Use and Care Manual
LINE VOLTAGE FLEXIBLE TRACK LIGHTING
INSTRUCTION MANUAL
Please read carefully and save these instructions, as you may need them at a later date.
SAFETY
WARNING: RISK OF ELECTRIC SHOCK
Disconnect the electrical supply circuit before installing light fixture.
GENERAL
All electrical connections must be in accordance with local codes, ordinances or national electrical codes. If you are unfamiliar
with methods of installing electrical wiring, secure the services of a qualified electrician. Before starting installation, disconnect
the power by turning off the circuit breaker or removing the fuse at the fuse box.
INSTALLATION INSTRUCTIONS
CAUTION: MAKE SURE POWER IS TURNED OFF AT THE ELECTRICAL PANEL BOX BEFORE BEGINNING YOUR
INSTALLATION. TURNING POWER OFF AT WALL SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRICAL SHOCK.
GENERAL
1. Be sure to read these installation instructions and review the diagrams thoroughly before installing the light fixture.
2. All electrical connections must be in accordance with local codes and the National Electrical Code. If you are unfamiliar
with methods of installing electrical wiring, secure the services of a qualified licensed electrician.
3. These fixtures are intended to be mounted to a 4" square x 2-1/8" deep metal octagon outlet box. The box must be directly
supported by the building structure.
4. Before starting the installation, disconnect the power by turning off the circuit breaker or by removing the appropriate fuse
at the fuse box. Turning the power off using the light switch is not sufficient to prevent electrical shock.
Note: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and
situations that may occur. It must be understood that common sense, caution and care are factors that cannot be built into
any product. These factors must be supplied by the person(s) caring for, installing and operating the fixture.
IMPORTANT SAFETY INSTRUCTIONS
1. Read all instructions.
2. Do not install this lighting system in a damp or wet location.
3. Before energizing make sure that the lighting system is clear of all material which could cause a direct short and check all
electrical connections to make sure they are tight.
4. CAUTION – Hot surface, keep away from curtains and other combustible materials.
5. Lighted lamp is hot! Do not touch lamp at any time. Use a soft cloth or relamping tools (see diagram), Oil from skin may
damage lamp. Turn off power and allow bulbs to cool before replacing.
6. Lamp gets hot quickly! Contact only switch or plug when turning on. Do not touch hot lamp lens.
7. Do not conceal or extend bus-bar conductors through a building wall.
8. Do not install any part of this system (TRACK) less than 7 feet (2.2m) above floor.
9. To reduce the risk of fire and burns, do not install this lighting system where non insulated open bus-bar conductors can be
shorted or contact any conductive metals.
10. To reduce the risk of fire and overheating, make sure all connections are tight.
11. Do not install any lamps closer than 6 inches (15.25cm) from any curtain or similar combustible material.
12. Turn off electrical power before modifying the light system in anyway.
13. Use minimum 20” spacing between stanchions when using 4 stanchions.
14. For use with Hampton Bay EC series and HB series line voltage flexible track only.
Do not cut any track sections.
15. CAUTION – To reduce the risk of a burn during relamping, remove from the track before relamping.
16. This track system is to be supplied by a single branch 120 volt circuit.
17. Disconnect electrical power before adding to or changing the configuration of the track.
18. Do not attempt to energize anything other than lighting track fixture on the track. To reduce the risk of fire and electric
shock, please do not attempt to connect power tools, extension cords, appliances and the like to the track.
19. Save these instructions and refer to them when additions to or changes in the track configuration are made.
READ AND SAVE THESE INSTRUCTIONS
Tools Needed: Slotted screwdriver, Adjustable wrench, Electrical Hand drill, Step ladder, Wire cutters, Wiring supplies as
required by electrical code.
HOW TO INSTALL:
INSTALL FIXTURE
1. Make sure that the power is turned off.
2. Remove the retaining caps from the fixtures.
3. Align the two tabs of the track fixture adaptor to the two slots on the flexible track.
4. Close the fixture adapters and replace the retaining caps making sure that the connection is secure.
RELAMPING THE BULB
1. Make sure that the power is turned off.
2. Make sure that the bulb is cool before relamping the fixture.
3. Use relamping tool if necessary to remove and install bulbs.(Note: Keep relamping tool for future use)
(For diagram 1,2: a, Remove the decorative ring. b, Twist to unplug GU10 bulb from the socket. c, Replace with new
bulb and install the decorative ring. NOTE: when installing decorative ring – Turn the decorative ring clockwise for a
secure and tight fit.)
4. Restore electrical power.
CAUTION: Refer to the relamping label located near the lampholder for recommended maximum wattage.
Power cano
py
Track
R
eta
i
n
i
ng
cap
Retainin
g
ca
p
bulb
Relam
p
in
g
tool
Power canop
y
, track, ceilin
g
support stems
(
sold separatel
y
)
Fixture ada
p
te
r
diagram 1
diagram 2
Decorative ring
566C