666 834 San Marino 36 in Ceiling Fan Owner’s Manual San Marino Ventilador de Techo de 0,91 m Manual del Propietario
36” San Marino Ceiling Fan by Hampton Bay 3-Speed Reverse Function for Year-Round Comfort and Savings Steeper Blade Pitch for Greater Air Movement Tri-Mount Installation Accu-Arm™ for Accurate and Easy Installation Thank you for purchasing this Hampton Bay ceiling fan. This product has been manufactured with the highest standards of safety and quality. The finish of this fan is weather resistant, but over time will naturally weather and fade. Table of Contents Safety Rules.................................
READ AND SAVE THESE INSTRUCTIONS 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National Electrical Code and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state fan speed control device. 4.
Unpack your fan and check the contents. You should have the following items: 1. 2. 3. 4. Fan Motor Assembly Canopy Blades (5) Blade Bracket Set (5) with motor screws pre-installed 5. Ball/Downrod Assembly 6. Slide-On Mounting Bracket and Mounting Hardware 7. Light Kit Fitter 8. Shade 9. Decorative Motor Collar Cover 10. CFL Bulb 11. Extra Switch Cap Cover IMPORTANT: THIS PRODUCT AND/OR COMPONENTS ARE COVERED BY ONE OR MORE OF THE FOLLOWING U.S.
Tools Required Phillips screw driver, straight slot screw driver, adjustable wrench, step ladder, and wire cutters. Figures 1, 2, and 3 are examples of different ways to mount the outlet box. Provide Strong Support Ceiling Mounting Plate Recessed Outlet Box Mounting Options Figure 3 Outlet Box If there isn’t an existing mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure.
Hanging the Fan REMEMBER to turn off the power. Follow the steps below to hang your fan properly. NOTE: This ceiling fan is supplied with two types of hanging assemblies; the standard ceiling installation using the downrod with ball and socket mounting, and the “close-toceiling” mounting. The “close-to-ceiling” mounting is recommended in rooms with less than 8-foot ceilings or in areas where additional space is desired from the floor to the fan blades.
“Close-to-Ceiling” Mounting 1. Remove the mounting bracket from the canopy by loosening the four screws on the top of the canopy. Remove the two nonslotted screws and loosen the slotted screws. This will enable you to remove the hanger bracket (Figure 5). 2. Remove the decorative canopy bottom cover from the canopy by depressing the three studs (Figure 7). 4.
Installing Fan to the Outlet Box TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL INJURY, MOUNT FAN ONLY TO AN OUTLET BOX MARKED ACCEPTABLE FOR FAN SUPPORT AND USE THE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX. 1. Pass the 120-volt supply wires through the center hole in the ceiling mounting bracket as shown in Figure 10. 2. Install the ceiling mounting bracket on the outlet box by sliding the mounting bracket over the two screws provided with the outlet box.
REMEMBER to disconnect the power. If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan. Secure the connectors with electrical tape. Make sure there are no loose strands or connections. 1.
Finishing the Fan Installation STANDARD CEILING MOUNTING WHEN USING THE STANDARD BALL/DOWNROD MOUNTING, THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING BRACKET MUST REST IN THE GROOVE OF THE HANGER BALL. FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING. 1. Align the locking slots of the ceiling canopy with the two screws in the mounting bracket. Push up to engage the slots and turn clockwise to lock in place. Immediately tighten the two mounting screws firmly. 2.
Attaching the Light Kit Non-Light Kit Option REMEMBER to disconnect the power. 1. Remove the three mounting screws on the light kit fitter. 2. Connect the wires exiting the bottom of the motor with the light kit by connecting the molded adaptor plugs together. 3. Slide the light kit fitter into the switch cup and secure it using the three screws that were removed in step 1. 4. Insert the shade into the shade holder and turn it clockwise to lock in place. Repeat for the remaining shade. 5.
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE HOLDERS WHILE INSTALLING, BALANCING THE BLADES, OR CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING BLADES. Warm weather - (Forward) A downward air flow creates a cooling effect as shown in Figure 16. This allows you to set your air conditioner on a higher setting without affecting your comfort. WAIT FOR FAN TO STOP BEFORE REVERSING THE DIRECTION OF BLADE ROTATION. Turn on the power and check the operation of the fan.
Care of Your Fan Troubleshooting 1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) Fan will not start 2. Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, this could damage the motor, or the wood or possibly cause an electrical shock.
FAN SIZE 36” SPEED VOLTS AMPS WATTS RPM CFM Low 120 0.21 13 80 1450 Med 120 0.3 26 135 2200 High 120 0.42 49 205 3200 These are approximate measures. They do not include Amps and Wattage used by the light kit. Distributed by Home Depot U.S.A., Inc. 2455 Paces Ferry Rd. N.W. Atlanta, Georgia 30339 Vendor number: 11688 12. Specifications N.W. G.W. C.F. 12.54 Lbs 14.19 Lbs 0.
Hampton Bay Lifetime Limited Warranty Lifetime Warranty on Motor Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a lifetime after the date of purchase by the original purchaser.
San Marino de 36” Ventilador de techo de Hampton Bay Función de reversa de 3 velocidades para confort y ahorro durante todo el año Inclinación de aspa más pronunciada para obtener un mayor flujo de aire Instalación de montaje triple Accu-arm™ para una instalación fácil y precisa Gracias por comprar este ventilador de techo de Hampton Bay. Este producto se ha fabricado con las normas de seguridad y calidad más altas.
LEE LAS INSTRUCCIONES Y GUÁRDALAS 1. Para disminuir el riesgo de descarga eléctrica, asegúrate de que la electricidad ha sido apagada en el cortacircuitos o la caja de fusibles antes de comenzar la instalación. 2. Todo el cableado debe cumplir con el Código Nacional de Electricidad y con los códigos locales de electricidad. La instalación eléctrica debe ser hecha por un electricista certificado y calificado. 3.
Desempacar tu ventilador y revisar el contenido. Deberá tener los siguientes artículos: 1. 2. 3. 4. Ensamblado del motor del ventilador Cubierta Aspas (5) Juego de soportes de aspa (5) con tornillos del motor preatornillados 5. Ensamblado de tubo bajante/bola 6. Soporte de montaje deslizante y herrajes de montaje (dentro de la cubierta) 7. Soporte del kit de luces 8. Pantalla 9. Cubierta decorativa del collarín del motor 10. Bombilla CFL 11.
Herramientas necesarias Las figuras 1, 2 y 3 son ejemplos de diferentes formas de montar la caja de distribución. Destornillador Phillips, destornillador plano, llave ajustable, escalera de tijera y cortacables. Figura 3 Opciones de Montaje Si no hay una caja eléctrica, lee las siguientes instrucciones. Desconecta la energía retirando los fusibles o apagando los cortacircuitos. Asegura la caja de distribución directamente a la estructura del edificio.
Cómo colgar el ventilador RECUERDA desconectar la electricidad. Sigue estos pasos para colgar correctamente tu ventilador.. NOTA: Este ventilador de techo viene con dos tipos de ensamblados de soporte; la instalación de techo estándar con tubo bajante y bola, y casquillo de montaje; y el montaje “cerca del techo”. El montaje “cerca del techo” se recomienda en habitaciones con techos de menos de 8 pies de altura o en áreas donde se desee espacio adicional desde el piso hasta las aspas de ventilador.
Montaje “cerca del techo” 1. Retira el soporte de montaje de la cubierta aflojando los cuatro tornillos en la parte superior de la cubierta. Quita los dos tornillos sin ranura y afloja los tornillos ranurados. Esto te permitirá quitar el soporte de montaje (Figura 5). 2. Retira la cubierta inferior decorativa de la cubierta oprimiendo los tres pernos (Figura 7). 4.
Cómo instalar el ventilador en la caja eléctrica PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELÉCTRICA O LESIONES PERSONALES, MONTA EL VENTILADOR SÓLO SOBRE UNA CAJA ELÉCTRICA MARCADA COMO “APROBADA COMO SOPORTE DE VENTILADOR” Y USA TORNILLOS DE MONTAJE QUE VIENEN CON LA CAJA ELÉCTRICA. 1. Pasa los cables de 120 voltios a través del orificio central en el soporte de montaje de techo como lo muestra la figura 10. 2.
Sigue estos pasos para conectar tu ventilador a tu circuito doméstico. Usa las tuercas de conexión de cables que vienen con tu ventilador. Asegura los conectores con cinta aislante. Asegúrate de que no existan conexiones o cables sueltos. 1. Conecta el conductor a tierra del cable de 120 voltios (puede ser un cable desnudo o un cable con aislante verde) al (los) cable(s) terminal(es) a tierra verde (s) del ventilador (Figura 12).
Fin de la instalación del ventilador MONTAJE DE TECHO ESTÁNDAR CUANDO USES EL MONTAJE DE TUBO BAJANTE Y BOLA ESTÁNDAR, LA PESTAÑA EN EL ARO EN LA PARTE INFERIOR DEL SOPORTE DE MONTAJE DEBE ENCAJAR EN LA RANURA DE LA BOLA DE SOPORTE. SI NO ENCAJA CORRECTAMENTE SE PUEDE DAÑAR EL CABLEADO. 1. Alinea las ranuras de cierre de la cubierta de techo con los dos tornillos de la placa de montaje. Alza para enganchar las ranuras y gira de izquierda a derecha para asegurar en su sitio.
Cómo instalar el kit de luces RECUERDA desconectar la electricidad. 1. Quita los tres tornillos de montaje en el soporte negro debajo del motor. 2. Conecta los cables que salen del fondo del motor con el kit de luces, al unir los enchufes con adaptadores moldeados. 3. Desliza el kit de luces con caja de interruptor y asegúralo al soporte negro usando los tres tornillos que se quitaron en el paso 1. 4. Levanta la pantalla en el soporte de pantalla y gira de izquierda a derecha para fijarla en su sitio.
PARA REDUCIR EL RIESGO DE LESIONES PERSONALES, NO DOBLAR LOS SOPORTES DE LAS ASPAS DURANTE LA INSTALACIÓN, COMPENSACIÓN DE LAS ASPAS O LIMPIEZA DEL VENTILADOR. NO INSERTES OBJETOS EXTRAÑOS ENTRE LAS ASPAS EN FUNCIONAMIENTO. Clima cálido - (Hacia adelante) Un flujo de aire hacia abajo crea un efecto refrescante como se muestra en la figura 16. Esto te permite fijar tu aire acondicionado en una configuración más alta sin afectar tu comodidad.
Cómo Cuidar del Ventilador Aquí tienes algunas sugerencias para el mantenimiento de tu ventilador. 1. Debido al movimiento natural del ventilador, algunas conexiones pueden aflojarse. Verifica las conexiones de soporte, soportes y accesorios de aspas dos veces al año. Verifica que estén seguros. (No es necesario desmontar el ventilador del techo). 2. Limpia tu ventilador con frecuencia, para que luzca como nuevo a pesar de los años.
TAMAÑO 36” VELOCIDAD VOLTIOS AMPERIOS VATIOS RPM PIES CÚB. X MIN. Baja 120 0.21 13 80 1450 Med 120 0.3 26 135 2200 Alta 120 0.42 49 205 3200 PESO NETO PESO BRUTO PIES CÚB 12.54 Lbs 14.19 Lbs 0.98 Estas son las medidas aproximadas. No incluyen ni el amperaje ni el vataje consumido por el kit de luces. Distribuido por Home Depot U.S.A., Inc. 2455 Paces Ferry Rd. N.W. Atlanta, Georgia 30339 Número del proveedor: 11688 Especificaciones 12.
Garantía limitada de por vida de Hampton Bay – Garantía de por vida para el motor Hampton Bay garantiza de por vida, a partir de la fecha de compra por el comprador original, que el motor del ventilador no presenta defectos de fabricación ni de material desde la fecha de salida de la fábrica.