Instructions / Assembly

THANK YOU
We appreciate the trust and condence you have placed in Hampton Bay through the
purchase of this add on wireless motion sensor. We strive to continually create quality
products designed to enhance your home. Visit us online to see our full line of products
available for your home improvement needs. Thank you for choosing Hampton Bay!
USE AND CARE GUIDE
ADD ON WIRELESS MOTION SENSOR
Illustrations may vary from actual unit.
Safety Information
1. Please read and understand this entire manual before attempting to assemble, install,
or operate this sensor.
WARNING: To prevent possible SERIOUS INJURY or DEATH never allow small children near
batteries. If battery is swallowed, immediately notify a doctor.
WARNING: DO NOT mix old and new batteries. DO NOT mix battery types - such as alkaline, heavy
duty, and rechargeable - in a single device. Battery leakage may occur.
WARNING: DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES MAY EXPLODE OR LEAK.
NOTE: The range of the wireless doorbell can vary with location, temperature, and battery
condition.
This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada.
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
The user is cautioned that changes or modications not expressly approved by the party
responsible for regulatory compliance could void the user’s authority to operate the
equipment.
Care and Cleaning
 Use a dry cloth to clean the motion sensor.
 Do not use cleaners or polishes.
 Do not use any uids on the motion sensor.
Pre-Installation
TOOLS REQUIRED
Phillips screwdriver Small athead screwdriver Drill
1/16 in. (1.5 mm) drill bit Safety goggles
HARDWARE INCLUDED
Part Description Quantity
AA Screw 2
PACKAGE CONTENTS
Part Description Quantity
A Sensor (batteries not included) 1
Installation
1
Installing the batteries into
the motion sensor

Remove the screw on the back
of the motion sensor (A) using a
small, Phillips screwdriver (not
included).

Install two “AAA” batteries. Ensure
batteries are oriented correctly.

Replace the cover on the back of
the motion sensor (A) and tighten
the screw.
2
Syncing the sensor and
doorbell

Press and hold the “SYNC” button
on the doorbell (not included)
until the doorbell sounds a
“Beep-Beep”.

Press the “SYNC” button on the
bottom of the sensor (A) within 30
seconds of pressing the doorbell
“SYNC” button.
RANGE
ON-TIME
MAX
TEST 1 5
(MINS)
MIN
SYNC
SYNC
SYNC – PRESS
AND RELEASE.
RESET – HOLD
10 SECONDS.
TUNE – HOLD
1 SECOND.
30
3
Testing the sensor and
doorbell
In most cases, testing of the motion
sensor requires two people; one person
to activate the sensor (A) and the other
to listen for the doorbell to sound.

Slide the ON-TIME switch to the
“TEST” position.

Temporarily position the sensor (A)
near the desired mounting location.

While someone is listening for the
doorbell to sound, walk in front of
the sensor (A). The red LED on the
sensor (A) should ash and the
doorbell will sound “Beep-Beep”.
In the “TEST” position, all motion
must stop for 10 seconds before
the sensor (A) will activate the
doorbell again.

If the doorbell does not sound,
move the doorbell closer to the
sensor (A) and test again.
NOTE: Do not permanently mount the
sensor until the sensor and doorbell are
working properly.
ON-TIME
TEST 1 5
(MINS)
RANGE
ON-TIME
MAX
TEST 1 5
(MINS)
MIN
SYNC
4
Mounting the sensor
Attach the sensor (A) mounting bracket
to a sturdy surface using screws
(AA). Make sure the sensor (A) has an
unobstructed view.

Place the sensor mounting bracket
in the desired location and mark
the two screw holes. Attach with
the screws (AA).

If the sensor (A) was removed
from the mounting bracket, use a
Phillips screwdriver (not included)
to loosen the clamp screw on the
mounting bracket. Insert the swivel
ball on the sensor (A) into the
mounting bracket until it snaps into
place. Aim the sensor (A) toward
the area to be monitored and
tighten the clamp screw.
NOTE: Attach mounting bracket
vertically when attaching to a curved
surface.
IMPORTANT: The sensor must be rotated so the
controls are facing down.
Operation
1
Setting the sensor’s day
detect
The sensor (A) can be programmed to
operate during the daytime only (DAY
ONLY) or both day and night (DAY/NIGHT).

Remove the battery cover and
batteries from the sensor (A).

Slide the “DAY DETECT” switch
to the desired mode. Replace the
batteries and cover.
DAY DETECT
DAY DAY/
ONLY NIGHT
Warranty
3-YEAR LIMITED WARRANTY
WHAT IS COVERED
This product is guaranteed to be free of factory defective parts and workmanship for a
period of 3 years from date of purchase. Purchase receipt is required for all warranty
claims.
WHAT IS NOT COVERED
This warranty does not include expendable items (such as light bulbs, batteries, etc.), repair
service, adjustment and calibration due to misuse, abuse or negligence. Unauthorized
service or modication of the product or of any furnished component will void this warranty
in its entirety. This warranty does not include reimbursement for inconvenience, installation,
setup time, loss of use, unauthorized service, or return shipping charges. This warranty
is not extended to other equipment and components that a customer uses in conjunction
with this product.
Contact the Customer Service Team at 1-844-760-3644 or visit www.hamptonbay.com.
Questions, problems, missing parts?
Before returning to the store, call Hampton Bay Customer Service
8 a.m. - 5 p.m., CST, Monday - Friday
1-844-760-3644
HAMPTONBAY.COM
2
Setting the sensor’s range
The “RANGE” control increases and
decreases the sensitivity of the sensor
(A) as well as increases and decreases
the distance the sensor (A) will detect
movement.
NOTE: False triggering may happen if
the RANGE is set too high.

Adjust the “RANGE” control to
increase (MAX) or decrease (MIN)
the sensitivity.
RANGE
ON-TIME
MAX
TEST 1 5
(MINS)
MIN
SYNC
3
Setting the sensor’s on-time
The “ON-TIME” control determines the
amount of time that all motion must
be stopped before the sensor (A) will
activate the doorbell again.

Select the “ON-TIME” setting
desired:
 “TEST” - Motion must be
stopped for 10 seconds before
reactivation.
 “1 MIN” - Motion must be
stopped for 1 minute before
reactivation.
 “5 MIN” - Motion must be
stopped for 5 minutes before
reactivation.
RANGE
ON-TIME
MAX
TEST 1 5
(MINS)
MIN
SYNC
Specications
Power requirements
2x - Type “AAA” 1.5V battery (not included)
Troubleshooting
Problem Solution
The doorbell does not sound. Make sure batteries are installed according
to the diagram inside the sensor and
doorbell (if applicable).
Check the charge of the sensor and doorbell
batteries (if applicable) and replace if
necessary.
Make sure the plug-in doorbell has power
(if applicable).
Sensor and doorbell are not synced. Follow
Step 2 in the Installation section to sync.
The doorbell sounds at night. If a doorbell alert is not desired at night,
slide the day detect switch to the “DAY
ONLY” position.
The doorbell does not sound during
the day.
Slide the day detect switch to the “DAY/
NIGHT” position or move the sensor to an
area that receives more light.
The batteries seem okay, but the
doorbell does not work after installation.
Metal reduces transmission range. Use
1/4in. to 1/2 in. (6 to 13 mm) wood shims to
move the doorbell or sensor away from the
metal surface.
Concrete may reduce range. Move the
doorbell away from the concrete surface.
Locate the doorbell closer to the sensor.
208188-03A
A
A
A
AA
Model #HB-7773-02
A
A
A
A
A
AA
Operation