Installation Sheet

ManualsBrandsHalsey Taylor ManualsShop All Halsey TaylorHalsey Taylor OVL-II Wall Mounted Bi-Level Indoor/Outdoor Water Fountain Coolers - Barrier free with Vandal Resistant Bubbler

Page 1

98953C (Rev. B - 11/16)

HVR8BL(R)*1D HVR8BLWF*1D

Owners Manual

MANUAL DEL PROPIETARIO HALSEY TAYLOR

MANUEL DE L'UTILISATION HALSEY TAYLOR

HVRBL™ Series Vandal-Resistant Water Coolers

Serie HVRBL™ enfriadores de agua a prueba de agresiones

Série HVRBL™ anti-vandalisme refroidisseurs d’eau

Summary of content (7 pages)

PAGE 1
HVR8BL(R)*1D HVR8BLWF*1D MANUAL DEL PROPIETARIO HALSEY TAYLOR MANUEL DE L'UTILISATION HALSEY TAYLOR Owners Manual HVRBL™ Series Vandal-Resistant Water Coolers Serie HVRBL™ enfriadores de agua a prueba de agresiones Série HVRBL™ anti-vandalisme refroidisseurs d’eau Page 1 98953C (Rev.
PAGE 2
HVR8BL(R)*1D HVR8BLWF*1D Note: Danger! Electric shock hazard. Disconnect power before servicing unit. Uses HFC-134A refrigerant 10 12 20 39 7 3 40 41 6 6 16 1 See Fig. 5 16 16 1 See Fig. 5 See Fig. 5 25 27 32 25 21 See Fig. 5 11 27 21 38 33 21 19 32 27 15 37 27 4 8 37 33 21 5 27 FIG. 1 98953C (Rev.
PAGE 3
Page 3 20 3/8" 518mm 2 7/16" 63mm 1 1/2" 38mm 10" 254mm C L 1 3/8" 35mm B 5 3/4" 146mm 1 3/8" 35mm C L 6 1/4" 158mm 3 1/2" 89mm 4 1/2" 114mm 1 3/8" 35mm D A E 25 1/8" 638mm 20 1/8" 511mm 18 3/4" 476mm F 13 7/8" 352mm 5 3/4" 146mm ORIFICE HEIGHT ALTURA DEL ORIFICIO HAUTEUR DE L'ORIFICE F = 7/16 BOLT HOLES FOR FASTENING UNIT TO WALL E = INSURE PROPER VENTILATION BY MAINTAINING 6” (152 mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
PAGE 4
98953C (Rev. B - 11/16) FIG. 3 Page 4 18 3/4" 476mm 13 7/8" 352mm F 6 1/4" 158mm 1 3/8" 35mm 10" 254mm 4 1/2" 114mm 3 1/2" 89mm 1 3/8" 35mm FINISHED FLOOR PISO ACABADO PLANCHER FINI 5" 127mm 1 3/8" 35mm 31 11/16" 804mm 26 11/16" 677mm E 20 3/8" 518mm F A D ORIFICE HEIGHT ALTURA DEL ORIFICIO HAUTEUR DE L'ORIFICE F = 7/16 BOLT HOLES FOR FASTENING UNIT TO WALL E = INSURE PROPER VENTILATION BY MAINTAINING 6” (152 mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
PAGE 5
HVR8BL(R)*1D HVR8BLWF*1D IMPORTANT ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON HANGER BRACKETS & TRAP INSTALLATION 1) Remove hanger bracket fastened to back of cooler by removing one (1) screw. 2) Mount the hanger bracket and trap as shown in Figure 2. NOTE: Hanger Bracket MUST be supported securely. Add fixture support carrier if wall will not provide adequate support. IMPORTANT: • 6 1/4 in. (159mm) dimension from wall to centerline of trap must be maintained for proper fit.
PAGE 6
HVR8BL(R)*1D HVR8BLWF*1D 1 30 14 1 Basin 1 25 23 VANDAL RESISTANT BUBBLER DETAIL 27 (8) 22 22 22 22 1 33 1 40 (LH unit) 41 (RH unit) (Items 31 & 24 also used on the LH unit) 31 24 35 32 17 36 17 18 17 26 28 17 34 13 17 27 (6) 17 29 (4) 28 Fig. 6 (Refrigerated side shown) 28 98953C (Rev.
PAGE 7
HVR8BL(R)*1D HVR8BLWF*1D PARTS LIST/ LISTA DE PIEZAS/ LISTE DES PIÈCES ITEM PART NO. NO. 1 2 3 *4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 NS NS NS 97446C 98777C DESCRIPTION DESCRIPCIÓN Bubbler Assy - VR Kit - Compressor Mtg/Clips/Studs/Grommets Kit - Fan Motor/Blade/Shroud/Nut/Screws 98775C Compressor Serv.