322-274 Sussex II 52 in Ceiling Fan Owner’s Manual Sussex II Ventilador de Techo de 1,32 m Manual del Propietario
Sussex II by Hampton Bay ®
52” Sussex II Thank you for purchasing our ceiling fan. This product has been manufactured with the highest standards of safety and quality. Ceiling Fan by Hampton Bay Date Purchased Table of Contents Store Purchased Safety Rules . . . . . . . . . . . . . . . . . . . . 1 Model No. 322-274 Unpacking Your Fan . . . . . . . . . . . . . . 2 Installing Your Fan . . . . . . . . . . . . . . . 3 Serial No. Installing the Light Kit. . . . . . . . . . . . . 10 Operating Your Transmitter . . . . . . . . . .
Safety Rules - Read and Save These Instructions 1. To reduce the risk of electric shock, insure electricity has been turned off 10. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be at the circuit breaker or fuse box before beginning. spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and ungrounded conductor on the 2.
Unpacking Your Fan Unpack your fan and check the contents. You should have the following items: 5 2 6 3 7 8 4 Set of blades (5) Canopy assembly Ball/downrod assembly Coupling cover Fan motor assembly Mounting plate WARNING DO NOT INSTALL OR USE FAN IF ANY PART IS DAMAGED OR MISSING. CALL TOLL FREE 1-877-902-5588. 2 A B 10 1 1. 2. 3. 4. 5. 6. 9 7. 8. 9. 10. 11. 12.
Installing Your Fan Tools Required Provide Strong Support Figures 1~3 are examples of different ways to mount the outlet box. Phillips screwdriver, straight slot screwdriver, step ladder and wire cutters. Recessed Outlet Box Mounting Options Ceiling Mounting Plate Figure 3 Outlet Box If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers.
Hanging the Fan 5. Align the holes at the bottom of the downrod with the holes in the coupling on top of the motor housing (Figure 6). Carefully insert the REMEMBER to turn off the power. Follow the clevis pin through the holes in the collar and steps below to hang your fan properly. downrod. Be careful not to jam the clevis pin against the wiring inside the downrod. Insert 1.
Installing Fan to the Electrical Box WARNING UL Listed Outlet Box THE TAB IN THE RING MUST REST IN THE GROOVE OF THE HANGER BALL AS FIGURE 8. FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING. WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL INJURY. MOUNT FAN ONLY TO AN OUTLET BOX OR SUPPORTING SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT AND USE THE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX. 1.
Making the Electrical Connections 3. (Figure 11) Receiver to house supply wires electrical connections: Connect the black (hot) wire from the ceiling to the black wire marked "AC in L" from he receiver. Connect the white (neutral) wire from the ceiling to the white wire marked "AC in N" from the receiver. Secure the wire connections with the plastic wire connecting nuts provided.
WARNING BLACK BLACK WHITE SUPPLY CIRCUIT Ground Conductor Outlet Box GREEN WHITE WHITE BLUE BLACK BLACK BLUE WHITE Green Ground Lead Ground to Downrod CHECK TO SEE THAT ALL CONNECTIONS ARE TIGHT, INCLUDING GROUND, AND THAT NO BARE WIRE IS VISIBLE AT THE WIRE NUTS. EXCEPT FOR THE GROUND WIRE. WARNING MAKE SURE THE TAB ON THE MOUNTING BRACKET PROPERLY SITS IN THE GROOVE IN THE HANGER BALL BEFORE ATTACHING THE CANOPY TO THE BRACKET BY TURNING THE HOUSING UNTIL IT DROPS INTO PLACE.
Attaching the Fan Blades CAUTION Rubber Packing Mounts REMOVE THE 3 SCREWS FROM THE MOTOR SUPPORT PLATE, KEEP THE 3 SCREWS FOR FUTURE USE AND DISCARD THE MOTOR SUPPORT PLATE. (Fig. 13) Motor Blade 1. Remove and discard the 3 rubber packing mounts from the center band. 2. Insert the blade through the slots in the bottom band. (Fig. 14) 3. Align the holes from the blade to the holes from the motor and secure in place with screws and fiber washers provided. (Fig.
Attaching the Mounting Plate Blade Balancing (if fan wobble is present after fan is completely assembled) Touching Ceiling 1. Install the mounting plate to the mounting ring with the 3 screws previously removed from the motor support plate. Be sure to tighten all screws. (Fig. 17) The following procedure should correct most fan wobble. Check after each step. 1. Check that all blade and blade bracket screws are secure. 2. Most fan wobble problems are caused when blade levels are unequal.
Installing the Light Kit CAUTION BEFORE STARTING INSTALLATION, DISCONNECT THE POWER BY TURNING OFF THE CIRCUIT BREAKER OR REMOVING THE FUSE AT FUSE BOX. TURNING POWER OFF USING THE FAN SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRIC SHOCK. 6. Restore power and your light kit is ready for operation. NOTE LIGHT BULBS HAVE NO WARRANTY; CAN BE PURCHASED AT ANY HOME DEPOT STORE. 1. Remove the 1 of 3 screws from the posts of the mounting plate and keep it for future use. Loosen the other 2 screws.
Operating Your Transmitter Installing the Battery: Restore power to the ceiling fan and test for proper operation. Install 12V MN21/A23 battery (included), to prevent damage to transmitter, remove the battery if not used for long periods. 1. "HI, MED, LOW" buttons: These three buttons are used to set the fan speed as follows: LOW=Low speed, MED= Medium speed HI=High speed ( WARNING: May explode or leak if recharged, disposed of in fire or dissected. Do not ingest.) Figure 21 2.
Installing the Transmitter Holder Speed settings for warm or cool weather depend on factors such as the room size, ceiling height, number of fans, etc. 1. Remove the two plugs from the holder. Note that the plugs have unique tabs that allows them to fit only in one hole. (Fig. 22) The reverse switch is located on the top of motor housing. Slide the switch to the left for warm weather operation. Slide the switch to the right for cool weather operation. 2. Attach the holder with the two screws provided.
Care of Your Fan Troubleshooting Here are some suggestions to help you maintain your fan. 1. Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) PROBLEM SOLUTION Fan will not start 1. Check main and branch circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. 3.
Specifications FAN SIZE SPEED VOLTS AMPS LOW 52” MED. HIGH 120 WATTS RPM CFM 0.32 13 61 1768 0.44 32 105 3149 0.49 59 148 4725 These are approximate measures. They do not include Amps and Wattage used by the light kit. 14 N.W. G.W. C.F. 8.77 kgs (19.29 lbs) 9.75 kgs (21.45 lbs) 1.
Hampton Bay Lifetime Limited Warranty (lifetime warranty on motor) The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser.
