Use and Care Manual

ManualsBrandsHampton Bay ManualsDeck LightingSolar 4 in. x 4 in. Bronze Outdoor Integrated LED Deck Post Light with 6 in. x 6 in. Adapter (2-Pack)

HAMPTONBAY.COM

Please contact 1-855-HD-HAMPTON for further assistance

SOLAR POST CAP

ITEM # 1000000000

MODEL # 47577

Use and Care

Guide

TOOLS REQUIRED

HARDWARE INCLUDED

Phillips

screwdriver

AA - Mounting Wood

Screw x 2

Installation

□ To mount the solar post cap to a 4x4 square wood post, place the mounting collar (D) over the top of the 4x4 square wood post,

and secure it by screwing the two mounting screws (AA) into the wood post.

□ To mount the solar post cap to a 6x6 square wood post, align and snap the 6x6 adaptor (E) into the mounting collar (D). Place the

assembled 6x6 adaptor (E) over the top of the 6x6 square wood post, and secure it by screwing the two mounting screws (AA)

into the wood post.

□ Prior to use, rotate counterclockwise and remove the top cap (A) from the lamp housing (B). Then, remove the battery isolator tag

(C) inserted in the battery compartment. Replace the top cap back to the lamp housing and allow it to charge a full sunny day.

IMPORTANT: Ensure the mounting location for your solar light

allows the solar panel to receive direct sunlight. Do not locate

the product in shaded areas as this will significantly reduce

performance.

NOTE: The solar light is equipped with a photosensor that

turns the unit on at dusk and off at dawn. Ambient light can

affect the operation of the photosensor.

Safety Information

WARNING: Your solar light may not function in temperatures

below -4ºF (-20ºC) or above 140ºF (60ºC).

CAUTION: Use a rechargeable battery only. Recycle or

dispose of batteries properly.

CAUTION: Do not open, short circuit, or mutilate batteries as

injury may occur.

Summary of content (4 pages)

PAGE 1
SOLAR POST CAP Use and Care Guide ITEM # 1000000000 MODEL # 47577 TOOLS REQUIRED HARDWARE INCLUDED Phillips screwdriver AA - Mounting Wood Screw x 2 Installation □ □ □ To mount the solar post cap to a 4x4 square wood post, place the mounting collar (D) over the top of the 4x4 square wood post, and secure it by screwing the two mounting screws (AA) into the wood post. To mount the solar post cap to a 6x6 square wood post, align and snap the 6x6 adaptor (E) into the mounting collar (D).
PAGE 2
Maintenance Replacing the battery IMPORTANT: Dispose of the battery in accordance with local, state, and federal regulations. IMPORTANT: When storing any solar product for an extended period of time, remove the batteries. Storing any solar product without regular recharge or removal of batteries could cause permanent damage to the rechargeable batteries. NOTE: Use one AA size, 700mAh, 1.2V Nickel Metal Hydride rechargeable battery.
PAGE 3
TAPA DE POSTE SOLAR ARTÍCULO N.º100000000 MODELO N.º47577 Guía de uso y cuidado HERRAMIENTAS REQUERIDAS HERRAJE INCLUIDO Destornillador Phillips AA - 2 tornillos de madera para montaje Instalación □ □ □ Para montar la tapa del poste solar a un poste de madera cuadrado de 4x4, coloque el cuello de montaje (D) sobre la parte superior del poste de madera cuadrado de 4x4, y sujételo atornillando los dos tornillos de montaje (AA) en el poste de madera.
PAGE 4
Mantenimiento Cómo reemplazar la pila IMPORTANTE: Deseche la pila cumpliendo con los reglamentos locales, estatales y federales. IMPORTANTE: Al almacenar cualquier producto solar durante un periodo prolongado de tiempo, retire las pilas. Almacenar cualquier producto solar sin la recarga habitual o extracción de pilas podría causar daño permanente a las pilas recargables. NOTA: Use una pila recargable de tamaño AA, 700 mAh, 1.2 V de níquel-metal hidruro.