Innovative Sound Systems Model 3300 Owner’s Manual
IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Keep these instructions. Heed all warnings. Only use attachments/accessories specified by the manufacturer. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings.
FOR UNITED KINGDOM: FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY This appliance is supplied with a molded 3-pin mains plug for your safety and convenience. The plug contains a 5 amp fuse. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BSI1362. Check for the ASTA mark or the BSI mark on the body of the fuse.
THANK YOU! 4 We greatly appreciate your purchase of a new Leslie speaker system. If this is your first purchase of a Leslie product, we would like to welcome you into the Leslie family. If you are a repeat customer, thank you for your continued confidence in our Leslie products. Your new Leslie speaker system was engineered and manufactured to the most stringent-quality standards, reproducing the full-spectrum sound of musical instruments and housed in acousticallyengineered cabinet.
SPECIFICATIONS TYPE LED 1-channel (Rotary Channel Only) Real 2-Rotor 5 Fast, Slow, Stop CONNECTORS POWER OUTPUT Leslie 11-Pin Socket with Stationary L,R through Output, Leslie 8-Pin, Line Input ¼”, imped. 10kΩ sensitivity 100mV (-18dBu), Line Out / Sub Woofer Out 0dBu, Foot Switch (Slow/Fast/Stop) AC Input Horn Rotor 80Wrms Drum Rotor 220Wrms (total power 300Wrms) POWER CONSUMPTION SPEAKER 210W DIMENSION Rotary Horn Driver Ferro-Fluid 63(W) x 52(D) x 90(H) cm 24.8(W) x 20.5(D) x 35.
NAMES AND FUNCTIONS 1 7 8 6 5 4 2 3 FRONT 1. Horn Rotor (built-in) This rotor reproduces the treble sounds. 2. Drum Rotor (built-in) This rotor reproduces the bass sounds. 3. Casters The casters located on the front of this Leslie should be locked during a performance and unlocked when transporting the Leslie. POWER PANEL 4. POWER Switch This switch is used for switching ON/OFF the power on the Leslie 3300.
9 10 11 12 19 21 23 25 20 22 24 26 13 14 15 16 17 28 27 18 29 INDICATOR and JACKS TRIMMERS The Trimmers controls are used to fine adjustments of the turning characteristics of each rotor. Use a flat blade screwdriver with the width of 2.5 to 3 mm to make these adjustments. 19. HORN ROTOR RISE TIME Trimmer 27. ROTOR MODE Indicator These LED’s indicates the current mode of the Rotor. Usually one of FAST, SLOW, or STOP LED’s lights up when the power is ON. 20.
HOOK-UP AND LESLIE SETUP PROCEDURES SINGLE CHANNEL HOOK-UP WITH AN 11-PIN LESLIE SOCKET Applicable HAMMOND Models: New B-3, New C-3, B-3P, B-3M (Ultimo), XK-3 (NOTE 1), XK-2, XB-2, XB-5 NOTE 1: The default setting of the XK-3 is for 1 channel. Steps: 1. 2. 3. 4. Switch OFF the Power of the Organ. Switch OFF (REMOTE) of the Power on the Leslie 3300. Connect the optional 11-pin Leslie cable as shown above.
SINGLE CHANNEL HOOK-UP WITH AN 8-PIN LESLIE JACK Applicable HAMMOND Models: XB-1, XK-1, XM-1, XM-2 Steps: 1. Connect the optional Leslie 8-pin Cable (LC8-7M) as shown above. 2. Set the VOLUME control on the Leslie 3300 to the 3 position. 3. Turn the Power switch on the organ to the ON position. 4. Turn the Power switch on the Leslie 3300 to the ON position. NOTE: The Remote mode does not function when the 8-Pin Cable is used. 5. Switch the Leslie speed switch on the organ from Slow to Fast.
ADVANCED OPERATION Controlling the Overdrive depth of the Leslie 3300 from an Organ. For this example we used an XK-3. Factory set positions for the Trimmer Controls 1. Set the MASTER VOLUME control on the XK-3 to the middle or center position and fully depress the Expression Pedal if one is connected. 2. Set the TUBE MODE control of the Leslie to the middle position and turn the TUBE DRIVE LEVEL control fully counterclockwise (TUBE OFF). RISE TIME FALL TIME 3.
Resetting Rotation Speed to Factory Settings 11 To reset the rotation speed to the factory settings, perform the following procedure: 1 To start the adjusting program, plug the Foot Switch into the FOOT SW jack. Press and hold the Foot Switch while turning ON the power to the Leslie. Continue to hold this switch down until the STOP LED starts blinking to the speed of the rotor (about 4 seconds).
SERVICE 12 Hammond maintains a policy of continuously improving and upgrading its instruments and therefore reserves the right to change specifications without notice. Although every attempt has been made to insure the accuracy of the descriptive contents of this Manual, total accuracy cannot be guaranteed. Should the owner require further assistance, inquiries should first be made to your Authorized Hammond Dealer.
