Specification Sheet

20 3/8"
518mm
20 7/16"
519mm
19 3/4"
502mm
17 3/8"
441mm
1 3/16"
30mm
1 3/16"
30mm
8 1/8"
206mm
9 3/8"
238mm
1 1/8"
29mm
3"
79mm
18 3/4"
476mm
4"
102mm
FILTER LOCATION
1/4" O.D. TUBE CONNECT
(CHILLER WATER OUTLET)
3/8" O.D. TUBE CONNECT
(CHILLER WATER INLET)
SHUT OFF VALVE BY OTHERS
BACK WALL LINE
12"
305mm
MINIMUM
DEPTH
FINISHED FLOOR
25 1/4"
642mm
27"
682mm
38 7/8"
988mm
2 7/8"
73mm
25 7/8"
658mm
1-1/4" (32MM)
WASTE TUBE
FURNISHED
3 1/2"
89mm
4 1/2"
117mm
1 1/8"
29mm
11"
279mm
ELECTRICAL
INLET
FINISHED FLOOR
DOUBLE STUD OR 3" (76mm)
BETWEEN MOUNTING FRAMES
IF PLACED NEXT TO ANOTHER
FOUNTAIN OR WALL
32 11/16"
831mm
NOTE - NON-REFRIGERATED MODELS
(WITHOUT CHILLER) REQUIRE 8" (203MM)
MINIMUM DEPTH
NOTE: NON-REFRIGERATED
MODELS (WITHOUT CHILLER)
DO NOT INCLUDE LOUVERS
ACTIVATION
SENSOR
40"
1016mm
4 1/2
114mm
18 3/4"
476mm
5 1/8"
130mm
BACK OF WALL TO
BE 12" (305mm)
MIN DEPTH
8"
203mm
TO FLOOR LINE
FLOOR LINE
WOOD OR STEEL FRAME SHOWN
(NOT PROVIDED)
ELECTRICAL INLET
LOCATION ON CHILLER
1"
25mm
CHILLER SHELF
P/N 27638C
HOOK RODS (2)
P/N 101567443730
SCREWS OR BOLTS
(NOT PROVIDED)
5/16" SCREWS OR BOLTS
(10 REQ'D-NOT PROVIDED)
FRAME
MFWS100
DOUBLE STUD OR 3 INCHES (76 mm)
BETWEEN MOUNTING FRAMES
IF PLACED NEXT TO ANOTHER
FOUNTAIN OR WALL
®
Printed in the U.S.A.
MOUNTING INSTRUCTIONS:
Refer to diagrams for rough-in of plumbing. Install
mounting frame into wall per the installation
instructions. Hang fountain panel over the wall
plate assembly. Attach fountains to wall plate
assembly. Water service line and waste line are to
be assembled as required. Final check for leaks
and correct functions of fountain should be made.
(For details see the installation instructions.)
NOTE: A service stop (not included) must be installed at
the fountain inlet line.
NOTE: P-Trap (not supplied) to be installed per local
building code.
NOTE: For wall support required locations see installation
instructions provided with panel and fountains.
CAUTION - Fountain must be securely bolted
to wall.
OPERATING PRESSURES:
Supply water - 105 psi maximum
Minimum 40 psi supply line pressure required in special
circumstances where both sides of bi-level are in use
simultaneously to ensure adequate stream height. Use
of water lter in this situation is not recommended.
ELECTRICAL
Hydroboost
®
station equipped with electric cord and
three-prong molded rubber plug for use with 15-
amp minimum receptacle. For the cooling unit, a
junction box for a (3) wire, 10 amp branch circuit is
provided. Rated at 115 volt, 60 Hz, single phase.
Specications and measurements are subject to change without notication.
Please visit halseytaylor.com for most current version.
Satisfying Thirsts Since 1912
FILTERED
HYDROBOOST™
Job Name: ______________________________
Date: __________________ Qty. ____________
Contact Info (Name, Phone, Email): __________
________________________________________
________________________________________
Approval: _______________________________
TOP & SIDE VIEWS
FRONT VIEW
WALL LAYOUT