Installation Instructions

ManualsBrandsHalo ManualsLighting6 in. White Integrated LED Recessed Trim Downlight 90 CRI 3000K CCT with Junction Box

SLD6xWH Series Instructions

SLD6xWH Instrucciónes Serie

SLD6xWH Directives Serie

Packaging Contents

Contenu de l’emballage

Contenidos del embalaje

ITEMS REQUIRED

(Purchase separately)

• #2 Philips Screwdriver

• Gloves (if using friction blades)

ARTICLES NÉCESSAIRES

(à acheter séparément)

• Tournevis à tête cruciforme no 2

• Gants (si vous utilisez des lames

de friction)

ARTÍCULOS NECESARIOS

(se compran por separado)

• Destornillador Philips nº 2

• Guantes (si se utiliza las hojas

de fricción)

A. SLD and connector

SLD y conector

SLD et connecteur

D. (2) Torsion Springs

(2) Resortes de torsión

(2) Ressorts de torsion

H. (3) Wire Nuts

(3) Noix de Fil

(3) Tuercas para Alambre

E. (2) Friction Clips

(2) Sujetadores de fricción

(2) Attachee de friction

F. E26 Edison screw base adapter

Adaptador de la base con

roscaEdison E26

L’adaptateur de base Edison E26

C. (2) #6-32 x 7/8 in. and (2) #8-32 x 1 in. junc-

tion box screws (use the size that ﬁts your

junction box)

(2) #8-32 x 1/4 in. self tapping screws

(2) Vis #6-32 x 7/8 et (2) #8-32 x 1 pour

boîte de jonction (utiliser la taille adaptée à

votre boîte de jonction)

(2) Vis de mécanique #8-32 x 1/4

(2) Tornillos #6-32 x 7/8 pulg. y (2) tornillos

#8-32 x 1 pulg. para montaje de la caja de

conexión (utilice el tamaño que mejor se

adecu a su caja de conexión)

(2) Tornillos mecánicos #8-32 x 1/4 pulg.

G. Green ground wire with #8-32 self tapping

screw and #8-32 hex nut

Mise á la terre vert avec vis de méca-nique

#8-32 et écrou hexagonal #8-32

Cable de conexión a tierra verde con

Tornillo mecánico #8-32 y tuerca hexagonal

#8-32

B. Supply Wire Adapter (Required to be

installed onto ﬁxture per instructions)

Fil d’alimentation Adapater (à installer sur le

luminaire conformément aux instructions.)

El cable de suministro Adapater (deben

instalarse en la luminaria conforme a las

instrucciones.)

INS #

706087INSC

Summary of content (10 pages)

PAGE 1
INS # 706087INSC SLD6xWH Series Instructions SLD6xWH Instrucciónes Serie SLD6xWH Directives Serie Packaging Contents Contenu de l’emballage Contenidos del embalaje B. Supply Wire Adapter (Required to be installed onto fixture per instructions) Fil d’alimentation Adapater (à installer sur le luminaire conformément aux instructions.) El cable de suministro Adapater (deben instalarse en la luminaria conforme a las instrucciones.) A. SLD and connector SLD y conector SLD et connecteur E.
PAGE 2
706087INSC IMPORTANT SAFETY INSTRUCTIONS When using product, basic precautions should always be followed, including the following: • Heed all warnings, including below warnings AND those included on product. • HALO recessed housings (fixtures) and retrofits are designed to meet the latest NEC requirements and are UL/cUL listed in full compliance with UL 1598. Before attempting installation of any recessed housing check your local electrical code.
PAGE 3
706087INSC DETERMINING WHICH INSTALLATION METHOD TO USE This module can be mounted to recessed mounted standard junction boxes with junction box bracket or installed into 5 inch and 6 inch recessed housings with torsion spring receivers or with friction clips. WARNING Risk of electric shock. Disconnect power at fuse or circuit breaker before installing or servicing.
PAGE 4
706087INSC screw base recessed housings. The SLD6 is UL Listed and Classified for retrofit in the following housings: The SLD6 is UL Listed or Classified for use with any 5 or 6 inch diameter recessed housing constructed of steel or aluminum with an internal volume that exceeds 107.9 cubic inches in addition to those noted below.
PAGE 5
706087INSC 4. Arrange the supply wire adapter as shown in Figure 5A into the back of the junction box. 5. Align appropriate holes (Fig 4) in the mounting bracket with the holes in the junction box. Using 2 of the longer screws (either #6 or #8 screws depending on the size of the holes in your junction box) attach the mounting bracket to the junction box. Tighten screws until bracket is flush with the ceiling. Do not over-tighten screws or fixture will not be tight to ceiling (Fig. 5).
PAGE 6
706087INSC Mounting to recessed housings Montage sur boîtier encastrés For 5” housings with torsion spring receiving brackets (see HOUSINGS section of these instructions for a listing of the most common housings): 1. Locate the arrow mark on the mounting bracket and the 5 inch arrow mark on the torsion spring clip and align the two marks (Fig. 8). 2. Use one of the provided #8-32 x ¼ in. screws to attach the torsion spring bracket and the green ground wire to the mounting bracket (Fig. 8). 3.
PAGE 7
1 706087INSC For 5” housings without torsion spring receiving brackets (see HOUSINGS section of these instructions for a listing of the most common housings): 1. Attach one of the friction mount clips to the innermost position on the mounting bracket using one of the provided #8-32 x ¼ in. screws (Fig. 10). 2. Repeat step 1 for the second clip but install the green ground wire under the screw. GROUND WIRE ATTACHMENT IN RECESSED HOUSINGS NOTE: Green ground wire must be securely installed to the housing.
PAGE 8
706087INSC SLD INSTALLATION OR RETROFIT INTO E26 EDISON SCREW BASE RECESSED HOUSINGS L’INSTALLATION OU POST-CÂBLAGE INSTALACIÓN DE SLD O ADAPTADOR SLD DANS LES BOÎTIERS ENCASTRÉS À EN UN ALOJAMIENTO EMPOTRADO BASE VISSABLE E26 EDISON EDISON E26 CON BASE ENROSCABLE REMARQUE : Confirmez la compatibilité du boîtier NOTE: Confirm luminiare is compatible with SLD6 module series. A listing of the most common housings is avec le boîtier de module SLD6.
PAGE 9
706087INSC INSTALLATION INTO HALO LED (non-screw base) HOUSINGS H2750x, H550x and H750x SERIES NOTE: May be used to meet California Title 24, Washington State Energy Code, and International Energy Conservation Code High Efficacy Compliance. 1. Ensure bottom edge of housing is flush with ceiling. Adjust height if necessary to ensure a tight finish. 2. Plug orange connector on SLD into the orange connector in housing (Fig. 16). 3.
PAGE 10
706087INSC FORM OF ACTION, WHETHER IN CONTRACT, STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL THE LIABILITY OF COOPER LIGHTING FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR MODIFICATION OF COOPER LIGHTING PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE, EXCEED THE PURCHASE PRICE OF COOPER LIGHTING PRODUCTS GIVING RISE TO A CLAIM.