Instructions / Assembly

ManualsBrandsHamilton Beach ManualsKitchenTop Loading Hot and Cold Water Dispenser with Storage Cabinet

Parts and Features

12 Lift Handle

13 Cold Water (On/Off) Switch (green)

14 Hot Water (On/Off) Switch (red)

4 5

1 Bottle Support Collar

2 Hot Water Button

3 Cold Water Button

4 Hot Water Indicator Light

5 Cold Water Indicator Light

6 Spigot

7 Removable Drip Tray and Insert

8 Bottom Door and Storage Cabinet

9 Water Outlet (drain valve)

10 Condensor Coils

11 Child Safety Lock

Proper Installation and Location

• This dispenser is for indoor use only. Do not use outdoors.

• Place the dispenser on a level surface that can support its weight with a

full water bottle installed.

• To ensure that your water dispenser works at the maximum efficiency,

leave at least 2 inches (5 cm) of clearance between all sides of the

dispenser and any walls.

• To prevent damage to the dispenser, do not plug dispenser into the

power outlet until reading the instructions first!

Preparing, Loading and Operating Your

Dispenser

For use with 3 or 5 gal. (12 or 19L) water bottles.

DO NOT PLUG IN POWER CORD UNTIL WATER BOTTLE IS LOADED!

IMPORTANT: Always wash your hands before handling water bottle.

Clean the top of the water bottle with a damp cloth.

1. Make sure that the dispenser is not plugged into the electrical outlet.

2. Load the water bottle onto the dispenser. The water bottle will have a

cap. The cap may have a stopper that is intended to be pushed into the

bottle. (Sometimes these stoppers are covered by a removable paper/

foil seal.) If your bottle has a cap with a stopper, simply hold the water

bottle vertically straight upside down and place the water bottle into the

support collar on top of the water dispenser. The post in the Bottle

Support Collar (see # 1 on the Parts and Features list) will push the

stopper into the bottle. For bottles that don’t have a cap, quickly turn

bottle vertically and place into Bottle Support Collar.

3. Once the reservoirs have filled, draw some water out of the Spigot (see

# 6 on the Parts and Features list) using the Hot and Cold Water Buttons

(see # 2 and 3 on the Parts and Features list). If water flows out from

both buttons, continue onto the next step. If water doesn’t flow from

each button, stop use and call Customer Service.

4. Plug the dispenser into the outlet.

Grounding Instructions

WARNING: Modifying or defeating of the grounding plug can result in a

risk of electric shock.

• This appliance must be grounded. In the event of an electrical

short circuit, grounding reduces the risk of electric shock.

• This appliance is equipped with a power cord that has a grounding

wire with a grounding plug. The plug must be plugged into a 3 prong

outlet that is properly installed and grounded.

• Consult a qualified electrician if the grounding instructions are not

completely understood, or if doubt exists as to whether the

appliance is properly grounded.

• Do not under any circumstances cut or remove the third ground

prong from the power cord.

• Do not use an extension cord with this appliance. If the power cord is

too short, have a qualified electrician install an outlet near the desired

location of the unit.

• For best operation, plug the appliance securely into its own electrical

outlet on a dedicated circuit not shared with any other appliances to

prevent blowing a fuse or tripping the circuit breaker.

Getting familiar with your Hamilton Beach

Water Dispenser

Features

• Designed for in-home or office use.

• Fits 3 or 5 gallon bottles.

• Two high-flow water dispensing buttons: Red for hot water and Blue

for cold water.

• Compact space saver design with lower storage cabinet.

• Energy Saver switches located on the left side of the appliance (see #

13 and 14 on the Parts and Features list). Turn the RED switch to the OFF

position to stop heating and turn the GREEN switch to the OFF position to

stop cooling.

Draining the Reservoirs

Drain the reservoirs before and after cleaning, before long vacations or if

not using the dispenser for a long period of time.

1. Unplug the dispenser and let it sit for 1 hour.

2. Using the Hot and Cold Water Buttons (see # 2 and 3 on the Parts and

Features list), empty any remaining water from the bottle and remove

the bottle from the dispenser.

3. Place a container under the Spigot (see # 6 on the Parts and Features

list). Press and hold the Hot and Cold Water Buttons until water no

longer comes out of the Spigot.

4. Place a container directly under the Water Outlet (drain valve) on

the back of the dispenser (see # 9 on the Parts and Features list).

5. Remove the drain valve cap and drain valve plug and let the water

flow into the container until no more water comes out. Tilt the unit

back on an angle to remove any last drips from the Water Outlet

(drain valve).

Note: Water coming from the drain plug may be hot. Let unit stand

unplugged for 1 hour before removing drain plug and draining

the water.

6. Replace the drain valve cap and drain valve plug.

7. Install a new water bottle.

8. Plug in the dispenser.

Congratulations, you have acquired a high quality Hamilton Beach™ Water

Dispenser for bottled water. This product allows you to enjoy a cool drink

or a hot beverage and has many features that you will find convenient to

use. Please record the model number, serial number, and the manufacture

date which can be found on the label on the back of the unit.

____________________________________________________________________

model number serial number manufacture date date of purchase

READ ALL INSTRUCTIONS BEFORE USING!

SAVE THIS MANUAL FOR FUTURE USE!

No product registration is required for this unit. When making a customer

service call, please have the model number, manufacture date, and serial

number (6 digit number on the Energy Star Label) on hand.

CUSTOMER SERVICE: 716-235-1300

Toll-Free 1-800-256-8169

Problem

No hot or cold

water.

No water

dispenses

from spigot.

Water

dispenser

leaks from the

outside.

Water has

poor taste or

odor.

Water

dispenser

does not work.

Possible Causes

1. Dispenser is

unplugged.

2. The fuse is

blown/circuit

breaker is tripped.

3. Energy saver

switches are not

turned on.

1. Water bottle is

empty.

2. Inlet of Bottle

Support Collar is

blocked by bottle

seal.

3. Mineral deposits

clogging tank.

1. Minor dent,

depression, crack or

pin hole in water

bottle.

1. Tank needs to be

cleaned or sanitized.

1. Empty water bottle.

2. Mineral deposits are

clogging tank.

Solution

1. Push plug completely

into outlet.

2a. Replace fuse or reset

circuit breaker.

2b. If too many items are

plugged into a single

circuit, move some

items to a different plug.

3. Turn energy saver

switches on the back of

the unit to the ON

position.

1. Replace with new bottle.

2. Remove water bottle

and check inlet. Clean

out waste paper and

insert bottle again.

3. See “To Remove Mineral

Deposits” instructions.

1. Replace with new bottle.

1. See “Sanitizing and

Cleaning” instructions.

1. Replace with new bottle.

2. See “To Remove Mineral

Deposits” instructions.

Top-Loading Water Dispenser

Instruction Manual

To ensure proper use and for your safety, please read the following

instructions completely before operating this appliance.

TL Series

IMPORTANT SAFEGUARDS

• When using electrical appliances, basic safety precautions should be

followed, including the following:

• WARNING: BURN HAZARD. The product heats water to a temperature

of approximately 95° C / 203° F. Water temperatures above 52° C / 125° F

can cause severe burns or death from scalding. Children should be

supervised by an adult when using this product.

• WARNING: FIRE HAZARD. Do not store or use gasoline or other

flammable vapors and liquids in the vicinity of this or any other appliance.

Do not operate the dispenser with a damaged cord. Do not use with an

underrated extension cord or an extension cord without a ground.

• WARNING: SHOCK HAZARD. Unplug the water dispenser before

cleaning or wiping up spilled water on unit. Do not attempt to service

the dispenser. Do not operate dispenser with a damaged cord.

• Never turn the product upside down or tilt more than 45 degrees. If the

unit has been resting on its side for a long period of time, you must

position the water cooler in the upright position for approximately 12

hours before turning it on.

• Never use this dispenser with water that is unsafe to drink or is from an

unknown source.

• Never use any other liquid in this dispenser than bottled water.

• Install this water dispenser in a dry place away from direct sunlight. For

indoor use only.

• Never put anything flammable close to the dispenser.

• Leave a minimum of 2” (5 cm) around the back and sides of the

dispenser for proper ventilation.

• Regular cleaning of the water dispenser is required for proper operation.

Clean the dispenser every four months using the instructions in this

manual.

• Never plug the unit in without water inside. If the bottle becomes

empty, turn the Hot Water (On/Off) Switch (see # 14 on the Parts and

Features list) to the OFF position, and then install a new bottle.

SAVE THESE INSTRUCTIONS!

5. Turn on the HOT and COLD water switches (see # 12 and 13 on the

Parts and Features list). The HOT and COLD indicator lights (see # 4

and 5 on the Parts and Features list) will turn on.

6. Allow up to 30 minutes for the Heating and Cooling cycles to

complete. When the indicator lights turn off, the unit is ready to

dispense HOT and COLD water.

WARNING: BURN HAZARD. The product heats water to a temperature of

approximately 95° C / 203° F. Water temperatures above 52° C / 125° F can

cause severe burns or death from scalding. Children should be supervised

by an adult when using this product.

7. The hot water temperature is preset to

95° C / 203° F. The Hot Water Button

(see # 2 on the Parts and Features list) is

equipped with a Child Safety Lock (see #

11 on the Parts and Features list) that

reduces the risk of hot water being

dispensed accidentally or by small children.

8. Place a glass on top of the Removable Drip Tray and Insert (see # 7 on

the Parts and Features list) and underneath the Spigot (see # 6 on the

Parts and Features list).

9. To dispense cold water, depress the Cold Water Button (see #3 on the

Parts and Features list).

10. To dispense hot water, slide the red Child Safety Lock (see #11 on the

Parts and Features list) to the side, then depress the Hot Water Button

(see #2 on the Parts and Features list).

11. When the water bottle is empty, remove it by pulling it vertically up and

out using two hands, and then replace it with another bottle.

Proper Care and Cleaning of the Dispenser

• To maintain maximum efficiency and to prevent bacterial growth in the

water dispenser, we strongly recommend cleaning every 4 months.

Cleaning the Outside of the Dispenser

• Make sure the unit is unplugged before attempting to clean.

• Wipe the outside of the dispenser with a mild soap and water

mixture. Never use harsh chemicals or abrasive cleaners. Rinse

thoroughly with clean water and dry all surfaces.

• Do not immerse in water.

Cleaning the Removable Drip Tray and Grate

• The Removable Drip Tray and Insert (see # 7 on the Parts and Features

list) should be emptied and cleaned regularly to remove spotting and

mineral deposits.

1. To remove the Drip Tray (see # 7 on the parts and features list) pull the

tray to dislodge it from the guides. Drain and clean.

2. Use a mild soap and water mixture.

For tough deposits add vinegar and let

soak until the deposits come loose.

Then wash, rinse and dry thoroughly.

3. To replace the Drip Tray, put the Insert

back on the tray and slide the

tray on to the guides.

NOTE: The Removable Drip Tray and Insert

are not dishwasher safe.

Cleaning the Condenser

• To improve cooling and efficiency, vacuum or sweep away the dust

from the Condenser Coils (see # 10 on the Parts and Features list) on

the back of the dispenser. You can purchase a brush designed

specifically for this purpose from your local appliance store.

Sanitizing and Cleaning Water Tanks

Important: Periodically the water dispenser tanks must be sanitized to

prevent unpleasant tastes in the water and cleaned to remove mineral

deposits that can impair flow.

1. Using a clean container, premix 2.5 ml / 1/2 teaspoon of ordinary 6.0%

maximum household bleach to a 2 liter / 2 quart pitcher filled

with tap water. Pour the solution into the opening at the top of

the dispenser.

2. Repeat the previous step until the dispenser is full.

3. Press the Hot and Cold Water Buttons (see # 2 and 3

on the Parts and Features list) until the water begins to

flow from the Spigot. Allow the cleaning solution to sit

inside the dispenser for 20 minutes.

3. Place a 1 gallon jug container under the Spigot and

press the Hot and Cold Water Buttons until the cleaning

solution stops flowing. Discard cleaning solution.

4. Using a container, drain the remaining cleaning solution

from the internal reservoirs at the Water Outlet (drain

valve) by unscrewing the drain cap and removing the

drain plug located on the back of the unit.

5. Flush the system using 0.5 gal / 2L clean water using

the same procedure outlined in steps 1 through 4

above. When the rinse water stops flowing, reinstall

the Water Outlet drain plug and drain cap and tighten.

The sanitizing and cleaning process is now complete.

To Remove Mineral Deposits

To remove mineral deposits, follow the instructions for Sanitizing and

Cleaning the Water Tanks, substituting either 2 liters / 2 quarts of water

mixed with 2 liters / 2 quarts of vinegar OR 4 liters / 1 gallon of water

mixed with 454 grams / 16 ounces of citric acid crystals. Bleach does not

remove mineral deposits.

Troubleshooting the Water Dispenser

PRS Enterprises

3349 Monroe Ave., Suite 328

Rochester, NY 14618

Ver. 1.0

Hamilton Beach® is a registered trademark

of Hamilton Beach, Inc. used under license

by PRS Enterprises.

SAVE THESE INSTRUCTIONS!

LIMITED WARRANTY

This warranty applies to products purchased and used in the US and Canada. This

is the only express warranty for this product and is in lieu of any other warranty or

condition.

This product is warranted to be free from defects in materials and workmanship for

a period of one (1) year from the date of original purchase. During this period, your

exclusive remedy is replacement of this product or any component found to be

defective at our option; however, you are responsible for all costs associated with

returning the product to us and our returning a product or component under this

warranty to you. If the product or component is no longer available, we will replace

with a similar one of equal or greater value.

This warranty does not cover glass, filters, wear from normal use, use not in

conformity with the printed directions, or damage to the product resulting from

accident, alteration, abuse, or misuse. This warranty extends only to the original

consumer purchaser or gift recipient. Keep your original sales receipt, as proof of

purchase is required to make a warranty claim. This warranty is void if the product

is used for other than single - family household use or subjected to any voltage and

waveform other than as specified on the rating label (e.g., 115V ~ 60 Hz).

We exclude all claims for special, incidental and consequential damages caused by

breach of express or implied warranty. All liability is limited to the amount of the

purchase price. Every implied warranty, including any statutory warranty or

condition of marchantability or fitness for a particular purpose, is disclaimed

except to the extent prohibited by law, in which case such warranty or condition

is limited to the duration of this written warranty. This warranty gives you specific

legal rights. You may have other legal rights that vary depending on where you live.

Some states or provinces do not allow limitations on implied warranties or special,

incidental, or consequential damages, so the foregoing limitations may not apply to

you.

To make a warranty claim, do not return this appliance to the store. Please call

1.800.256.8169 or 716.235.1300 in the U.S. and Canada or visit hamiltonbeach.com

in the U.S, or hamiltonbeach.ca in Canada. For faster service, locate the model,

type, and series number is on your appliance.

Slide Child Safety Lock to

the left then push button.

1. 2.

1 2 3 4 5

6 7 8 9 10