PLATINUM PRO PLUG-IN Hyundai Genesis BK Theta HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: PH: 760 598 1941 FAX: 760 598 1987 EMAIL: usa@haltech.com See the Haltech Website for your local authorised dealer. www.haltech.
LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants the Haltech TM Programmable Fuel Injection System to be free from defects in material or workmanship for a period of 12 months from the date of purchase. Proof of purchase, in the form of a bill of sale or receipted invoice, which indicates that the product is within the warranty period, must be presented to obtain warranty service.
Notes PLATINUM Pro Plug-in Hyundai Genesis BK Theta Quick Start Guide Congratulations on purchasing a Haltech Engine Management System. This fully programmable Plug and Play product opens the door to virtually limitless performance modification and tuning of your vehicle. Programmable systems allow you to extract all the performance from your engine by delivering precisely the required amount of fuel and ignition timing that your engine requires for maximum output under all operating conditions.
ECU Installation ECU Pinout To install your new Platinum Pro Plug-in to your Hyundai Genesis, please follow the procedures below. 1. Locate your factory ECU. This will be located in the engine bay, near the firewall on the drivers side. Remove the strut tower brace for easy access. Looking into ECU connector Figure 1 – ECU and strut tower bolts location 2. With the ignition turned off remove the ECU connector from the ECU by lifting the connector levers up and pulling the connectors out.
The Haltech CAN Network 3. Cut the two zip ties that are holding the wiring harness to the plastic junction box and then undo the bolt holding the junction box to the vehicle. The Haltech CAN network allows for simple and effective expansion in ECU capability and functionality without having to go to the trouble of wiring in a whole new computer. Expansion is made possible by the addition of multiple expansion devices that communicate to the main ECU via a Control Area Network (CAN).
5. Remove the two firewall mounted nuts that secure the plastic cover over the top of the wiring harness firewall pass through grommet, once the nuts are removed from the plastic cover it can be removed to access the pass through grommet. Removing the plastic cover can be difficult as there is a metal ring that sits inside the plastic cover and clamps the rubber grommet underneath in place.
. Rear Auxiliary Connector The Platinum Pro Plugin Series allows further expansion of your ECU by the Rear Auxiliary Connector. • • • • • • • The Rear Auxiliary connector allows you access to: 1 Additional Digital Pulsed Input ( DPI ) 2 Additional Digital Pulsed Outputs ( DPO ) 2 Additional Digital Switched Outputs ( DSO ) 4 Additional Analogue Voltage Inputs ( AVI ) 2 Additional +13.
9. Calibration of the Electronic Throttle ECU Manager / ECU Manuals Before trying to start the vehicle the Electronic throttle MUST be calibrated. Calibration of the throttle is achieved by using the Haltech ECU Manager ETC Calibration wizard located in the Advanced Tab within the Main setup page. The process to Calibrate the Electronic Throttle is outlined below.
ECU Manager Software Calibration Steps ECU Manager software is used for setup, calibration and diagnostics and can be found on the CD supplied with this unit or downloaded from the Haltech website www.haltech.
Step 3: Throttle Position Sensor 1 (TPS 1) Release the accelerator pedal to a non-pressed state. Ensure that all electronic throttles are connected and click calibrate to continue Figure 12 – TPS 1 Calibration Success Step 4: Throttle Position Sensor 2 (TPS 2) In Twin throttle applications the Electronic Throttle Calibration wizard will proceed to calibrate the TPS 2 automatically.
Step 3: Throttle Position Sensor 1 (TPS 1) Release the accelerator pedal to a non-pressed state. Ensure that all electronic throttles are connected and click calibrate to continue Figure 12 – TPS 1 Calibration Success Step 4: Throttle Position Sensor 2 (TPS 2) In Twin throttle applications the Electronic Throttle Calibration wizard will proceed to calibrate the TPS 2 automatically.
ECU Manager Software Calibration Steps ECU Manager software is used for setup, calibration and diagnostics and can be found on the CD supplied with this unit or downloaded from the Haltech website www.haltech.
9. Calibration of the Electronic Throttle ECU Manager / ECU Manuals Before trying to start the vehicle the Electronic throttle MUST be calibrated. Calibration of the throttle is achieved by using the Haltech ECU Manager ETC Calibration wizard located in the Advanced Tab within the Main setup page. The process to Calibrate the Electronic Throttle is outlined below.
7. Rear Auxiliary Connector The Platinum Pro Plugin Series allows further expansion of your ECU by the Rear Auxiliary Connector. • • • • • • • The Rear Auxiliary connector allows you access to: 1 Additional Digital Pulsed Input ( DPI ) 2 Additional Digital Pulsed Outputs ( DPO ) 2 Additional Digital Switched Outputs ( DSO ) 4 Additional Analogue Voltage Inputs ( AVI ) 2 Additional +13.
5. Remove the two firewall mounted nuts that secure the plastic cover over the top of the wiring harness firewall pass through grommet, once the nuts are removed from the plastic cover it can be removed to access the pass through grommet. Removing the plastic cover can be difficult as there is a metal ring that sits inside the plastic cover and clamps the rubber grommet underneath in place.
The Haltech CAN Network 3. Cut the two zip ties that are holding the wiring harness to the plastic junction box and then undo the bolt holding the junction box to the vehicle. The Haltech CAN network allows for simple and effective expansion in ECU capability and functionality without having to go to the trouble of wiring in a whole new computer. Expansion is made possible by the addition of multiple expansion devices that communicate to the main ECU via a Control Area Network (CAN).
ECU Installation ECU Pinout To install your new Platinum Pro Plug-in to your Hyundai Genesis, please follow the procedures below. 1. Locate your factory ECU. This will be located in the engine bay, near the firewall on the drivers side. Remove the strut tower brace for easy access. Looking into ECU connector Figure 1 – ECU and strut tower bolts location 2. With the ignition turned off remove the ECU connector from the ECU by lifting the connector levers up and pulling the connectors out.
Notes PLATINUM Pro Plug-in Hyundai Genesis BK Theta Quick Start Guide Congratulations on purchasing a Haltech Engine Management System. This fully programmable Plug and Play product opens the door to virtually limitless performance modification and tuning of your vehicle. Programmable systems allow you to extract all the performance from your engine by delivering precisely the required amount of fuel and ignition timing that your engine requires for maximum output under all operating conditions.
LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants the Haltech TM Programmable Fuel Injection System to be free from defects in material or workmanship for a period of 12 months from the date of purchase. Proof of purchase, in the form of a bill of sale or receipted invoice, which indicates that the product is within the warranty period, must be presented to obtain warranty service.
PLATINUM PRO PLUG-IN Hyundai Genesis BK Theta HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: PH: 760 598 1941 FAX: 760 598 1987 EMAIL: usa@haltech.com See the Haltech Website for your local authorised dealer. www.haltech.
