Item: 1001398739 Model: HB2583-35 USE AND CARE GUIDE ____________________________________ 5 LIGHT CHANDELIER Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. – 7 p.m., EST, Monday – Friday 8 a.m. – 6 p.m., EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM THANK YOU We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this chandelier.
Table of Contents Table of Contents Safety Information Warranty Pre-Installation Planning the Installation Tools Hardware Package Contents 2 2 2 3 3 3 3 4 Installation Operation Care and Cleaning Exterior Maintenance Interior Maintenance Troubleshooting 5 9 9 9 9 9 Safety Information Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box.
Pre-Installation PLANNING THE INSTALLATION Read all instructions before assembly and installation. Before starting installation of the fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box. To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard. NOTE: Keep your receipt and these instructions for Proof of Purchase.
Pre-Installation (continued) PACKAGE CONTENTS A C D B Part Description Quantity A Canopy 1 B Main Fixture Body 1 C Glass Shade 5 D Center Tube 1 4
Installation 1 Attaching the mounting bracket Thread two hex nuts (AA) onto the nipple (EE) to the midpoint. Thread the nipple (EE) in through the center hole of the mounting bracket (JJ) approximately 1/3 of the way. Do not tighten the hex nuts (AA). Pull the supply wires out from the outlet box.
Installation (continued) 3 Adjusting the chain length Thread the center tube (D) onto the coupling . Thread the top loop (II) onto the top of the main fixture body (B). Attach the chain (KK) to the top loop (II) using the chain link connector (DD). Raise the chain (KK) and the main fixture body (B) up to the outlet box to determine the desired length needed for installation. Identify the chain link that needs to be opened to remove the excess chain.
Installation (continued) 5 Threading the cord Feed the cord and fixture ground wire into the center hole of the screw collar loop (HH), through the nipple (EE), and then out of the outlet box. JJ FF HH Continue feeding the cord and fixture ground wire until there is no slack remaining. Cut off any excess cord and fixture ground wire, leaving 6 in. extending from the outlet box. Split and separate the fixture cord and strip off 3/8 in. of insulation from each wire.
Installation (continued) 7 Securing the canopy Slide the canopy (A) up the chain (KK), toward the outlet box, and up against the ceiling surface. Slide the threaded ring (CC) up the chain (KK) and thread it onto the screw collar loop (HH) to secure the canopy (A) flush against the ceiling surface. A CC HH KK 8 Assembling the fixture NOTE: Do not exceed a 60 watt incandescent .For more information on the proper lighting to use, see www.homedepot.com/lightingfacts.
Operation Turn on power at the circuit breaker or fuse box. Turn the light switch on to activate the fixture. Care and Cleaning EXTERIOR MAINTENANCE NOTE: Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully. Use a dry or slightly dampened clean cloth and wipe the surface of the fixture. INTERIOR MAINTENANCE Disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box.
Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. – 7 p.m., EST, Monday-Friday 8 a.m. – 6 p.m., EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM Retain this manual for future use.
Artículo: 1001398739 Modelo: HB2583-35 GUÍA DE USO Y MANTENIMIENTO ____________________________________ ARAÑA DE 5 LUCES Preguntas, problemas, o piezas faltantes? Antes de regresar a la tienda, llama al Servicio al Cliente de Hampton Bay 8 a.m. – 7 p.m., Hora del Este, Lunes – Viernes 8 a.m. – 6 p.m., Hora del Este, Sábado 1-855-HD-HAMPTON HAMPTONBAY.COM GRACIAS Le agradecemos la confianza que han depositado en Hampton Bay a través de la compra de esta araña de luces.
Tabla de Contenidos Tabla de Contenidos Información de Seguridad Garantía Pre-Instalación Planificación de la Instalación Herramienta Ferretería Contenido del Paquete 12 12 12 13 13 13 13 14 Instalación Operación Cuidado y Limpieza Mantenimiento Exterior Mantenimiento Interior Solución de Problemas 15 19 19 19 19 19 Información de Seguridad Antes de iniciar la instalación de este aparato o la eliminación de un accesorio anterior, desconecte la alimentación apagando el disyuntor o quitando el fusible
Pre-Instalación PLANIFICACIÓN DE LA INSTALACIÓN Lea todas las instrucciones antes del montaje e instalación. Antes de comenzar la instalación de la luminaria o el retiro de un artefacto anterior, desconecte la alimentación apagando el disyuntor o quitando el fusible en la caja de fusibles. Para evitar daños a este producto, montarlo en una superficie suave y no abrasiva, como una alfombra o cartón. NOTA: Guarde su recibo y estas instrucciones para comprobante de compra.
Pre-Instalación (continuado) CONTENIDO DEL PAQUETE A C D B Parte Descripción Cantidad A Cubierta 1 B Cuerpo Principal 1 C Pantalla de Vidrio 5 D Central Tubos 1 14
Instalación 1 Sujetando la ménsula de montaje Enrosque dos tuercas hexagonales (AA) en la boquilla (EE) hasta su punto medio aproximado. Enrosque la boquilla (EE) a través del agujero central de la ménsula de montaje (JJ) 1/3 aproximadamente de su profundidad. No apriete las tuercas hexagonales (AA). Saque los cables de alimentación de la caja de alimentación.
Instalación (continuado) 3 Ajustando la longitud de la cadena Enrosque la central tubos (D) en el tuerca de empalme. Enrosque el bucle superior (II) en la parte superior del cuerpo principal (B). Coloque la cadena (KK) a el bucle superior (II) con el eslabón conector (DD) de la cadena. Levante la cadena (KK) y el cuerpo principal (B) hasta la caja de alimentación para determinar la longitud deseada para la instalación.
Instalación (continuado) 5 Enhebrando el cable Pase el cordón y el cable a tierra del luminario en el agujero central del bucle roscado (HH), por el centro de la boquilla (EE), y fuera de la caja de alimentación. JJ FF HH Continúe pasando el cordón y el cable a tierra del luminario hasta que no quede exceso de cable ni de cordón. Corte cualquier exceso del cordón y del cable a tierra del luminario, dejando una longitud de 6 pulgadas (15,24 cm), que se extiende desde la caja de alimentación.
Instalación (continuado) 7 Asegurando la cubierta Deslice la cubierta (A) hasta la cadena (KK), hacia la caja de alimentación y contra la superficie del techo. Deslice el aro roscado (CC) hasta la cadena (KK) y enrósquelo en el bucle roscado (HH) para asegurar la cubierta (A) al ras contra la superficie del techo. A CC HH KK 8 Ensamblando la araña NOTA: No exceda una bombilla incandescente de 60. Para obtener más información sobre la iluminación adecuada que debe utilizar, consulte www.
Operación Conecte la alimentación en el disyuntor o caja de fusibles. Gire el interruptor de la luz para activar el aparato. Cuidado y Limpieza MANTENIMIENTO DEL EXTERIOR NOTA: No use limpiadores con químicos, solventes o abrasivos fuertes. Use sólo un paño seco para sacudir o limpiar con cuidado. Use un paño limpio y seco o ligeramente humedecido y limpie la superficie de la linterna.
Preguntas, problemas, o piezas faltantes? Antes de regresar a la tienda, llama al Servicio al Cliente de Hampton Bay 8 a.m. – 7 p.m., Hora del Este, Lunes – Viernes 8 a.m. – 6 p.m., Hora del Este, Sábado 1-855-HD-HAMPTON HAMPTONBAY.COM Conserve este manual para futuras consultas.
Article: 1001398739 Modèle: HB2583-35 GUIDE D'UTILISATION ET D'ENTRETIEN ____________________________________ LUSTRE DE 5 LUMIÈRE Questions, problèmes, pièces manquantes? Avant de retourner au magasin, appeler Hampton Bay Service à la clientèle 8:00 – 19:00, HNE, Lundi – Vendredi 8:00 – 18:00, HNE, Samedi 1-855-HD-HAMPTON HAMPTONBAY.COM MERCI Nous apprécions la confiance que vous avez placée dans Hampton Bay grâce à l'achat de cette lustre.
Table des Matières Table des Matières Consignes de Sécurité Garantie Pré-Installation Planification du l’Installation Outils Matériel Contenu du Paquet 22 22 22 23 23 23 23 24 Installation Opération Entretien et Nettoyage Entretien Extérieur Entretien Intérieur Dépannage 25 29 29 29 29 29 Consignes de Sécurité Avant de commencer l'installation de ce luminaire ou à la dépose d'un précédent luminaire, débrancher l'alimentation en désactivant le disjoncteur ou en retirant le fusible de la platine de fus
Pré-Installation PLANIFICATION DE L'INSTALLATION Lire toutes les instructions avant assemblage et l'installation. Avant de commencer l'installation du luminaire ou la dépose d'un précédent luminaire, débrancher l'alimentation en désactivant le disjoncteur ou en retirant le fusible de la platine de fusibles. Pour éviter d'endommager le produit, assembler sur un doux et non abrasif surface tels que tapis ou un morceau de carton. NOTE: Conservez votre reçu et ces instructions à la preuve d'achat.
Pré-Installation (continue) CONTENU DU PAQUET A C D B Partie Description Quantité A Pavillon 1 B Corps du Luminaire 1 C Abat-jour en Verre 5 D Tige Centrale 1 24
Installation 1 Le montage du plaque de fixation Vissez les deux écrous hexagonaux (AA) sur la tige filetée (EE) jusqu’à ce qu’ils atteignent le milieu de la tige. Vissez la tige filetée (EE) dans le trou central de la plaque de fixation (JJ) jusqu’à ce qu’environ 1/3 de la tige soit inséré. Ne serrez pas les écrous hexagonaux (AA). Tirez les fils d’alimentation et le fil de terre de la boîte de sortie hors de la boîte de sortie.
Installation (continue) 3 Réglage de la longueur de la chaîne Maillon Ouvert Fileter la tige centrale (D) sur le couplage. Vissez l’anneau de suspension (II) sur le dessus du corps du luminaire (B). Fixer la chaîne (KK) de la boucle supérieure (II) en utilisant le lien de la chaîne de connecteur (DD). KK Soulevez la chaîne KK) et le corps du luminaire (B) jusqu’à la boîte de sortie pour mesurer la longueur de chaîne désirée pour l’installation.
Installation (continue) 5 Enfiler le câble Faites passer le cordon et le fil de terre du luminaire dans le trou central de l’anneau à collier fileté (HH), puis à travers la tige filetée (EE), et hors de la boîte de sortie. JJ FF HH Continuez à faire passer le cordon et le fil de terre jusqu’à ce que les deux soient bien tendus. Coupez l’excédent du cordon et du fil de terre pour ne laisser qu’environ 15,24 cm (6 po.) hors de la boîte de sortie.
Installation (continue) 7 Sécurisation le pavillon Faites glisser le pavillon (A) le long de la chaîne (KK), en direction de la boîte de sortie jusqu’à ce qu’il repose contre le plafond. Glissez l’anneau fileté (CC) le long de la chaîne (KK) et vissez-le sur le collier fileté de l’anneau (HH) pour fixer le pavillon (A) solidement contre le plafond. A CC HH KK 8 Assemblage de la lustre NOTE: La puissance de l’ampoule incandescente ne doit pas dépasser 60W.
Opération Mettez sous tension au niveau du disjoncteur ou des fusibles. Allumez l'interrupteur pour activer l'appareil. Entretien et Nettoyage ENTRETIEN EXTÉRIEUR NOTE: N’utilisez aucun produit de nettoyage contentant des agents chimiques, des solvants ou des abrasifs durs. Utilisez uniquement un linge doux et sec pour enlever la poussière en essuyant délicatement Utilisez un linge sec ou légèrement humide et essuyez le luminaire.
Questions, problèmes, pièces manquantes? Avant de retourner au magasin, appeler Hampton Bay Service à la clientèle 8:00 – 19:00, HNE, Lundi – Vendredi 8:00 – 18:00, HNE, Samedi 1-855-HD-HAMPTON HAMPTONBAY.COM Conserver ce manuel pour un utilisation ultérieure.