Installation Sheet

Included Components
Assembly Instructions
Step 5: Attach glass to braided fabric
cord.
If Gem or Hedra Pendant:
Tighten set screws to hold glass in
place.
If Parallel Glass Pendant:
Install glass panels by
unscrewing the cylinder knobs until
glass can be slid into housing.
Note that the cylinder knobs do not
have to be fully removed from the
fixture to install glass panels.
Tighten the cylinder knobs, ensuring
that the all thread passes through the
glass panels.
If Ledgestone Pendant:
Use 8-32 nylon tip set screws to retain
blown glass.
If Axis Pendant:
Slide glass along retention screws
using slot in glass. Slide pendant
cover over glass and tighten finial until
snug.
A. Hardware Packet R, with Instructions
B. Parallel Glass Panels (QTY:16) or Glass Gems (QTY:8)
C. Canopy
D. Braided Fabric Cord (QTY:8)
E. Cord grip (QTY:8 — Attached to canopy)
F. Set Screws (QTY:24)
G. Cylinder Knobs (QTY: 4)
Step 3: Make Wire Connections to each of the drivers,
mounted inside of the canopy. Using the two installed terminal
blocks make the following connections. Each driver will be
wired in series with 4 pendants. Braided fabric cord must be
wired to the Driver, Black to Black and White to Red. Make
wire connections from driver to supply. White to white, black
to black, and ground the fixture to the canopy.
WARNING
DO NOT DIRECTLY CONNECT LEDs TO AC
POWER. LEDs will be damaged if exposed to high voltages.
The LED’s must be wired in series to work properly.
LEDs run on low voltage, DC electricity. Standard housing
outlets supply high voltage AC electricity; therefore, ensure
the driver is used when connecting LEDs to a power supply.
1. Allen Key (provided)
2. Philips screw driver (not provided)
3. Wire cutters/strippers (not provided)
4. Measuring tape (not provided)
Required Tools
Step 1: Feed the braided fabric cord into the canopy until the
desired amount of cord is left between the canopy and light
body. Take into account that a minimum of 6” of cord will be
required for connecting the wiring to the driver.
Step 2: Use the measuring tape to be sure that all of your light
body is hanging the proper distance from the canopy. Tighten
the cord grip using a flat blade screw driver. The cord grip is on
the face of the canopy. DO NOT OVER TIGHTEN. THIS
MAY DAMAGE THE FIXTURE.
Step 4: Mount the canopy to the ceiling
using the provided Mounting
Instructions.
Parallel
Blown Glass Pendant
Canopy
Braided
Fabric
Cord
Blown
Glass
(Gem shown)
Canopy
Braided
Fabric
Cord
Parallel
Glass
Panel
Ledgestone
Axis Blossom
Blossom Pendant:
Screw glass element into threaded
pendant housing
If Nebula Pendant: Screw inner glass
into socket. Un-Screw Glass Reten-
tion nut. Raise the Top Glass Reten-
tion Cap up the stem. Slide Glass
Shade over inner glass, tilt to the side
of the glass allowing the Bottom Glass
Retention to slip inside the Glass
Shade, slide the rest of the Bottom
Glass Retention the rest of the way
into the Glass Shade, Allow the Glass
to sit on the top of the lips of the
Bottom Glass Retention. Lower the
Top Glass Retention Cap, center the
fixture on the Bottom Glass Retention
and Secure Retention Nut.
(NOTE: Tighten till Snug. DO NOT
Overtighten!)
Nebula
LED 1 Black
LED 2 Black
LED 3 Black
Driver Red
LED 4 Black
LED 1 White
Driver Black
LED 2 White
LED 3 White
LED 4 White
LED 5 Black
LED 6 Black
LED 7 Black
Driver Red
LED 8 Black
LED 5 White
Driver Black
LED 6 White
LED 7 White
LED 8 White
EBR020U-0500-42