Model # 5RGZ1389-WBS USE AND CARE GUIDE 9 FT X 9 FT PERGOLA Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8.00 a.m. - 7.00 p.m. EST, Monday - Friday, 9.00 a.m. - 6.00 p.m. EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM THANK YOU pergola. to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.
Table of Contents Table of Contents ........................................................2 Safety Information .......................................................2 Care Instructions ....................................................................2 Pre-Assembly ............................................................3 Planning Assembly...................................................................3 Part List...................................................................................
Pre-Assembly PLANNING ASSEMBLY It will take at least three people about 30 minutes to complete the assembly process. A Philips screwdriver, a rubber mallet and a free standing ladder are needed during the assembly process.
Pre-Assembly NOTE: Hardware not shown to actual size. AA BB Part Description CC AA BB Bolt (M6x20) Bolt (M6x35) Bolt (M6x70) Washer(Ф8.8x1.0) Bolt cap (Ф16x5) Hex wrench Ground stake (Ф4x137) CC DD FF DD EE FF GG EE GG Quantity 117 19 3 139 139 1 8 Assembly 1 Attaching post bases AA DD EE 8 DD AA EE A x2 8 Bx2 8 M FF Attach one post base (M) to the bottom of each corner post (A)/(B) with washers (DD) and bolts (AA) using hex wrench (FF).
Assembly 2 Attaching cross beam (D) AA 8 DD 8 D EE AA DD 8 EE B D FF B B Attach the top of one corner post (B) to each end of cross beam (D) with washers (DD) and bolts (AA) using hex wrench (FF). 3 Attaching cross bar (F) AA 4 DD 4 EE 4 DD AA EE B B FF F Attach cross bar (F) to the lower portion of both corner posts (B) with washers (DD) and bolts (AA) using hex wrench (EE). 5 HAMPTONBAY.COM Please contact 1-855-HD-HAMPTON for further assistance.
Assembly 4 Installing slat panels AA 69 DD 69 EE 69 I H FF H Attach slat (I) onto the three supports tubes (H) with washers (DD) and bolts (AA) using hex wrench (FF). EE AA DD H Do not fully tighten bolts until the end of step .5 5 BB CC EE Attaching the slat panel CC DD F 3 DD BB EE 3 D DD 6 EE 6 FF Inset the slat panel from step 4 into the frame from step 3. Secure support bars (H) onto the cross beam (D) with washers (DD) and bolts (CC) using hex wrench (FF).
Assembly 6 Erecting the frame D EE AA DD E E C B EE B Insert E AA DD AA A Ga C p A Place the corner posts (B) upright. With a ladder attach roof rails (E) to corner posts (B) at the top with washers (DD) and bolts (AA) using hex wrench (FF). Insert the top of corner post (A) into cross beam (C). Place the corner posts (A) upright. Attach the top of corner posts (A) to the other side of roof rails (E) with washers (DD) and bolts (AA) using hex wrench (FF).
Assembly 7 Attaching roof rail (G) AA 4 DD 4 EE 4 D G C FF D DD AA EE G Attach the roof rail (G) to cross beam (C) and (D) with washers (DD) and bolts (AA) using hex wrench (FF).
Assembly 8 Assembling roof panels N J K J K DD BB EE BB 16 DD 16 EE 16 L FF Insert roof panel tubes (K) into sling (N) in the direction of depth. Insert roof panel tubes (J) into sling (N) in the direction of width. Secure tubes (J) and tubes (K) at four corners with washers (DD) and bolts (BB) using hex wrench (FF). Plug roof panel tube (L) into roof tubes (K) in the center. Repeat the above procedure for the other three sling panels. 9 HAMPTONBAY.
9 Assembly Installing roof panels Slide two roof panels into the upper roof rails . Slide the other roof panels into the lower roof rails.
Assembly 10 Fixing the Cross Beam (C) and Anchoring the Pergola E AA 8 DD 8 EE AA AA DD Pull out EE 8 C FF GG 8 II 1 Move roof panels II DD AA EE E [L] E C A A GG Remove the temporary bolts from cross beam (C). Minimize the gaps between cross beam (C) and roof rails (E). Secure cross beam (C) and corner posts (A) with washers (DD) and bolts (AA) using hex wrench (FF). When all bolts are firmly secured, cover them with bolt caps (EE). Adjust each corner post upright.
Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8.00 a.m. - 7.00 p.m. EST, Monday - Friday, 9.00 a.m. - 6.00 p.m. EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM Retain this manual for future use.