Operating Instructions

ManualsBrandsHamilton Bonaduz ManualsElectronicsSensor for measurement of dissolved oxygen (DO) and oxygen in gas phase

Table Of Contents

3Operating Instructions VisiFerm

™

mA Sensors

Table of Contents

1 General Information ..................................................4

1.1 Intended Use ................................................................4

1.2 About this Operating Instruction ...................................4

2 Liability .......................................................................4

3 Safety Precautions and Hazards .............................5

3.1 General Precautions ..................................................... 5

3.2 Operation of VisiFerm mA Sensor ................................5

3.3 Instructions for Use in Potentially

Explosive Atmospheres ................................................ 7

3.3.1 General Conditions for Safe Operation ..............7

3.3.2 Earthing .............................................................9

3.4 Electrical Safety Precautions ...................................... 10

3.5 Chemical, Radioactive or Biological Hazard

Precautions ................................................................ 11

4 Product Description ................................................11

4.1 General Description .................................................... 11

4.2 Hardware Description ................................................. 12

4.3 Optical DO measurement ........................................... 13

4.4 VisiFerm mA with Micro-Transmitter inside ................. 13

5 Installation................................................................13

5.1 Unpacking .................................................................. 13

5.2 Configuring the VisiFerm mA with ArcAir

Application .................................................................. 14

5.2.1 Installing ArcAir Basic on the Computer .......... 14

5.2.2 Connecting the VisiFerm mA Sensor

to ArcAir ........................................................... 14

5.2.3 Create User Accounts ...................................... 15

5.2.4 Configuring the VisiFerm mA Sensor

Parameters ...................................................... 15

5.2.5 Configuring the calibration settings .................. 16

5.2.6 Configuring the temperature settings

of SIP / CIP process ........................................ 17

5.2.7 Configuring the analog interface for

your process control system ............................ 17

5.2.8 Defining a measuring point name for

identification of the process ............................. 18

5.3 Install VisiFerm mA in your Measuring Loop ............... 18

5.3.1 Mechanical Process Connection .................... 18

5.3.2 M12 Pin Designation ........................................ 18

5.3.3 Required Power Supply .................................. 19

5.3.4 Electrical Connection for HART

Communication ...............................................19

5.3.5 Electrical Connection for Analog

4-20mA Communication..................................20

6 Operation .................................................................21

7 Maintenance ........................................................... 22

7.1 Verify Sensor Status and ODO Cap Functionality ......22

7.2 Replacing the ODO Cap .............................................23

7.3 Calibration ..................................................................23

7.3.1 Automatic Standard Calibration

with ArcAir .......................................................23

7.3.2 Calibration in Air (Calibration Point Air) ............. 24

7.3.3 Zero Point Calibration (Point Zero Oxygen) ......24

7.4 Product calibration .....................................................25

7.5 Cleaning .....................................................................26

8 Troubleshooting .......................................................27

8.1 Sensor Self-Diagnostic ............................................... 27

8.1.1 Wa r n i ng s .......................................................... 27

8.1.2 Erro r s ...............................................................28

8.2 Getting Technical Support ..........................................29

8.3 Returning VisiFerm mA for Repair ..............................29

9 Disposal .................................................................. 29

10 Bluetooth Certification ........................................... 29

11 Ordering Information .............................................. 30

11.1 VisiFerm mA ...............................................................30

11.2 Parts and Accessories ...............................................32

11.3 Arc Services ...............................................................35

TABLE OF CONTENTSTABLE OF CONTENTS

Hamilton Warranty

Please refer to the General Terms of Sales (GTS).

Important note

part of this document in any form is forbidden without the

express written agreement of Hamilton Bonaduz AG.

Contents of this document can be modified without previous

announcement. Technical modifications reserved. Greatest

possible care was used on the correctness of the

information in this document. If errors should be discov-

ered nevertheless, Hamilton Bonaduz AG is pleased to be

informed about it. Regardless of this, Hamilton Bonaduz AG

cannot assume liability for any errors in this manual or for

their consequences.