672 S/O 672 672 S/O 672 Algiers 54 Algiers 37 099 396 132 429
54” Algiers Ceiling Fan by Hampton Bay 3-Speed Reverse Function for Year-Round Comfort and Savings Thank you for purchasing this Hampton Bay ceiling fan. This product has been manufactured with the highest standards of safety and quality. The finish of this fan is weather resistant, but over time will naturally weather and fade. Table of Contents Safety Rules................................... 1 Tri-Mount Installation Unpacking Your Fan.....................
READ AND SAVE THESE INSTRUCTIONS 1. To reduce the risk of electric shock, insure electricity 2. 3. 4. 5. has been turned off at the circuit breaker or fuse box before beginning. All wiring must be in accordance with the National Electrical Code (ANSI/NFPA 70-1999) and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state fan speed control device.
Unpack your fan and check the contents. You should have the following items: 1. 2. 3. 4. 5. 6. Mounting Plate (Inside Canopy) Ball/Downrod Assembly Canopy Decorative Motor Collar Cover Fan Motor Assembly Switch Cup Cover 7. Blade Bracket 8. Blades (5) 9. Light Kit Fitter 10. Glass Bowl 11. Bulb (2) IMPORTANT: THIS PRODUCT AND/OR COMPONENTS ARE COVERED BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS: 5,947,436; 5,988,580; 5,971,573; 6,010,306; 6,039,541; 6,046,416 AND OTHER PATENTS PENDING. 2.
Tools Required Phillips screw driver, straight slot screw driver, adjustable wrench, step ladder, and wire cutters. Figures 1, 2, and 3 are examples of different ways to mount the outlet box. Mounting Options Figure 3 Outlet Box If there isn’t an existing outlet box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials.
Hanging the Fan REMEMBER to turn off the power. Follow the steps below to hang your fan properly. NOTE: This ceiling fan is supplied with two types of hanging assemblies; the standard ceiling installation using the downrod with ball and socket mounting, and the “close-toceiling” mounting. The “close-to-ceiling” mounting is recommended in rooms with less than 8-foot ceilings or in areas where additional space is desired from the floor to the fan blades.
2. Remove the mounting plate from the canopy by loosening the four screws on the top of the canopy. Remove the two non-slotted screws and loosen the slotted screws. This will enable you to remove the mounting plate (Figure 6). 6. Align the mounting holes with the holes in the motor and fasten, using the three screws and lockwashers removed in step 4 (Figure 10). 7. Tighten the mounting screws securely.
Installing Fan to the Outlet Box WHEN MOUNTING THE FAN ON A SLOPED CEILING, THE STANDARD BALL/DOWNROD MOUNTING METHOD MUST BE USED. MAKE SURE THE MOUNTING PLATE SLOTS ARE ON THE LOWER SIDE BY SLIDING THE MOUNTING PLATE FROM THE TOP DOWN. 1. Pass the 120-volt supply wires through the center hole in the ceiling mounting plate as shown in Figure 7. 2. Install the ceiling mounting plate on the outlet box by sliding the mounting plate over the two screws provided with the outlet box (Figure 7).
Making the Electrical Connections 5. Turn the wire connecting nuts upward and push the wiring into the outlet box. REMEMBER to disconnect the power. If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan. Secure the connectors with electrical tape. Make sure there are no loose strands or connections.
Finishing the Fan Installation STANDARD CEILING MOUNTING WHEN USING THE STANDARD BALL/DOWNROD MOUNTING, THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING PLATE MUST REST IN THE GROOVE OF THE HANGER BALL. FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING. 1. Align the locking slots of the ceiling canopy with the two screws in the mounting plate. Push up to engage the slots and turn clockwise to lock in place. Immediately tighten the two mounting screws firmly. 2.
Blade Balancing 4. Remove four mounting screws on the switch cup cover. All blades are grouped by weight. Because natural woods vary in density, the fan may wobble even though the blades are weight matched. 5. Connect the wires exiting the bottom of switch cup cover with the switch cup by connecting the molded adaptor plugs together (Figure 17). The following procedure should correct most fan wobble. Check after each step. 1. Check that all blade and blade bracket screws are secure. 2.
Turn on the power and check the operation of the fan. The pull chain controls the fan speeds as follows: 1 pull - High, 2 pulls Medium, 3 pulls - Low and 4 pulls - Off. Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans, and so on. Figure 16 The reversing switch installed in the switch cup (Figure 17) controls direction: forward (switch left) or reverse (switch right).
Care of Your Fan Troubleshooting 1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) Fan will not start Here are some suggestions to help you maintain your fan. 2. Clean your fan periodically to help maintain its new appearance over the years.
FAN SIZE 54” SPEED VOLTS AMPS WATTS RPM CFM Low 120 0.25 15 65 2289 Med 120 0.38 34 100 3516 High 120 0.52 63 140 5024 These are approximate measures. They do not include Amps and Wattage used by the light kit. Distributed by Your Other Warehouse LLC 12100 Little Cayman Dr. Baton Rouge, LA 70809 Vendor number: 219030 12. Specifications NET WEIGHT GROSS WEIGHT CUBE FEET 27.9 Lbs 31.0 Lbs 2.
Hampton Bay Lifetime Limited Warranty Lifetime Warranty on Motor Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a lifetime after the date of purchase by the original purchaser.
Algiers de 54” Ventilador de techo de Hampton Bay Función de reversa de 3 velocidades para confort y ahorro durante todo el año Gracias por comprar este ventilador de techo de Hampton Bay. Este producto se ha fabricado con las normas de seguridad y calidad más altas. El acabado de este ventilador es resistente a la intemperie, pero con el tiempo, exhibirá un desgaste y decoloración naturales. Índice Normas de seguridad.................... 1 Instalación de montaje triple Cómo desempacar el ventilador...
LEE LAS INSTRUCCIONES Y GUÁRDALAS 1. Para disminuir el riesgo de descarga eléctrica, asegúrate de 2. 3. 4. 5. que la electricidad ha sido apagada en el cortacircuitos o la caja de fusibles antes de comenzar la instalación. Todo el cableado debe cumplir con el Código Nacional de Electricidad (ANSI/NFPA 70-1999) y con los códigos locales de electricidad. La instalación eléctrica debe ser hecha por un electricista certificado y calificado.
Desempaca tu ventilador y revisa el contenido. Deberá tener las siguientes piezas: 1. 2. 3. 4. 5. 6. Placa de montaje (dentro de la cubierta) Ensamblado de tubo bajante/bola Cubierta Cubierta decorativa del collarín del motor Ensamblado del motor del ventilador Cubierta de la caja del interruptor 7. Soporte de aspa 8. Aspas (5) 9. Soporte del kit de luces 10. Tazón de vidrio 11. Bombillas (2) IMPORTANTE: ESTE PRODUCTO Y/O SUS COMPONENTES ESTÁN PROTEGIDOS POR UNAO MÁS DE LAS SIGUIENTES PATENTES DE EE.UU.
Herramientas necesarias Destornillador Phillips, destornillador plano, llave ajustable, escalera de tijera y cortacables. Las figuras 1, 2 y 3 son ejemplos de diferentes formas de montar la caja eléctrica. Placa de montaje en el techo Caja eléctrica empotrada Opciones de montaje Figura 3 Si no hay una caja eléctrica existente, entonces lee las siguientes instrucciones. Desconecta la energía retirando los fusibles o apagando los cortacircuitos.
Cómo colgar el ventilador RECUERDA desconectar la corriente. Sigue estos pasos para colgar correctamente tu ventilador. NOTA: Este ventilador de techo viene con dos tipos de ensamblados de soporte; la instalación de techo estándar con tubo bajante y bola, y casquillo de montaje; y el montaje “cerca del techo”. El montaje “cerca del techo” se recomienda en habitaciones con techos de menos de 8 pies de altura o en áreas donde se desee espacio adicional desde el piso hasta las aspas de ventilador.
Tornillos de montaje (incluidos con la caja eléctrica) Caja eléctrica aprobada por UL Deslizar la placa de montaje sobre las cabezas de los tornillos Cables de 120 voltios Gancho 3. Retira la cubierta decorativa de la tapa inferior de la cubierta oprimiendo los tres pernos (Figura 8). 4.
Cómo instalar el ventilador en la caja eléctrica CUANDO MONTES EL VENTILADOR EN UN TECHO INCLINADO, DEBES USAR EL MÉTODO DE MONTAJE CON TUBO BAJANTE Y BOLA ESTÁNDAR. ASEGÚRATE DE QUE LAS RANURAS DE LA PLACA DE MONTAJE ESTÉN EN EL LATERAL INFERIOR MEDIANTE EL DESLIZAMIENTO DE LA PLACA DE MONTAJE DESDE ARRIBA HACIA ABAJO. 1. Pasa los cables de suministro de 120 voltios a través del orificio central de la placa de montaje del techo como se muestra en la Figura 7. 2.
Sigue estos pasos para conectar tu ventilador a tu circuito doméstico. Usa las tuercas de conexión de cables que vienen con tu ventilador. Asegura los conectores con cinta aislante.Asegúrate de que no existan conexiones o cables sueltos. 1. Conecta los dos cables verdes de conexión a tierra del ventilador, ubicados en el tubo bajante y la placa de montaje, al cable de conexión a tierra de la casa.
Finalizar la instalación del ventilador MONTAJE DE TECHO ESTÁNDAR CUANDO USES EL MONTAJE DE TUBO BAJANTE Y BOLA ESTÁNDAR, LA PESTAÑA EN EL ARO EN LA PARTE INFERIOR DE LA PLACA DE MONTAJE DEBE ENCAJAR EN LA RANURA DE LA BOLA DE SOPORTE. SI NO ENCAJA CORRECTAMENTE, SE PUEDE DAÑAR EL CABLEADO. 1. Alinea las ranuras de cierre de la cubierta de techo con los dos tornillos de la placa de montaje. Alza para enganchar las ranuras y gira de izquierda a derecha para asegurar en su sitio.
Equilibrar las aspas Todas las aspas se agrupan por peso. Como las maderas naturales varían en densidad, el ventilador puede oscilar aunque las aspas tengan el mismo peso. 3. Reinstala el tornillo de montaje que retiraste en el paso 1 y apriétalo firmemente (Figura 16). Punto en el techo 4. Quita los cuatro tornillos de montaje en la cubierta de la caja del interruptor. 5.
Enciende la electricidad y verifica el funcionamiento del ventilador. El interruptor de cadena controla las velocidades del ventilador de la siguiente manera: 1 vez: Alto, 2 veces: Medio, 3: Bajo y 4: Apagado. Tornillos del soporte negro Cubierta de la caja del interruptor Tornillos Las configuraciones de velocidad para clima cálido o frío dependen de factores como tamaño de la habitación, altura del techo, cantidad de ventiladores y demás.
Cuidado del ventilador Solución de problemas Aquí tienes algunas sugerencias para el mantenimiento de tu ventilador. Problema Solución 1. Debido al movimiento natural del ventilador, algunas conexiones pueden aflojarse. Revisa las conexiones de soporte, soportes y accesorios de aspas dos veces al año. Verifica que estén seguros. (No es necesario desmontar el ventilador del techo). El ventilador no enciende 2. Limpia tu ventilador con frecuencia, para que luzca como nuevo a pesar de los años.
TAMAÑO 54” VELOCIDAD VOLTIOS AMPERIOS VATIOS RPM PIES CÚB. X MIN. Baja 120 0.25 15 65 2289 Media 120 0.38 34 100 3516 Alta 120 0.52 63 140 5024 PESO NETO PESO BRUTO PIES CÚB. 27.9 Lb 31.0 Lb 2.28 Estas medidas son aproximadas. No incluyen ni el amperaje ni el vataje consumido por el kit de luces. Distribuido por Your Other Warehouse LLC 12100 Little Cayman Dr. Baton Rouge, LA 70809 Número del proveedor: 219030 Especificaciones 12.
Garantía limitada de por vida de Hampton Bay Garantía de por vida para el motor Hampton Bay garantiza de por vida, a partir de la fecha de compra por el comprador original, que el motor del ventilador no presenta defectos de fabricación ni de material desde la fecha de salida de la fábrica.