65 474 Glendale 52 in Ceiling Fan Owner’s Manual Glendale Ventilador de Techo de 1,32 m Manual del Propietario
52” Glendale Thank you for purchasing our ceiling fan. This product has been manufactured with the highest standards of safety and quality. Ceiling Fan by Hampton Bay Date Purchased Table of Contents Store Purchased Safety Rules . . . . . . . . . . . . . . . . . . . . 1 UL Model No. 165-474 Unpacking Your Fan . . . . . . . . . . . . . . 2 Installing Your Fan . . . . . . . . . . . . . . . 3 Serial No. Installing the Light Kit. . . . . . . . . . . . .11 Operating Your Fan . . . . . . . . . . . . . .
Safety Rules – Read and Save These Instructions 1. To reduce the risk of electric shock, insure electricity has been turned off 10. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be at the circuit breaker or fuse box before beginning. spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and ungrounded conductor on the 2.
Unpacking Your Fan Unpack your fan and check the contents. You should have the following items: 4 6 2 5 7 Set of blades (5) 6. Light kit 2. Canopy assembly 7. Glass shades (3) 3. Ball/downrod assembly 8. 13 Watt compact fluorescent bulbs (3) 4. Fan motor assembly 9. Pull chain and fobs (2) 5. Set of blade arms (5) 2 C D 9 1. WARNING DO NOT INSTALL OR USE FAN IF ANY PART IS DAMAGED OR MISSING. CALL TOLL FREE 1-877-902-5588. B 8 1 3 A A.
Installing Your Fan Tools Required Provide Strong Support Figures 1~3 are examples of different ways to mount the outlet box. Phillips screwdriver, straight slot screwdriver, step ladder and wire cutters. Recessed Outlet Box Ceiling Mounting Plate Figure 3 Mounting Options Outlet Box If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers.
Hanging the Fan REMEMBER to turn off the power. Follow the steps below to hang your fan properly. NOTE: This ceiling fan is supplied with two types of hanging assemblies; the standard ceiling installation using the downrod with ball and socket mounting, and the "close-to-ceiling" mounting. The "close-to-ceiling" mounting is recommended in rooms with less than 8-foot ceilings or in areas where additional space is desired from the floor to the fan blades.
Option 2: Close-to-Ceiling Mounting 1. Remove the canopy ring from the canopy. (Figure 5) 2. Remove the mounting bracket from the canopy by loosening the four screws on the top of the canopy. Remove the two non-slotted screws and loosen the slotted screws (Figure 6). 5. Place the rubber gasket over the remaining three screws, route the wires exiting the top of the fan motor through the canopy ring (make sure the slot openings are on top).
Installing Fan to the Electrical Box UL Listed Outlet Box Hook Tab WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL INJURY. MOUNT FAN ONLY TO AN OUTLET BOX OR SUPPORTING SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT AND USE THE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX. 1. Pass the 120-volt supply wires through the center hole in the ceiling mounting bracket as shown in Figure 11.
If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan. Secure the connectors with electrical tape. Make sure there are no loose strands or connections. 1.
Finishing the Fan Installation Standard Ceiling Mounting WARNING LOCKING SLOTS OF CEILING CANOPY ARE PROVIDED ONLY AS AN AID TO MOUNTING. DO NOT LEAVE FAN ASSEMBLY UNATTENDED UNTIL ALL FOUR CANOPY SCREWS ARE ENGAGED AND FIRMLY TIGHTENED. Slide canopy up to the ceiling as shown in Figure 14. Make sure you place the wires safely into the outlet box. Secure the canopy to the hanger bracket with the four screws with your fan. Raise up canopy ring and line up the 4 tabs with the 4 grooves on the canopy.
Attaching the Fan Blades Motor CAUTION MOTOR IS SHIPPED WITH RUBBER MOTOR STOPS TO PREVENT MOVEMENT DURING TRANSPORTATION. REMOVE MOTOR STOPS PRIOR TO ATTACHING BLADE BRACKETS. (FIG. 16) Tab Slot 1. Attach blades to blade arms using three screws with fiber washers. (Fig. 17) Start a screw into the blade arm, do not tighten. Repeat for the 2 remaining screws and washers. Rubber Packing Mounts Screws Figure 16 2. Tighten each screw securely starting with the center screw. Make sure the blade is straight.
Blade Balancing The following procedure should correct most fan wobble. Check after each step. Touching Ceiling 1. Check that all blade and blade bracket screws are secure. 2. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades. Measure from a point on the center of each blade to the point on the ceiling. Measure this distance as shown in Figure 19.
Installing the Light kit CAUTION BEFORE STARTING INSTALLATION, DISCONNECT THE POWER BY TURNING OFF THE CIRCUIT BREAKER OR REMOVING THE FUSE AT FUSE BOX. TURNING POWER OFF USING THE FAN SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRIC SHOCK. NOTE LIGHT BULBS HAVE NO WARRANTY; CAN BE PURCHASED AT ANY HOME DEPOT STORE. 1. While holding the light kit under your fan, locate two single white and blue wires in the switch housing labeled "FOR LIGHT".
Operating Your Fan WARNING LOCKING SLOTS OF CEILING CANOPY ARE PRVIDED ONLY AS AN AID TO MOUNTING. DO NOT LEAVE FAN ASSEMBLY UNATTENDED UNTIL ALL FOUR CANOPY SCREWS ARE ENGAGED AND FIRMLY TIGHTENED. Warm weather - (Counter Clockwise Direction) A downward air flow creates a cooling effect as shown in Figure 22. This allows you to set your air conditioner on a higher setting without affecting your comfort. NOTE WAIT FOR FAN TO STOP BEFORE REVERSING THE DIRECTION OF THE BLADE ROTATION.
Care of Your Fan Troubleshooting Here are some suggestions to help you maintain your fan. PROBLEM SOLUTION Fan will not start 1. Check main and branch circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. Fan sounds noisy 1. Make sure all motor housing screws are snug. 2. Make sure the screws that attach the fan blade bracket to the motor hub is tight. 3.
Specifications FAN SIZE SPEED VOLTS AMPS LOW 52” MED. HIGH 120 WATTS RPM CFM 0.21 12 65 1800 0.38 35 115 3700 0.51 63 160 5450 These are approximate measures. They do not include Amps and Wattage used by the light kit . 14 N.W. G.W. C.F. 8.5 kgs (18.7 Ibs) 9.2 kgs (20.2 Ibs) 1.
Lifetime Limited Warranty (lifetime warranty on motor) The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser.
