325 475 Beverley II 52 in Ceiling Fan Owner’s Manual Beverley II Ventilador de Techo de 1,32 m Manual del Propietario
Beverley II by Hampton Bay ®
52” BeverleyII Thank you for purchasing our ceiling fan. This product has been manufactured with the highest standards of safety and quality. Ceiling Fan by Hampton Bay Date Purchased Table of Contents Store Purchased Safety Rules . . . . . . . . . . . . . . . . . . . . 1 Model No. 325-475 Unpacking Your Fan . . . . . . . . . . . . . . 2 Installing Your Fan . . . . . . . . . . . . . . . 3 Serial No. Installing the Light Kit. . . . . . . . . . . . .10 Operating Your Fan . . . . . . . . . . . . . .
Safety Rules - Read and Save These Instructions 1. To reduce the risk of electric shock, insure electricity has been turned off 10. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be at the circuit breaker or fuse box before beginning. spread apart with the grounded conductor and the equipment-grounding 2.
Unpacking Your Fan Unpack your fan and check the contents. You should have the following items: 6 2 10 A B 7 3 1 1. 2. 3. 4. 5. 4 8 5 9 Set of blades (5) Canopy assembly Ball/downrod assembly Coupling cover Fan motor assembly WARNING DO NOT INSTALL OR USE FAN IF ANY PART IS DAMAGED OR MISSING. CALL TOLL FREE 1-877-902-5588. 2 11 6. 7. 8. 9. 10. 11. 12.
Installing Your Fan Tools Required Provide Strong Support Figures 1~3 are examples of different ways to mount the outlet box. Phillips screwdriver, straight slot screwdriver, step ladder and wire cutters. Recessed Outlet Box Ceiling Mounting Plate Figure 3 Mounting Options Outlet Box If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers.
Hanging the Fan 5. Align the holes at the bottom of the downrod with the holes in the coupling on top of the motor housing (Figure 6). Carefully insert the REMEMBER to turn off the power. Follow the clevis pin through the holes in the collar and steps below to hang your fan properly. downrod. Be careful not to jam the clevis pin against the wiring inside the downrod. Insert 1.
Installing Fan to the Electrical Box UL Listed Outlet Box WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL INJURY. MOUNT FAN ONLY TO AN OUTLET BOX OR SUPPORTING SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT AND USE THE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX. 1. Pass the 120-volt supply wires through the center hole in the ceiling mounting bracket as shown in Figure 7. 2.
If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. Follow the steps below to connect the fan to your household wiring. Use the wire nuts supplied with your fan. Secure the wire nuts with electrical tape. Make sure there are no loose strands or connections. 1. Connect the ground conductor of the 120V supply (this may be a bare wire or a wire with green colored insulation) to the green ground lead(s) of the fan. (Figure 9) 2.
Finishing the Fan Installation Outlet Box 1. Tuck connections neatly into ceiling outlet box. 2. Slide the canopy up to mounting bracket and place the key hole on the canopy over the screw on the mounting bracket, turn canopy until it locks in place at the narrow section of the key holes. (Fig. 10) 3. Align the circular hole on canopy with the remaining hole on the mounting bracket, secure by tightening the two set screws.
Attaching the Fan Blades CAUTION MOTOR IS SHIPPED WITH RUBBER PACKING MOUNTS TO PREVENT MOVEMENT DURING TRANSPORTATION. REMOVE 5 RUBBER PACKING MOUNTS FROM FAN MOTOR ASSEMBLY AND DISCARD PRIOR TO ATTACHING BLADE ARMS. (FIG. 11) 1. Attach blades to blade arm using the screws with fiber washers provided (Fig. 12). Start a screw into the blade arm, do not tighten. Repeat for the 2 remaining screws and washers. Motor Screws Tab Rubber Packing Mounts Blade Arm Figure 11 Slot 2.
Blade Balancing The following procedure should correct most fan wobble. Check after each step. Touching Ceiling 1. Check that all blade and blade bracket screws are secure. 2. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades. Measure from a point on the center of each blade to the point on the ceiling. Measure this distance as shown in Figure 14.
Installing the Mounting Plate Installing the Light Kit 1. Remove 1 of 3 screws from the mounting ring and loosen the other 2 screws. (Do not remove) CAUTION 2. Place the key holes on the mounting plate over the 2 screws previously loosened from the mounting ring, turn mounting plate until it locks in place at the narrow section of the key holes. Secure by tightening the 2 screws previously loosened and the one previously removed. (Fig.
Fan without Light Kit (Optional) CAUTION BEFORE STARTING INSTALLATION, DISCONNECT THE POWER BY TURNING OFF THE CIRCUIT BREAKER OR REMOVING THE FUSE AT FUSE BOX. TURNING POWER OFF USING THE FAN SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRIC SHOCK. Wire Connection Plugs Screws Mounting Plate 1. Holding the switch housing under your fan, snap the wire connection plugs together . 2. Install the switch housing to the mounting plate with screws provided. (Fig.
Operating Your Fan NOTE WAIT FOR FAN TO STOP BEFORE REVERSING THE DIRECTION OF THE BLADE ROTATION. Turn on the power and check the operation of your fan. There are two pull chains available in your fan: Warm weather - (Counter-Clockwise direction) A downward air flow creates a cooling effect as shown in Figure 19. This allows you to set your air conditioner on a higher setting without affecting your comfort. 1.
Care of Your Fan Troubleshooting Here are some suggestions to help you maintain your fan. 1. Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) PROBLEM SOLUTION Fan will not start 1. Check main and branch circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing.
Specifications FAN SIZE SPEED VOLTS AMPS LOW 52” MED. HIGH 120 WATTS RPM CFM 0.20 10 57 1716 0.35 30 106 3419 0.48 58 154 4884 These are approximate measures. They do not include Amps and Wattage used by the light kit . 14 N.W. G.W. C.F. 10.8 kgs (23.76 lbs) 12.3 kgs (27.06 lbs) 2.
Hampton Bay Lifetime Limited Warranty (lifetime warranty on motor) The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser.
