Installation Guide

ManualsBrandsHampton Bay ManualsAssembled Kitchen CabinetsWestfield Feather White Shaker Stock Assembled Wall Kitchen Cabinet (18 in. W x 12 in. D x 30 in. H)

Table Of Contents

PASO 4: Comience la instalación del gabinete de esquina cuadrada

Coloque el gabinete de esquina cuadrada y el gabinete adyacente en su lugar con referencia

a la tabla de especicaciones de relleno y extracción en la página 1. Establecer la cantidad

adecuada de extracción es fundamental para una instalación exitosa. Conrme que el

gabinete de la esquina cuadrada esté nivelado y aplomado. Si es necesario, agregue cuñas

para nivelar. Retire el gabinete adyacente para dejar espacio para la instalación.

PASO 5: Instalación completa del gabinete de esquina cuadrada

Ubique los montantes de pared predeterminados y las marcas de transferencia al interior

del gabinete. Perfore a través de la parte posterior del gabinete y dentro del montante de

la pared con una broca de 3/32” de diámetro y aproximadamente 2” de profundidad. Los

oricios no deben estar a menos de 2” de cualquier borde vertical interior del gabinete. Inserte

los tornillos con cabeza de arandela redonda de 2 ½” en los oricios hasta que estén casi

apretados. Verique para asegurarse de que el gabinete permanezca nivelado y aplomado.

Ajuste según sea necesario antes de apretar completamente los tornillos.

NOTA: Nunca utilice clavos para montar los gabinetes. El uso de clavos puede anular la garantía de

fábrica, escrita o implícita.

PASO 6: Determine el ancho del relleno

Siguiendo el diseño, coloque el gabinete adyacente al lado del gabinete base de esquina

cuadrada que se instaló. El ancho del relleno, Z, ahora se puede determinar de acuerdo con

la tabla de especicaciones en la página 1 y su diseño. Rasgue el relleno al ancho deseado

si es necesario.

PASO 7: Instalación del relleno

Con el relleno del ancho deseado, sujete el relleno al lado apropiado del marco frontal del

gabinete adyacente. Alinee el relleno verticalmente con el marco y asegúrese de que la cara

del relleno esté al ras con la cara del marco. Taladre dos oricios de 3/32” de diámetro a

través del marco frontal y en el relleno cerca de la parte superior e inferior. Luego, inserte y

apriete tornillos para madera de cabeza plana o de moldura de 2 ½” para jar el relleno al

marco del gabinete adyacente. (NOTA: Si el ancho del relleno es inferior a una pulgada, use

tornillos más cortos).

PASO 8: Instalación del gabinete adyacente

Coloque el gabinete adyacente y el conjunto de relleno en su lugar. Verique el gabinete

para asegurarse de que esté nivelado y aplomado usando cuñas si es necesario. Asegúrese

de que el relleno esté correctamente alineado con el marco frontal del gabinete de esquina

cuadrada. Siga el Paso 5 para asegurar el gabinete adyacente a la pared.

Paso 9: Conecte la esquina cuadrada al conjunto de gabinete

adyacente/de relleno

Una vez que el gabinete adyacente se haya asegurado a la pared, use abrazaderas para unir de manera segura los

gabinetes. Asegúrese de que el conjunto de gabinete adyacente y de relleno aún esté correctamente alineado con el

gabinete de esquina cuadrada. Marque dos ubicaciones en el interior del marco frontal del gabinete de esquina cuadrada

que coincidan con el centro del relleno. Taladre dos oricios de 3/32” de diámetro a través del marco frontal del gabinete

de esquina cuadrada y en el relleno cerca de la parte superior e inferior. Luego, inserte y apriete tornillos para madera de

cabeza plana o de moldura de 2 ½” para jar el relleno y el gabinete adyacente al gabinete de esquina cuadrada.

(6.18.13) SCB INSTRUCTIONS A5131

STEP 5

STEP 6

STEP 7

Attach the blind panel to the face frame

using the recommended (8) #6 x 1/2" flat

head screws. These screws must be

purchased separately. Reattach the door

and drawer front to the cabinet.

Place the predrilled blind panel onto the

face frame using the markings placed on

the face frame in the last step. Mark the

predrilled hole locations from the blind

panel onto the face frame. Remove the

blind panel and predrill the face frame (8)

places with a 7/64" diameter drill bit, 1/2"

deep.

Position the Square Corner Base cabinet

with reference to the specifications on

page one. Do not secure to the wall yet.

SQUARE CORNER

CABINET

ADJACENT

CABINET

Filler Board

Wall

=Open Space

MARK

(8) HOLE

LOCATIONS

ONTO THE

FACE FRAME.

Attach panel to the face frame

using the (8) #6 x 1/2"

flat head screws.

(6.18.13) SCB INSTRUCTIONS A5131

STEP 8

STEP 9

STEP 10

Measure from the corner to the first wall stud mark.

Transfer this measurement to the inside of the wall corner

cabinet. Mark the placement of the next wall stud. Drill

through the wall cabinet back into the prelocated studs

with a 3/32" diameter drill bit, approximately 2" deep. The

holes should be positioned 3/4" down from the inside top

of the cabinet but should come no closer than 2" to any

inside vertical edge of the cabinet. Cement, block, brick,

or tile walls will require anchors for screws or toggle bolts.

These will need to be purchased separately if needed.

Insert #10 x 2 1/2" screws into the holes until they are

nearly tight. Do not tighten the screws until you have

finished all final leveling and shimming as needed. Check

the front sides and tops of all cabinets with a level. After

the cabinet is level and plumb, tighten the installation

screws.

NOTE: Never use nails to mount cabinets. The use of

nails may void your factory warranty, written or implied.

Once the square corner base cabinet is positioned in step

5, confirm that the cabinet is sitting level and straight.

Remove the adjacent cabinet to allow for room to install

the square corner base cabinet. If needed, add shims to

level the cabinet.

Level

Following your design layout, replace the adjacent cabinet

next to the square corner base cabinet that has been

installed. The width of the filler, Z, can now be determined

in accordance with the specifications on page one and

your design layout.

*Filler Board is located under cabinet with Blind Cover

Panel.

SQUARE CORNER

CABINET

ADJACENT

CABINET

Filler Board

Wall

=Open Space

(6.18.13) SCB INSTRUCTIONS A5131

STEP 8

STEP 9

STEP 10

Measure from the corner to the first wall stud mark.

Transfer this measurement to the inside of the wall corner

cabinet. Mark the placement of the next wall stud. Drill

through the wall cabinet back into the prelocated studs

with a 3/32" diameter drill bit, approximately 2" deep. The

holes should be positioned 3/4" down from the inside top

of the cabinet but should come no closer than 2" to any

inside vertical edge of the cabinet. Cement, block, brick,

or tile walls will require anchors for screws or toggle bolts.

These will need to be purchased separately if needed.

Insert #10 x 2 1/2" screws into the holes until they are

nearly tight. Do not tighten the screws until you have

finished all final leveling and shimming as needed. Check

the front sides and tops of all cabinets with a level. After

the cabinet is level and plumb, tighten the installation

screws.

NOTE: Never use nails to mount cabinets. The use of

nails may void your factory warranty, written or implied.

Once the square corner base cabinet is positioned in step

5, confirm that the cabinet is sitting level and straight.

Remove the adjacent cabinet to allow for room to install

the square corner base cabinet. If needed, add shims to

level the cabinet.

Level

Following your design layout, replace the adjacent cabinet

next to the square corner base cabinet that has been

installed. The width of the filler, Z, can now be determined

in accordance with the specifications on page one and

your design layout.

*Filler Board is located under cabinet with Blind Cover

Panel.

SQUARE CORNER

CABINET

ADJACENT

CABINET

Filler Board

Wall

=Open Space

10/15/2023 A5168-ESP-Rev 1

(6.18.13) SCB INSTRUCTIONS A5131

STEP 11

STEP 12

STEP 13

With the adjacent cabinet removed, the Filler Board

can be clamped to the square corner cabinet in the

position marked in the previous step. Drill two 3/32”

holes into the filler board through the face frame of

the cabinet. Then use 2 #8 cabinet screws of the

appropriate length depending on the width of your

filler board if you cut to fit your design layout. If the

Filler Board’s width was not cut down, use 2” long

#8 cabinet screws.

Once the square corner cabinet has been installed,

the adjacent base cabinets can now be installed.

Start installing the base cabinets in the corner.

Using clamps, align and join the cabinets together

at the face frames. Make sure that the face frames

align both on the face and vertically.

Check the cabinet to ensure it is level and plumb.

Shim to fill uneven areas between the floor and

base of the cabinet and between the wall and the

back of the cabinet. Failure to do this step could

result in damage to the cabinet.

Follow Step 9 to secure adjacent cabinet to the

wall.

With the adjacent cabinet positioned next to the

installed square corner cabinet, mark the location

of the filler board on the inside of the square corner

cabinet face frame.

SQUARE CORNER

CABINET

ADJACENT

CABINET

Filler Board

Wall

=Open Space

Pencil

SQUARE CORNER

CABINET

Filler Board

Wall

Clamp

Shims

Muro

Cuñas

GABINETE

ADYACENTE

GABINETE

ADYACENTE

ARMOIRE

ADJACENTE

Gabinete de

esquina cuadrado

Gabinete de esquina

cuadrado

Tablero de

relleno

Tablero de

relleno

= Espacio abierto