27ICT, H27T, H27RT, H750ICAT, H750RICAT;

CORDELIA X5LICAT, X5LICRAT, HBR7LICAT, HBR7LICRAT; CAPRI

CR1, CRR1; DMF DH6ICATQ, DH6ICRATQ; ELCO EL5ICA, EL5RICA;

LITHONIA L5, L5R, EL7ICA, EL7RICA; ELITE B5, B5R, B5IC, B5RIC,

B6IC, B6RIC; JUNO IC22, IC22R; LITHONIA L7X, L7XR; NORA NHIC-

17QAT, NHRIC-17QAT; PROGRESS P187-TG, P87-AT, P184-TG,

P84-AT; SEA GULL 11018, 11028; THOMAS PS1, PS1-RM. HALO

LED HOUSINGS – H550ICAT, H550RICAT H750ICAT, H750RICAT.

• Do not alter, relocate, or remove wiring, lampholders, power supply,

or any other electrical component. Installation of the retrofit

assembly requires a person familiar with the construction and

operation of the luminaire’s electrical system and the hazard

involved. If not qualified, do not attempt installation. Contact a

qualified electrician.

• Do not make or al

ter any open holes in an enclosure of wiring or

electrical components during kit installation.

• To prevent w

iring damage or abrasion, do not expose wiring to

edges of sheet metal or other sharp objects.

____________________________

ASSEMBLY AND INSTALLATION

1. If using a 5 inch housing, remove the screws on the TORSION

SPRINGS and screw the TORSION SPRINGS into the upper tab.

(FIG. 1)

INCANDESCENT HOUSINGS

1. Unscrew the WING NUT inside the CAN to detach the SOCKET

BRACKET from the CAN. Disengage the SOCKET from the

SOCKET BRACKET. (FIG. 2)

2. Thread the

SOCKET ADAPTER into the SOCKET. (FIG. 3)

3. Plug the MA

LE CONNECTOR of the SOCKET ADAPTER to the

FEMALE CONNECTOR of top of the RETROFIT TRIM. (FIG. 4)

4. Squeeze bot

h TORSION SPRING arms together and insert into the

TORSION SPRING SLOTS (or C-CLIPS) of the CAN. (FIG. 5)

PARTS

SOCKET ADAPTER ASSEMBLY

RETROFIT TRIM

COMPATIBLE HOUSING

DIMENSIONS

5 in. – 7 in.

5 in. – 6 in.

FIG. 1

FIG. 2

FIG. 4

FIG. 3

FIG. 5

Summary of content (4 pages)

PAGE 1
LED 5” & 6” RETROFIT TRIM INSTALLATION INSTRUCTIONS Please read carefully and save these instructions as you may need them at a later date. GENERAL: All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician. PARTS COMPATIBLE HOUSING DIMENSIONS SOCKET ADAPTER ASSEMBLY 5 in. – 7 in.
PAGE 2
5. Tuck all wires into the CAN and carefully push the RETROFIT TRIM into CAN. (NOTE: To provide enough room in shallow cans, carefully position SOCKET ADAPTER and SOCKET adjacent to the side of the LED DRIVER prior to inserting the RETROFIT TRIM into the CAN.) (FIG. 5) LED HOUSINGS 1. Plug the MALE CONNECTOR of the SOCKET ADAPTER to the FEMALE CONNECTOR of top of the RETROFIT TRIM. (FIG. 4) 2. Squeeze both TORSION SPRING arms together and insert into the TORSION SPRING SLOTS (or C-CLIPS) of the CAN. (FIG.
PAGE 3
INSTRUCCIONES PARA LA INSTALACIÓN DEL ADAPTADOR DECORATIVO LED DE 5” y 6” Lea cuidadosamente y guarde estas instrucciones ya que podría necesitarlas más adelante. GENERAL: Todas las conexiones eléctricas deben realizarse conforme a las normas locales y al Código Eléctrico Nacional (N.E.C. por sus siglas en inglés). Si no está familiarizado con las conexiones adecuadas de cableado eléctrico obtenga los servicios de un electricista calificado. DIMENSIONES DE LA CAJA PARTES ADAPTADOR DEL PORTALÁMPARAS 5 in.
PAGE 4
. Apriete las ABRAZADERAS e inserte en las RANURAS (o RECEPTOR DE ABRAZADERA) de el PORTALÁMPARAS. (FIG. 5) 5. Mete todos los cables en el PORTALÁMPARAS y empuje con cuidado la reconversión ADAPTADOR DECORATIVO en PORTALÁMPARAS. (NOTA: Para proporcionar suficiente espacio en los PORTALÁMPARAS de poca profundidad, con cuidado posicione el ADAPTADOR DEL ZÓCALO y el enchufe al lado de la CONTROLADOR antes de insertar el RECONVERSIÓNADO ADAPTADOR DECORATIVO en el PORTALÁMPARAS). (FIG. 5) CAJAS LED 1.