Installation Sheet

Included Components
Assembly Instructions
A. Hardware Packet W, with Instructions
B. Parallel Glass Panels (QTY:10) or Blown Glass (QTY:5)
C. Canopy
D. Braided Fabric Cord (QTY:5)
E. Cord grip (QTY:5 — Attached to canopy)
F. If Blown Glass (Set Screws, QTY:10)
G. If Parallel Glass (All Thread & Cylinder Knobs QTY: 20)
H. If Ledgestone Glass (Set Screws, QTY: 20)
Step 3: Make Wire Connections to the drivers, mounted inside
of the canopy. The EBR020U-0500-42 driver will be wired in
series with 4 pendants. The ESS010W-0500-12 driver will be
wired with 1 pendant. Braided fabric cord must be wired to the
Driver, black to black and white to red. To wire in series
make the following connections:
WARNING
DO NOT DIRECTLY CONNECT LEDs TO AC
POWER. LEDs will be damaged if exposed to high voltages.
The LED’s must be wired in series to work properly.
1. Allen Key (provided)
2. Philips screw driver (not provided)
3. Wire cutters/strippers (not provided)
4. Measuring tape (not provided)
Required Tools
Step 1: Feed the braided fabric cord into the canopy until the
desired amount of cord is left between the canopy and light
body. Take into account that a minimum of 6” of cord will be
required for connecting the wiring to the driver.
Step 2: Use the measuring tape to be sure that all of the light
bodies are hanging the proper distance from the canopy. Tighten
the cord grip using a flat blade screw driver. The cord grip is on
the face of the canopy. DO NOT OVER TIGHTEN. THIS
MAY DAMAGE THE FIXTURE.
Step 5: Mount the canopy to the ceiling using the provided
Mounting Instructions.
Canopy
Braided
Fabric
Cord
Blown
Glass
(Aalto shown)
Canopy
Braided
Fabric
Cord
Parallel
Glass
Panel
Step 4: Make wire connections from driver to supply. White to
white, black to black, and ground the fixture to the canopy.
Wiring of Four Pendants
EBR020U-0500-42
Wiring of One Pendant
ESS010W-0500-12
ERP Driver
ESS
Step 6: Attach glass to LED pendant housing:
Gem, Hedra, Rock Crystal, or Aalto Pendant:
Use #4-40 flat head screws provided to attach glass to pendant
housing.
Gem
Aalto
Rock Crystal
Hedra
Parallel
Parallel Glass Pendent:
Install glass panels by
unscrewing the cylinder knobs
until glass can be slid into
housing.
Note that the cylinder knobs do
not have to be fully removed
from the fixture to install glass
panels.
Tighten the cylinder knobs,
ensuring that the all thread
passes through the glass panels.
Ledgestone Pendant:
Use #8-32 nylon tip set
screws to retain blown
glass
Ledgestone
If Axis Pendant:
Slide glass along
retention screws using
slot in glass. Slide
pendant cover over glass
and tighten finial until
snug.
Axis Blossom
Blossom Pendant:
Screw glass element into threaded
pendant housing
NOTE: The Grey and Purple wires are used for 0-10V dim-
ming. If not applicable cap wires. Wires must be capped sepa-
rately, or pendant will dim to zero.
Nebula
If Nebula Pendant: Screw
inner glass into socket. Un-Screw
Glass Retention nut. Raise the Top
Glass Retention Cap up the stem.
Slide Glass Shade over inner glass,
tilt to the side of the glass allowing
the Bottom Glass Retention to slip
inside the Glass Shade, slide the
rest of the Bottom Glass Retention
the rest of the way into the Glass
Shade, Allow the Glass to sit on
the top of the lips of the Bottom
Glass Retention. Lower the Top
Glass Retention Cap, center the
fixture on the Bottom Glass Reten-
tion and Secure Retention Nut.
(NOTE: Tighten till Snug. DO
NOT Overtighten!)
LED 1 Black
LED 2 Black
LED 3 Black
Driver Red
LED 4 Black
LED 1 White
Driver Black
LED 2 White
LED 3 White
LED 4 White
Both drivers will come wired
as shown below, simply plug
in your ac power source.