Instructions / Assembly

4
• The LP gas tank should not be dropped or handled roughly.
• Tanks must be stored outdoors out of the reach of children. Do NOT store in a building, garage, or any other enclosed
area.
• Never store your LP gas tank where temperatures can reach over 125°F.
• Never keep a filled LP gas tank in a hot car or car trunk. Heat will cause the gas pressure to increase, which may open the relief
valve and allow gas to
escape.
• Place dust cap on valve outlet whenever the LP gas tank is not in use. Only install the type of dust cap on the LP gas tank valve
outlet that is provided with the LP gas tank valve. Other types of caps or plugs may result in leakage of propane.
• Do not store a spare LP gas tank under or near this gas appliance.
• Never fill the tank beyond 80 percent full.
• LP gas cylinders should only be filled by a certified LP gas dealer.
• The pressure regulator is set for 11 inches of water column (pressure).
• The maximum inlet gas pressure for this outdoor appliance is 14 inches of water column pressure.
• Any guard or other protective device removed for servicing the appliance must be replaced prior to operating the appliance.
• Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least
annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative that
control
compartment, burners and circulating air passageways of the appliance be kept clean.
• The appliance should be inspected before use and at least annually by a qualified service person.
• Do not attempt to disconnect the gas regulator from the tank or any gas fitting while the outdoor appliance is in use.
• Keep gas appliance away from location where it can get excessively wet. Do not use gas appliance if any part has been
underwater. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control
system
and any gas control which has been under water.
• This appliance shall be used only outdoors in a well-ventilated space and shall not be used in a building, garage or any other
enclosed area.
• The LP-gas supply cylinder must be disconnected when this appliance is not in use
• Only cylinder marked “propane” shall be
used.
• Be sure to use only one 20 lb (9.1 kg) LP gas cylinder with a Type 1 valve with this appliance as required by the
American
National Standards Institute (ANSI) and the Canadian Standards Steering Committee.
• LP gas cylinder must contain a shut-off valve as specified in the Standard for Compressed Gas Cylinder Valve Outlet and Inlet
Connection,
ANSI/CGA-V-1-1977, CSA B96.
• Never attempt to attach this appliance to the self-contained LP gas system of a camper trailer, motor home or house.
• Hand turn the manual gas control valve. Never use tools. If the valve will not turn by hand, do not try to repair it. Call a
Certified
Gas Technician. The use of force or any self attempted repair may result in a fire or explosion.
• WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to
the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified
installer, service agency or the gas supplier.
LP Hose and Regulator Assembly and Replacement
1 This appliance comes equipped with a standard LP gas hose and regulator including the appliance side connection for a CGA
No
791 Cylinder Connection Device. The LP gas hose and regulator supplied with this appliance must be used. Only a hose
and
regulator specified by manufacturer can be used for replacement.
a) The CGA No 791 connection incorporates an excess flow limiting device that acts to limit the flow of gas if a leak is detected
between the regulator and the burner valve.
b) If the burner valve is open prior to the LP gas cylinder service valve being opened, the connection will interpret this free flow of
gas to be a leak
c) The connection safety feature will reduce gas flow from the regulator to the appliance to a minimal level.
d) Be sure that the burner control valve is closed prior to opening the LP gas cylinder service valve to ensure that the connection
flow limiting device is not triggered
mistakenly.
e) If the connection flow limiting device is triggered mistakenly, close the LP gas cylinder service valve and the burner valve, wait
10 seconds to allow the device to reset, open the cylinder service valve, then open the burner.
valve and light the appliance as per lighting instructions.
2 Be sure to protect the hose from any hot surfaces. Serious danger may result if the hose contacts any hot surface.
3 Regular maintenance of the hose and
regulator: