Instructions / Assembly

ManualsBrandsHampton Bay ManualsFlushmount Lights2-Light White Fluorescent Round Deco Ceiling Flushmount

FLUORESCENT FLUSH MOUNT FIXTURE

ASSEMBLY & INSTALLATION INSTRUCTIONS

Please read carefully and save these instructions, as you may need them at a later date.

CAUTION

Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.

GENERAL

All electrical connections must be in accordance with local and national electrical code (N.E.C) standards. If you

are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.

Remove the fixture and the mounting package from the box and make sure that no parts are missing by referencing

the illustrations on the installation instruction.

ASSEMBLY AND INSTALLATION

1. Turn off the power.

2. Remove the WOOD FRAME (19) with ACRYLIC LENS (18) from the FIXTURE PAN (11) by turning the

three CLIPS (9) outward.

3. Remove the lamps out from the LAMP BRACKETS (12) by pulling each LAMP BRACKET (12)

backwards. Then remove the 22/32 W BALLAST RECEPTACLES (13)&(14) from the LAMP

CONNECTORS (16)&(17).

4. Pull the SUPPLY WIRES (4 )&(6) and HOUSE GROUND WIRE (2) out from the OUTLET BOX (1).

5. Make the wiring corrections: connect the HOUSE GROUND WIRE (2) to the FIXTURE GROUND WIRE

(3); connect the WHITE SUPPLY WIRE (4) to the WHITE FIXTURE WIRE (5); connect BLACK

SUPPLY WIRE (6) to the BLACK FIXTURE WIRE (8) using WIRE CONNECTORS (7). Thread one of

the MOUNTING SCREWS (15) two full turns into the threaded hole on the OUTLET BOX (1). Carefully

tuck all wires back into the OUTLET BOX (1).

6. Locate the FIXTURE PAN (11) over the OUTLET BOX (1), positioning the MOUNTING SCREW (15)

through the large opening of the key hole slot and then twist to the narrow opening of the key hole slot. Feed

the other MOUNTING SCREW (15) through the long hole slot on the fixture pan and thread it into the

threaded hole on the OUTLET BOX (1). Then secure the FIXTURE PAN (11) to the OUTLET BOX (1) by

tightening the two MOUNTING SCREWS (15).

7. Note: Both ballasts leads are rated for use with both 32 W and 22 W Circline lamps, and each ballast

lead can be attached to either lamp provided with the fixture. Attach one BALLAST RECEPTACLE (13)

to the 22 W LAMP CONNECTOR (16). Attach the 22 W CIRCLINE LAMP (20) to FIXTURE PAN (11) by

pulling a LAMP BRACKET (12) backward and inserting the 22 W CIRCLINE LAMP (20). (Fig. 2) Pull

back the remaining LAMP BRACKETS (12) and insert the 22 W CIRCLINE LAMP (20).

8. Attach the 32 W CIRCLINE LAMP (21) to the fixture, by repeating Step 7 using the remaining BALLAST

RECEPTACLE (14).

9. Secure the WOOD FRAME (19) with the ACRYLIC LENS (18) to the FIXTURE PAN (11) by turning the

three CLIPS (9) inward.

INSTALLATION IS NOW COMPLETED

1. OUTLET BOX

2. HOUSE GROUND WIRE

3. FIXTURE GROUND WIRE

4. WHITE SUPPLY WIRE

5. WHITE FIXTURE WIRE

6. BLACK SUPPLY WIRE

7. WIRE CONNECTOR

8. BLACK FIXTURE WIRE

9. CLIP

10. ELECTRONIC BALLAST

11. FIXTURE PAN

12. LAMP BRACKET

13. BALLAST RECEPTACLE

14. BALLAST RECEPTACLE

15. MOUNTING SCREW

16. 22 W LAMP CONNECTOR

17. 32 W LAMP CONNECTOR

18. ACRYLIC LENS

19. WOOD FRAME

20. 22 W CIRCLINE LAMP

21. 32 W CIRCLINE LAMP

Summary of content (2 pages)

PAGE 1
FLUORESCENT FLUSH MOUNT FIXTURE ASSEMBLY & INSTALLATION INSTRUCTIONS Please read carefully and save these instructions, as you may need them at a later date. CAUTION Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock. GENERAL All electrical connections must be in accordance with local and national electrical code (N.E.C) standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician. 1.
PAGE 2
LAMPARA FLUORESCENTE PARA TECHO INSTRUCCIONES DE MONTAJE E INSTALACION Por favor, lea cuidadosamente y guarde estas instrucciones, ya que puede necesitarlas posteriormente. PRECAUCION Desactive la electricidad del cortacircuitos antes de empezar la instalación de la lámpara para evitar una descarga eléctrica. INFORMACION GENERAL 1. CAJA DE CONEXION 2. ALAMBRE A TIERRA DE LA CAJA 3. ALAMBRE A TIERRA DE LA LAMPARA 4. CABLE BLANCO DEL SUMINISTRO 5. CABLE BLANCO DE LA LAMPARA 6.