530 171 San Lucas 56 in Ceiling Fan Owner’s Manual San Lucas Ventilador de Techo de 1,42 m Manual del Propietario
56” San Lucas Ceiling Fan by Hampton Bay Thank you for purchasing our ceiling fan. This product has been manufactured with the highest standards of safety and quality. The finish of this fan is weather resistant, but over time will naturally weather and fade. Date Purchased Table of Contents Store Purchased Safety Rules . . . . . . . . . . . . . . . . . . . . 1 UL Model No. 530-171 Unpacking Your Fan . . . . . . . . . . . . . . 2 Installing Your Fan . . . . . . . . . . . . . . . 3 Serial No.
Safety Rules - Read and Save These Instructions 1. To reduce the risk of electric shock, insure electricity has been turned off 10. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be at the circuit breaker or fuse box before beginning. spread apart with the grounded conductor and the equipment-grounding 2.
Unpacking Your Fan 5 2 Unpack your fan and check the contents. You should have the following items: 8 11 A B 1 9 3 12 C 6 7 4 1. 2. 3 4. 5. Set of blades (5) Canopy assembly Ball/downrod assembly (1) & extra downrod (1) Coupling cover Fan motor assembly WARNING DO NOT INSTALL OR USE FAN IF ANY PART IS DAMAGED OR MISSING. CALL TOLL FREE 1-877-902-5588. 2 6. 7. 8. 9. 10. 11. 12. 13.
Installing Your Fan Tools Required Provide Strong Support Figures 1~3 are examples of different ways to mount the outlet box. Phillips screwdriver, straight slot screwdriver, step ladder and wire cutters. Recessed Outlet Box Mounting Options Ceiling Mounting Plate Figure 3 Outlet Box If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers.
Hanging the Fan REMEMBER to turn off the power. Follow the steps below to hang your fan properly. 1. Remove the decorative canopy bottom cover from the canopy by turning the cover counter clockwise. (Figure 5) 2. Remove the mounting bracket from the canopy by loosening the two screws on the bottom of the mounting bracket a half turn from the screw head and turning the canopy counter clockwise. (Figure 5) 3. Remove the clevis pin, cotter pin and set screws from the top of the motor assembly. (Figure 6) 4.
Changing the Downrod (Optional) NOTE: Your fan comes with a 4" downrod attached to the hanger ball. In addition you have been provided with a 6" downrod to use if desired. If you choose to use the 6" downrod, perform the following steps: 1. Remove the hanger ball from the 4" downrod by loosening the set screw at the top of the downrod which holds the hanger ball to the downrod. 2. Slide the hanger ball down the downrod and remove the support pin. 3.
Making the Electrical Connections receiver. Secure the wire connections with the plastic wire connecting nuts provided. Frequency Switch WARNING TO AVOID POSSIBLE ELECTRICAL SHOCK, BE SURE ELECTRICITY IS TURNED OFF AT THE MAIN FUSE BOX BEFORE WIRING. If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. This remote control unit is equipped with 16 code combinations to prevent possible interference from or to other remote units.
WARNING BLACK BLACK WHITE SUPPLY CIRCUIT Ground Conductor Outlet Box GREEN WHITE WHITE BLUE BLACK BLACK BLUE WHITE Green Ground Lead Ground to Downrod CHECK TO SEE THAT ALL CONNECTIONS ARE TIGHT, INCLUDING GROUND, AND THAT NO BARE WIRE IS VISIBLE AT THE WIRE NUTS. EXCEPT FOR THE GROUND WIRE. WARNING ELECTRICAL DIAGRAMS ARE FOR REFERENCE ONLY. OPTIONAL USE OF ANY LIGHT KIT SHALL BE UL LISTED AND MARKED SUITABLE FOR USE WITH THIS FAN.
Attaching the Fan Blades CAUTION REMOVE THE 3 SCREWS FROM THE MOTOR SUPPORT PLATE, DISCARD THE 3 SCREWS AND MOTOR SUPPORT PLATE. 1. Attach blades to blade arm using the screws with rubber washers provided (Fig. 13). Start a screw into the blade arm, do not tighten. Repeat for the 2 remaining screws and washers. Screws with Rubber Washer Motor Tab Blade Slot Blade Arm Blade Arm Figure 13 2. Tighten each screw securely starting with the center screw. Make sure the blade is straight.
Blade Balancing The following procedure should correct most fan wobble. Check after each step. Installing the Mounting Plate Touching Ceiling 1. Remove 1 of the 3 screws from the mounting ring and loosen the other 2 screws. (Do not remove) 1. Check that all blade and blade bracket screws are secure. 2. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades.
Installing the Light Kit CAUTION BEFORE STARTING INSTALLATION, DISCONNECT THE POWER BY TURNING OFF THE CIRCUIT BREAKER OR REMOVING THE FUSE AT FUSE BOX. TURNING POWER OFF USING THE FAN SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRIC SHOCK. NOTE LIGHT BULBS HAVE NO WARRANTY; CAN BE PURCHASED AT ANY HOME DEPOT STORE. 1. While holding the light holder under your fan, make the polarized plug connections: -White to white -Black to black 2. Install the light holder onto the mounting plate with 3 screws provided.
Operating Your Transmitter Installing the Battery: Restore power to the ceiling fan and test for proper operation. Install 12V MN21/A23 battery (not included), to prevent damage to transmitter, remove the battery if not used for long periods. 1. "HI, MED, LOW" buttons: These three buttons are used to set the fan speed as follows: LOW=Low speed, MED= Medium speed HI=High speed Figure 20 2. "OFF" button: This button turns the fan off. 3.
Speed settings for warm or cool weather depend on factors such as the room size, ceiling height, number of fans, etc. The Reverse switch is located on the top of motor housing. Slide the switch to the Left for warm weather operation. Slide the switch to the Right for cool weather operation. NOTE WAIT FOR FAN TO STOP BEFORE CHANGING THE SETTING OF THE SLIDE SWITCH. Warm weather - (Counter-Clockwise direction) A downward air flow creates a cooling effect.(Fig.
Care of Your Fan Troubleshooting Here are some suggestions to help you maintain your fan. 1. Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) PROBLEM SOLUTION Fan will not start 1. Check main and branch circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. 3.
Specifications FAN SIZE SPEED VOLTS AMPS LOW 56” MED. HIGH 120 WATTS RPM CFM 0.38 20 75 1650 0.51 41 115 3075 0.54 66 150 4071 These are approximate measures. They do not include Amps and Wattage used by the light kit. 14 N.W. G.W. C.F. 15.1 Kgs (33.31 lbs) 16.82 Kgs (37.10 lbs) 2.
Lifetime Limited Warranty (lifetime warranty on motor) The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser.
