Use and Care Manual

ManualsBrandsHalsey Taylor ManualsKitchenHydroBoost Bi-Level BF Vandal Resistant GreenSpec with Bottle Filling Station Refrigerated Drinking Fountain

HVRGRN8BLWS*1C HVRGRN8BLWSNF*1C

1000001740 (Rev. B - 11/14)

Page 1

MANUAL DEL PROPIETARIO HALSEY TAYLOR

MANUEL DE L'UTILISATION HALSEY TAYLOR

Hydroboost Bottle Filling Station and Cooler

Owners Manual

Estación de llenado de botella Hydroboost y enfriador

Station de remplissage de bouteille Hydroboost et refroidisseur

Summary of content (9 pages)

PAGE 1
HVRGRN8BLWS*1C HVRGRN8BLWSNF*1C MANUAL DEL PROPIETARIO HALSEY TAYLOR MANUEL DE L'UTILISATION HALSEY TAYLOR Owners Manual Hydroboost Bottle Filling Station and Cooler Estación de llenado de botella Hydroboost y enfriador Station de remplissage de bouteille Hydroboost et refroidisseur Page 1 1000001740 (Rev.
PAGE 2
HVRGRN8BLWS*1C HVRGRN8BLWSNF*1C Pictured is unit only without bottle filler. USES HFC-134A REFRIGERANT USA REFRIGERANTE HFC-134A UTILISE DU FLUIDE FRIGORIGÈNE HFC-134A 3 24 7 26 5 3 18 26 21 19 19 26 8 25 See Fig. 3 4B 38 12 4A See Fig. 3 19 32 19 7 34 40 21 19 37 35 11 28 33 23 36 29 Fig. 1 1000001740 (Rev.
PAGE 3
STANDARD TWO-LEVEL INSTALLATION Fig. 2 Page 3 5/16" (8mm) DIA.
PAGE 4
HVRGRN8BLWS*1C HVRGRN8BLWSNF*1C IMPORTANT ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON IMPORTANTE TODO EL SERVICIO DEBERÁ SER EFECTUADO POR UNA PERSONA DE SERVICIO AUTORIZADA HANGER BRACKETS & TRAP INSTALLATION INSTALACIÓN DE FIJADOR DE SUSPENSIÓN Y DEL PURGADOR 1) Remove hanger bracket fastened to back of cooler by removing one (1) screw. 2) Mount the hanger bracket and trap as shown in Figure 2 or 3. NOTE: Hanger Bracket MUST be supported securely.
PAGE 5
HVRGRN8BLWS*1C HVRGRN8BLWSNF*1C PUSH BUTTON MECHANISM MECANISMO DE BARRA DE EMPUJE MÉCANISME DU BOUTON-POUSSOIR 31 17 15 13 17 1 32 30 14 2 16 9 Fig. 4 20 20 24 4A 4B 26 25 24 Fig. 5 Fig. 6 Page 5 1000001740 (Rev.
PAGE 6
HVRGRN8BLWS*1C HVRGRN8BLWSNF*1C MOUNTING SCREWS 7/16” BOLT HOLES FOR FASTENING UNIT TO WALL TOP COVER UNIT CENTER LINE Fig. 7 41 Fig. 8 Fig. 9 Fig. 10 Fig. 9 BRACKET, WASHERS, & SCREWS Bottle Filler Installation Instructions 1) Remove two (2) mounting screws with 5/32” Allen wrench holding top cover to Bottle Filler (See Fig. 7). Remove top cover. Note do not discard mounting screws, they will be needed to reinstall top cover. 2) Remove wall mounting plate from Bottle Filler.
PAGE 7
HVRGRN8BLWS*1C HVRGRN8BLWSNF*1C BF11 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE 1) To verify the software program of the control board the unit will need to be shut down and restarted. The chiller (if present) does not need to be shut down and restarted. 2) The units lower panel must be open to access the power cord and wall outlet. 3) Shut down the unit by unplugging the power cord from the wall outlet. 4) Restart the unit by plugging the power cord back into the wall outlet.
PAGE 8
HVRGRN8BLWS*1C HVRGRN8BLWSNF*1C WALL MOUNTING PLATE BOTTLE FILLING UNIT OVERLOAD 3 2 1 COLD CONTROL (WATER) COMPRESSOR C S RELAY M 6 5 3 2 BLK FAN 1 WHT GND Fig. 12 115V Wiring Diagram Diagrama de Cableado de 115 Voltios Schéma de Câblage de 115 Volts Fig. 11 Superseal Fitting Assembly OPERATION OF QUICK CONNECT FITTINGS SIMPLY PUSH IN TUBE TO ATTACH A Note: Screw the locknut hand tight to seal TUBE IS SECURED IN POSITION B C Fig. 14 Fig.
PAGE 9
HVRGRN8BLWS*1C HVRGRN8BLWSNF*1C PARTS LIST/ LISTA DE PIEZAS/ LISTE DES PIÈCES ITEM NO.