705 S/O 707 635 S/O 635 998 S/O 560 Largo 48 Largo 1 22 544 608 289 412 418 459
48” Largo Ceiling Fan by Hampton Bay Accu-Arm™ for Accurate and Easy Installation Indoor/Outdoor Use 3-Speed Reverse Function for Year-Round Comfort and Savings Tri-Mount Installation Thank you for purchasing this Hampton Bay ceiling fan. This product has been manufactured with the highest standards of safety and quality. The finish of this fan is weather resistant, but over time will naturally weather and fade. Table of Contents Safety Rules................................... 1 Unpacking Your Fan.......
READ AND SAVE THESE INSTRUCTIONS 1. To reduce the risk of electric shock, insure electricity 2. 3. 4. 5. has been turned off at the circuit breaker or fuse box before beginning. All wiring must be in accordance with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
1 7 4 2 a b c d 5 3 6 8 Unpack your fan and check the contents. You should have the following items: 1. 2. 3. 4. 5. 6. Slide-On Mounting Plate (inside canopy) Ball/Downrod Assembly Canopy with Canopy Ring attached Fan Motor Assembly Switch Cup Decorative Motor Collar Cover 7. Blades (5) 8. Blade Bracket (Flange) Set (5) with blade bracket screws pre-installed IMPORTANT: THIS PRODUCT AND/OR COMPONENTS ARE COVERED BY ONE OR MORE OF THE FOLLOWING U.S.
Tools Required Phillips screw driver, straight slot screw driver, adjustable wrench, step ladder, and wire cutters. Figures 1, 2, and 3 are examples of different ways to mount the outlet box. Provide Strong Support Ceiling Mounting Plate Recessed Outlet Box Mounting Options Figure 3 If there isn’t an existing outlet box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Outlet Box Secure the outlet box directly to the building structure.
Hanging the Fan REMEMBER to turn off the power. Follow the steps below to hang your fan properly. NOTE: This ceiling fan is supplied with two types of hanging assemblies; the standard ceiling installation using the downrod with ball and socket mounting, and the “close-toceiling” mounting. The “close-to-ceiling” mounting is recommended in rooms with less than 8-foot ceilings or in areas where additional space is desired from the floor to the fan blades.
4. Loosen, but do not remove, the set “Close-to-Ceiling” Mounting screw on the collar on the top of the 1. Remove the canopy ring from the canopy motor housing. by turning the ring to the right until it 5. Align the holes at the bottom of the unlocks (Figure 5). downrod with the holes in the collar 2. Remove the mounting plate from the canoon top of the motor housing (Figure 7). py by loosening the four screws on the top Carefully insert the hanger pin through of the canopy.
WHEN USING THE STANDARD BALL/DOWNROD MOUNTING, THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING BRACKET MUST REST IN THE GROOVE OF THE HANGER BALL. FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING. Installing Fan to the Outlet Box hook provided by utilizing one of the holes at the outer rim of the ceiling canopy (Figure 12). If using standard mounting, seat the hanger ball in the mounting plate socket.
EACH WIRE NUT (WIRE CONNECTOR) SUPPLIED WITH THIS FAN IS DESIGNED TO ACCEPT UP TO ONE 12 GAUGE HOUSE WIRE AND TWO WIRES FROM THE FAN. IF YOU HAVE LARGER THAN 12 GAUGE HOUSE WIRING OR MORE THAN ONE HOUSE WIRE TO CONNECT TO THE FAN WIRING, CONSULT AN ELECTRICIAN FOR THE PROPER SIZE WIRE NUTS TO USE.
CLOSE-TO-CEILING MOUNTING 1. Carefully unhook the fan from the mounting bracket and align the locking slots of the ceiling canopy with the two screws in the mounting plate. Push up to engage the slots and turn clockwise to lock in place. Immediately tighten the two mounting screws firmly. LOCKING SLOTS OF CEILING CANOPY ARE PROVIDED ONLY AS AN AID TO MOUNTING. DO NOT LEAVE FAN ASSEMBLY UNATTENDED UNTIL ALL FOUR CANOPY SCREWS ARE ENGAGED AND FIRMLY TIGHTENED. 2.
Blade Balancing All blades are grouped by weight. Because natural woods vary in density, the fan may wobble even though the blades are weight matched. The following procedure should correct most fan wobble. Check after each step. 1. Check that all blade and blade bracket screws are secure. 2. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades.
Care of Your Fan Here are some suggestions to help you maintain your fan. 1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) 2. Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, this could damage the motor, or the wood or possibly cause an electrical shock.
FAN SIZE SPEED VOLTS 48” AMPS WATTS RPM CFM Low 120 0.25 13.2 77 2257 Med 120 0.38 30.6 126 3466 High 120 0.55 66.6 187 5034 NET WEIGHT GROSS WEIGHT CUBE FEET 21.3 Lbs 23.5 Lbs 1.43’ These are approximate measures. They do not include Amps and Wattage used by the light kit. Distributed by Your Other Warehouse LLC 12100 Little Cayman Dr. Baton Rouge, LA 70809 Vendor number: 219030 Specifications 11.
Hampton Bay Lifetime Limited Warranty Lifetime Warranty on Motor Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a lifetime after the date of purchase by the original purchaser.
Largo de 48" Ventilador de techo de Hampton Bay Accu-arm™ para una instalación fácil y precisa Para uso en interiores y exteriores Gracias por comprar este ventilador de techo de Hampton Bay. Este producto se ha fabricado con las normas de seguridad y calidad más altas. El acabado de este ventilador es resistente a la intemperie, pero con el tiempo, exhibirá un desgaste y decoloración naturales. Índice Normas de seguridad.................... 1 Cómo desempacar el ventilador..
LEE LAS INSTRUCCIONES Y GUÁRDALAS 1. Para disminuir el riesgo de descarga eléctrica, asegúrate de 2. 3. 4. 5. 6. que la electricidad ha sido apagada en el cortacircuitos o la caja de fusibles antes de comenzar la instalación. Todo el cableado debe cumplir con el Código Nacional de Electricidad ANSI/NFPA 70-1999 y con los códigos locales de electricidad. La instalación eléctrica debe ser hecha por un electricista certificado y calificado.
1 7 4 2 a b c d 5 3 6 8 Desempaca tu ventilador y revisa el contenido. Deberá tener las siguientes piezas: 1. Placa de montaje deslizante (dentro de la cubierta) 2. Ensamblado de tubo bajante/bola 3. Cubierta con anillo de cubierta acoplado 4. Ensamblado del motor del ventilador 5. Caja del interruptor 6. Cubierta decorativa del collarín del motor 7. Aspas (5) 8.
Herramientas necesarias Las figuras 1, 2 y 3 son ejemplos de diferentes formas de montar la caja eléctrica. Soporte fuerte Destornillador Phillips, destornillador plano, llave ajustable, escalera de tijera y cortacables. Placa de montaje en el techo Caja eléctrica empotrada Figura 3 Opciones de montaje Caja eléctrica Si no hay una caja eléctrica existente, entonces lee las siguientes instrucciones. Desconecta la energía retirando los fusibles o apagando los cortacircuitos.
Cómo colgar el ventilador RECUERDA desconectar la corriente. Sigue estos pasos para colgar correctamente tu ventilador. NOTA: Este ventilador de techo viene con dos tipos de ensamblados de soporte; la instalación de techo estándar con tubo bajante y bola, y casquillo de montaje; y el montaje “cerca del techo”. El montaje “cerca del techo” se recomienda en habitaciones con techos de menos de 8 pies de altura o en áreas donde se desee espacio adicional desde el piso hasta las aspas de ventilador.
4. Afloja, sin quitarlo, el tornillo en el collarín ubicado en la parte superior de la carcasa del motor. 5. Alinea los orificios en la parte inferior del tubo bajante con los orificios en el collarín ubicado en la parte superior de la carcasa de motor (Figura 7). Inserta con cuidado el pasador de soporte a través de los orificios del collarín y del tubo bajante. Ten cuidado de no apretarlo contra el cableado dentro del tubo bajante.
CUANDO USES EL MONTAJE DE TUBO BAJANTE Y BOLA ESTÁNDAR, LA PESTAÑA EN EL ARO EN LA PARTE INFERIOR DEL SOPORTE DE MONTAJE DEBE ENCAJAR EN LA RANURA DE LA BOLA DE SOPORTE. SI NO ENCAJA CORRECTAMENTE, SE PUEDE DAÑAR EL CABLEADO. Cómo instalar el ventilador en la caja eléctrica CUANDO MONTES EL VENTILADOR EN UN TECHO INCLINADO, DEBES USAR EL MÉTODO DE MONTAJE CON TUBO BAJANTE Y BOLA ESTÁNDAR.
Interruptor MONTAJE DE TECHO ESTÁNDAR Caja eléctrica AZUL NEGRO BLANCO VERDE PARA REDUCIR EL RIESGO DE INCENDIO O DESCARGA ELÉCTRICA, NO UTILICES ESTE VENTILADOR CON NINGÚN DISPOSITIVO DE CONTROL DE VELOCIDAD DE ESTADO SÓLIDO, DE MONTAJE EN PARED. EL CIRCUITO ELECTRÓNICO SE DAÑARÁ EN FORMA PERMANENTE. Finalizar la instalación del ventilador CIRCUITO DE SUMINISTRO NEGRO BLANCO 5. Gira las tuercas de conexión del cable hacia arriba y coloca el cableado dentro de la caja eléctrica.
MONTAJE CERCA DEL TECHO 1. Con cuidado desengancha el ventilador del soporte de montaje y alinea las ranuras de cierre de la cubierta del techo con los dos tornillos en la placa de montaje. Alza para enganchar las ranuras y gira de izquierda a derecha para asegurar en su sitio. Ajusta con firmeza los dos tornillos de montaje. LAS RANURAS DE CIERRE DE LA CUBIERTA DEL TECHO SÓLO SIRVEN DE AYUDA DURANTE LA INSTALACIÓN.
Equilibrar las aspas Todas las aspas se agrupan por peso. Como las maderas naturales varían en densidad, el ventilador puede oscilar aunque las aspas tengan el mismo peso. El siguiente procedimiento corregirá en gran medida la oscilación del ventilador. Verifica después de cada paso. 1. Verifica que todas las aspas y tornillos de los soportes de aspas estén seguros. 2. La mayoría de los problemas de oscilación del ventilador se deben a que las aspas no están a un mismo nivel.
Cuidado del ventilador Solución de problemas Aquí tienes algunas sugerencias para el mantenimiento de tu ventilador. 1. Debido al movimiento natural del ventilador, algunas conexiones pueden aflojarse. Revisa las conexiones de soporte, soportes y accesorios de aspas dos veces al año. Verifica que estén seguros. (No es necesario desmontar el ventilador del techo). 2. Limpia tu ventilador con frecuencia, para que luzca como nuevo a pesar de los años.
TAMAÑO 48” VELOCIDAD VOLTIOS AMPERIOS VATIOS RPM PIES CÚB. X MIN. Baja 120 0.25 13.2 77 2257 Media 120 0.38 30.6 126 3466 Alta 120 0.55 66.6 187 5034 Estas medidas son aproximadas. No incluyen ni el amperaje ni el vataje consumido por el kit de luces. Distribuido por Your Other Warehouse LLC 12100 Little Cayman Dr. Baton Rouge, LA 70809 Número del proveedor: 219030 11. Especificaciones PESO NETO PESO BRUTO PIES CÚB. 21.3 Lb 23.5 Lb 1.
Garantía limitada de por vida de Hampton Bay Garantía de por vida para el motor NOTA IMPORTANTE: Para asegurar la garantía de servicio, si es necesario, registre su ventilador en: gpwarranty.com Hampton Bay garantiza de por vida, a partir de la fecha de compra por el comprador original, que el motor del ventilador no presenta defectos de fabricación ni de material desde la fecha de salida de la Usted debe presentar una copia del fábrica.