HACFSCWSD*1F HACFSCWSDNF*1F HAC8FSCWSQ*1F, *3F MANUAL DEL PROPIETARIO HALSEY TAYLOR MANUEL DE L'UTILISATION HALSEY TAYLOR HAC8FSCWSNFQ*1F, *2F Owners Manual Hydroboost® Bottle Filling Station and Cooler Estación de llenado de botella Hydroboost® y enfriador Station de remplissage de bouteille Hydroboost® et refroidisseur Page 1 1000001728 (Rev.
HACFSCWSD*1F HACFSCWSDNF*1F HAC8FSCWSQ*1F, *3F HAC8FSCWSNFQ*1F, *2F Note: Danger! Electric shock hazard. Disconnect power before servicing unit. Nota: peligro! Peligro de descarga eléctrica. Desconecte antes de reparar la unidad. Remarque : Danger ! Risque d'électrocution. Débrancher avant de réparer l'appareil. Pictured is unit only without bottle filler. Uses HFC-134A refrigerant Usa refrigerante HFC-134A Utilise du fluide frigorigéne HFC-134A 24 5 3 12 17 22 14 14 13 22 2 10 See Fig.
1" 787mm 25" 635mm Fig.
HACFSCWSD*1F HACFSCWSDNF*1F HAC8FSCWSQ*1F, *3F HAC8FSCWSNFQ*1F, *2F IMPORTANT ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON IMPORTANTE TODO EL SERVICIO DEBERÁ SER EFECTUADO POR UNA PERSONA DE SERVICIO AUTORIZADA IMPORTANT TOUT ENTRETIEN DOIT ÊTRE EFFECTUÉ PAR UN REPRÉSENTANT AUTORISÉ HANGER BRACKETS & TRAP INSTALLATION INSTALACIÓN DE FIJADOR DE SUSPENSIÓN Y DEL PURGADOR INSTALLATION DU SIPHON ET DU SUPPORT DE SUSPENSION 1) Remove hanger bracket fastened to back of cooler by removing
HACFSCWSD*1F HACFSCWSDNF*1F 8 HAC8FSCWSQ*1F, *3F HAC8FSCWSNFQ*1F, *2F PUSH BAR MECHANISM MECANISMO DE BARRA DE EMPUJE MÉCANISME DU BOUTON-POUSSOIR 7 8 28 10 2 1 9 29 A 8 8 9 7 27 8 26 B 8 9 C 9 7 Water Valve Mechanism - ADJUSTMENT PROCEDURE: - Turn adjustment screw “Counter-Clockwise” until water flow from bubbler starts. - Turn adjustment screw “Clockwise” until water flow stops, THEN turn an additional 1/2 turn.
HACFSCWSD*1F HACFSCWSDNF*1F HAC8FSCWSQ*1F, *3F HAC8FSCWSNFQ*1F, *2F MOUNTING SCREWS 7/16” BOLT HOLES FOR FASTENING UNIT TO WALL TOP COVER 35 UNIT CENTER LINE Fig. 6 Fig. 7 Fig. 9 Fig. 8 BRACKET, WASHERS, & SCREWS Bottle Filler Installation Instructions 1) Remove two (2) mounting screws with 5/32” Allen wrench holding top cover to Bottle Filler (See Fig. 9). Remove top cover. Note do not discard mounting screws, they will be needed to reinstall top cover.
HACFSCWSD*1F HACFSCWSDNF*1F HAC8FSCWSQ*1F, *3F HAC8FSCWSNFQ*1F, *2F BF11 - BF12 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE 1) To verify the software program of the control board the unit will need to be shut down and restarted. The chiller (if present) does not need to be shut down and restarted. 2) The units lower panel must be open to access the power cord and wall outlet. 3) Shut down the unit by unplugging the power cord from the wall outlet.
HACFSCWSD*1F HACFSCWSDNF*1F HAC8FSCWSQ*1F, *3F HAC8FSCWSNFQ*1F, *2F WALL MOUNTING PLATE 16 21 BOTTLE FILLING UNIT 4 22 21 Fig. 10 Fig. 11 Fig. 12 220V/240V Detail 36 35 220V PARTS LIST/ 220V LISTA DE PIEZAS/ 220V LISTE DES PIÈCES ITEM NO. *6 12 25 35 36 PART NO. 1000002147 1000002146 0000000245 98751C 98752C 35826C 35827C DESCRIPTION Compressor Serv. Pak (220v/50Hz) Compressor Serv.
HACFSCWSD*1F HACFSCWSDNF*1F HAC8FSCWSQ*1F, *3F Superseal Fitting Assembly Supersello Accesorio de Montaje Superseal Montage Assemblage 3 2 HAC8FSCWSNFQ*1F, *2F 2 Note: Screw the locknut hand tight to seal. Nota: Apriete la mano de la contratuerca para sellar. Remarque : Visser la main de l'écrou de blocage pour assurer l'étanchéité. 1 Fig. 14 FILTER PARTS LIST (See Fig. 13) ITEM NO. PART NO. 1 2 55898C 98926C 3 0000000746 Fig. 13 LISTA DE PIEZAS DEL FILTRO (Vea la Fig.
HACFSCWSD*1F HACFSCWSDNF*1F HAC8FSCWSQ*1F, *3F HAC8FSCWSNFQ*1F, *2F PARTS LIST/ LISTA DE PIEZAS/ LISTE DES PIÈCES ITEM NO.
