QUICK START GUIDE HS-1001-XNA TRILINGUAL ASSEMBLY STEPS AVAILABLE AT HALO-PG.
WARNING "Please read this entire manual before installation and use of this pellet-burning appliance. Failure to follow these instructions could result in property damage, bodily injury, or even death." WARNING The manufacturer has made every effort to eliminate any sharp edges. However, you should handle all components with care to avoid accidental injury. WARNING • “READ ALL INSTRUCTIONS BEFORE INSTALLING AND USING THE APPLIANCE.” • “SAVE THESE INSTRUCTIONS.
IMPORTANT: Please read all instructions thoroughly before proceeding. Find a large, clean area in which to assemble your HALO Prime550 Pellet Grill. Please refer to the assembly diagram, as necessary. Install Left-Inner Leg using (3)-M6 x 14mm Screws and install leg cap. 1 NOTICE: Make sure all the plastic protection is removed before assembling. Tool required for assembly: #2 Phillips Screwdriver 63 ITEM 65 PART DESCRIPTION QTY.
Install Left-Outer Leg using (3)-M6 x 14mm 2 Screws and install leg cap. ITEM PART DESCRIPTION QTY.
Install Left Outer Leg Assembly, Left Inner Leg 3 assembly using pivot bracket 68 & 69A, (2)-M6 x 2.5H x 9.5D shoulder screw, (1)-M6 x 63mm Knob w/ Threaded Shaft and Nylon-Spacer. Tighten screws firmly. Set assembly aside. ITEM PART DESCRIPTION QTY. 68 Pivot Bracket-B 1 69A Pivot Bracket-C 1 78 M6 x 63mm-Knob w/ Threaded Shaft 1 79 Nylon Spacer 1 81 M6 x 2.5H x 9.
4 ITEM 63 Install Right-Inner Leg using (3)-M6 x 14 Screws and install leg cap. PART DESCRIPTION QTY.
Install Right-Outer Leg using (3)-M6 x 14 Screws 5 and install leg cap. 63 ITEM PART DESCRIPTION QTY.
Install Right Outer Leg Assembly, Right Inner Leg 6 assembly using pivot bracket 69 & 69A, (2)-M6 x 2.5H x 9.5D shoulder screw, (1) x 63mm -Knob w/ Threaded Shaft and Nylon- Spacer. Tighten screws firmly. Set assembly aside. ITEM PART DESCRIPTION 69 Pivot Bracket-B 69A Pivot Bracket-C 1 1 78 M6 x 63 mm Knob w/ Threaded Shaft 79 Nylon Spacer 81 M6 x 2.5H x 9.5D-Shoulder Screw 79 78 81 69A 8 69 81 QTY.
7 Install Front Panel and Rear Brace assembly using (8)-M6 x 14mm screws. IMPORTANT: Do not tighten screws completely until all screws for that step have been installed. ITEM PART DESCRIPTION QTY.
Attach the Casters using M12 caster wrench. 8 Mount Casters with Lock to front legs and Mount Swivel casters to rear legs. NOTE: You can lock the casters that have locks, allowing you to assemble the caster without using a caster wrench. ITEM PART DESCRIPTION QTY.
Attach Brackets-Leg Support-Left and right 9 using 6-M6 x 12 Truss head screws. ITEM 61 62 80 PART DESCRIPTION QTY.
Turn the cart right up with front casters still in 10 locked position. Attach fire chamber assembly to the “X“ frame using (4) ¼”-20-Knob with Threaded Shaft to secure the cooking chamber in place. NOTE: We recommend the help of a friend to attach the fire chamber assembly onto the “X” cart frame due to the size and weight. ITEM 77 PART DESCRIPTION QTY.
11 Install cooking grid and warming rack. ITEM PART DESCRIPTION QTY.
11 Warming rack continued. Warming rack is in usual position. Step1. Slide warming forward until center support wire is pushed against front section of the bracket. Step2. Left up warming then hook on to the “J” brackets.
side table brackets left and right using 12 Install (12)-M6 x 14mm screws. Install side table left and right using (4)-M6 x 2.5H x 9.5D-Shoulder Screw. ITEM PART DESCRIPTION QTY. 19 Bracket-Side Table-A 2 Bracket-Side Table-B 2 Release Spring Pin-Side Table/Cleanout Tray 2 Side Table-Right 1 20 22 23 24 25 81 82 Side Table-Left 1 "JJ" Tool Hook 2 M6 x 2.5H x 9.
ash tray by pulling the release spring 13 1. Install pin, then insert the tray into the tray tracks and slide the tray all the way back. Release the spring pin to lock in place. 2. Insert the leveler into the housing.
14 Install grease cup with cover. ITEM 26 PART DESCRIPTION Grease Bucket w/ Cover QTY.
