Installation Manual

Instruction Manual/Instrucciones
Questions?/¿Preguntas?
1-800-334-6871 [e-mail]
1
HALO
®
1
HALO
®
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by the manufacturer
could void the user’s authorization to operate this equipment.
SAVE THESE INSTRUCTIONS.
MOUNTING YOUR FIXTURE
WARNING: Risk of electric shock. Disconnect
power at fuse or circuit breaker before installing
or servicing.
WARNING: Personal injury and damage to the
fixture and/or mounting surface may result if the
fixture is pulled from the surface. To reduce the
likelihood of injury or damage, mount only on a
surface that is structurally sound.
1. Remove fixture (A) from carton. Locate the parts
bag containing the (2) mounting screws (B) and set
aside until ready to mount the fixture.
2. Hold the fixture up to the undercabinet surface
where it will be mounted. Mark the position of the
mounting holes with a pencil. Set the fixture aside.
3. Drill a small pilot hole in the undercabinet surface
at each pencil mark.
4. Place the fixture (A) flush against the undercabinet
surface, lining up the mounting holes in the fixture
with the pre-drilled pilot holes.
5. Insert (2) mounting screws into the two mounting
holes (Fig. 1). Tighten both screws to secure fixture.
WIRING
NOTE: If using a splice box, follow instructions included
with the splice box.
CAUTION: Check electrical power wires for
damage or scrapes.
NOTE: This unit will not operate properly unless
connected to a “grounded” electrical circuit.
Electrical shock, over heating, low or no light
output, and shortened lamp life can result if not
properly grounded.
1. Connect power cord to the fixture.
2. Plug power cord into outlet.
NOTE: Additional fixtures may be wired in a series using
an optional daisy chain connector. The table below
shows the maximum number of fixtures that can be
wired together in a series.
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Safety glasses
• Drill with 1/16 in. drill bit
OPTIONAL ITEM
(Purchase separately)
• Splice box
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For indoor use only.
• This product is not intended to be repaired by service personnel, in case of failure
or component defect (unit can be thrown away).
• This product must not be disposed of together with domestic waste. This
product has to be disposed at an authorized place for recycling of electrical
and electronic appliances.
• Read and follow these instructions.
• Risk of fire/electric shock. DO NOT disassemble fixture. The fixture does not have any
user serviceable parts.
• FIXTURE IS NOT WATERPROOF and is not intended for use in showers, saunas, or in
potentially wet locations. ALWAYS keep this fixture away from sinks, tubs, showers, etc.
CAUTION
• This fixture IS ONLY FOR USE ON 110-120V AC circuits.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician.
• This fixture MUST ALWAYS BE USED in accordance with all electrical and safety codes
and ordinances, including the most recent National Electric Code (NEC) and with the
Occupational Safety and Health Administration (OSHA) Volume 1 on General Industry
Standards and Interpretations.
• ALWAYS make certain that the power source conforms to the requirements on
the fixture.
• This fixture is intended for use as general indoor lighting. DO NOT use in potentially
dangerous locations, such as flammable or explosive atmospheres.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation. Under Part 15 of the FCC Rules, any changes or modifications to
the motion detector described in this instruction sheet that are not expressly approved
by Cooper Lighting, LLC could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
ENGLISH
PACKAGING CONTENTS/CONTENIDO DEL PAQUETE
WARNING
A. LED Undercabinet Light
Luz de la parte baja del
gabinete LED
B. (2) Mounting screws
(2) Tornillos de montaje
UNDERCABINET
MASTER SWITCH
HU10MSP (White)
HU10MSMB (Black)
1
A
Wall
Cabinet
front
B