Item #1000248593 1000248617 Model #HBI-4192-BK-D HBI-4192-WH-D USE AND CARE GUIDE DECORATIVE MOTION LIGHT Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM THANK YOU We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this decorative motion light.
Table of Contents Hardware Included..................................4 Package Contents...................................4 Installation.................................................5 Wiring Options...........................................7 Operation...................................................8 Care and Cleaning...................................10 Troubleshooting.......................................10 Table of Contents.......................................2 Safety Information...............
Pre-Installation PLANNING INSTALLATION Before installing the light fixture, ensure that all parts are present. Compare parts with the Hardware Included and Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this light fixture. Estimated installation time: 30 minutes SPECIFICATIONS Range Up to 30 ft. (9.
Pre-Installation (continued) HARDWARE INCLUDED NOTE: Hardware shown to actual size.
Installation the mounting 1 Removing bracket □ □ FF DD CC Remove the two decorative fixture nuts (CC) from the light fixture (A). Remove the mounting bracket (FF) from the light fixture (A). A 2 Installing the mounting bracket WARNING: Turn the power off at the circuit breaker or fuse. Place tape over the circuit breaker switch and verify power is off at the light fixture. □ □ □ □ DD Remove the existing light fixture.
Installation (continued) 3 Wiring the light fixture □ Connect all ground wires to the pigtail wire (1) attached to the green ground screw. NOTE: This light fixture can be wired to control another standard or motion sensing light fixture(s). See Wiring Options for additional wiring methods. Black to black CAUTION: DO NOT remove wire connector from RED wire or connect the RED wire unless you want to control other lights from this motion sensor fixture.
Installation (continued) 5 Installing the light bulb □ □ □ EE B Install the bulb (tungsten incandescent, medium base, type “A”, 60 watt maximum not included) into the light fixture (A). Place the fixture cap (B) onto the light fixture (A). Secure the fixture cap (B) with the two decorative screws (EE).
Wiring Options (continued) a motion sensing 3 Controlling light fixture(s) White to white Black to black IMPORTANT: Total fixture ratings must not exceed 360 Watts (3.0 A). Primary Light Red to black When wiring to control another motion sensing light fixture (Primary / Controlled): □ □ □ Strip the red wire in both light fixtures. Connect the red wire of the controlling (primary) fixture (A) to the red and black wires of the controlled (controlled) fixture. Connect all white wires together.
Operation (continued) the motion sensor 2 Determining coverage area □ □ □ □ Perform a “walk test”: walk in an arc in front of the motion sensor (C). Watch the light (A). The light (A) will come on when motion has been detected. Stop, wait for the light (A) to turn off, and then begin walking again. Continue this process until the detection zone has been established. C 3 Adjusting the SENS control □ □ A To increase the detection zone, turn the “SENS” control toward the “+” position.
Operation (continued) 6 Using manual mode NOTE: If the power to the light fixture is off for more than 5 seconds, allow the motion sensor to warm up prior to switching to manual mode. NOTE: Manual mode overrides the motion sensor and “ON‑TIME” control so the light will operate full bright. This feature only works at night and only for one night at a time. The motion sensor will reset to motion sensing mode after 6 hours or sunrise, whichever comes first.
Troubleshooting (continued) Problem Possible Cause Solution The light comes on for no apparent reason. □ The motion sensor may be sensing small animals or automobile traffic. □ Decrease the “Sensitivity” setting. □ The “Sensitivity” setting is set too high. □ Decrease the “Sensitivity” setting. □ The “DUALBRITE” switch is in the 3 hour, 6 hour, or dusk-to-dawn setting. □ The light fixture is operating normally under these circumstances.
Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM Retain this manual for future use.
Articulo #1000248593 1000248617 Modelo #HBI-4192-BK-D HBI-4192-WH-D GUÍA PARA EL USO Y CUIDADO LUZ DECORATIVA DETECTORA DE MOVIMIENTO ¿Tiene preguntas, problemas o piezas faltantes? Antes de devolverlo a la tienda, llame a Servicio al Cliente de Defiant de 08 a.m.-7 p.m., EST, Lunes - Viernes, 09 a.m.-6 p.m., EST, sábado. 1-855-HD-HAMPTON HAMPTONBAY.COM GRACIAS Agradecemos la confianza que ha depositado en Hampton Bay al comprar esta luz decorativa detectora de movimiento.
Contenido Ferretería Incluida.................................16 Contenido del Paquete..........................16 Instalación...............................................17 Opciones de cableado.............................19 Operación.................................................20 Cuidado y limpieza..................................22 Análisis de averías..................................22 Contenido.................................................14 Información de seguridad.......................
Antes de la instalación PLANIFICACIÓN DE LA INSTALACIÓN Antes de instalar el aparato de luz, esté seguro que estén todas las piezas. Compare las piezas con la Ferretería incluida y las secciones de Contenidos del paquete. Si cualquier pieza falta o está dañada, no intente ensamblar, instalar ni operar este aparato de luz.
Antes de la instalación (continuación) FERRETERÍA INCLUIDA NOTA: La ferretería se muestra en su tamaño real AA BB CC DD Pieza EE Descripción FF Cantidad AA Tornillo del soporte de montaje 2 BB Capuchón para cable 3 CC Tuerca decorativa del aparato (pre-instalado) 2 DD Tornillo grande de montaje (pre-instalado) 2 EE Anillos decorativos 2 FF Soporte de montaje (pre-instalado, no está a escala) 1 CONTENIDO DEL PAQUETE B A C Pieza Descripción Cantidad A Tapa del aparato de luz
Instalación 1 Retiro del soporte de montaje □ □ FF DD CC Retire los dos tornillos decorativos (CC) de la lámpara (A). Retire el soporte de montaje (FF) de la lámpara (A). A del soporte de 2 Instalación montaje □ ADVERTENCIA: Desconecte la energía eléctrica en el disyuntor o en el fusible. Coloque cinta aislante sobre el interruptor disyuntor y compruebe que no haya energía eléctrica en el aparato de luz. □ □ □ Retire el aparato de luz existente.
Instalación (continuación) 3 Cableado del aparato de luz □ Conecte todos los cables de tierra al cable flexible (1) sujetado al tornillo verde de tierra. NOTA: Este aparato puede cablearse para controlar otro(s) aparato(s) de luz estándar o detectores de movimiento. Ver Opciones de cableado para métodos adicionales de cableado.
Instalación (continuación) 5 Instalación de la bombilla □ □ □ EE B Instale la bombilla (incandescente de tungsteno, de base mediana, de tipo “A”, de 60 vatios máximo - no incluida) en la lámpara (A). Coloque el sombrerete del aparato (B) sobre la lámpara (A). Asegure el sombrerete del aparato (B) con los dos tornillos decorativos (EE).
Opciones de cableado (continuación) controlar una(s) 3 Cómo lámpara(s) detectora(s) de □ Conecte todos los cables de tierra juntos. Blanco a Blanco movimiento IMPORTANTE: La capacidad total no debe exceder los 360 Vatios (3,0 A). Negro a Negro Luz primaria Cuando prepare una conexión para controlar otro aparato de luz detector de movimiento (Primaria / Controlada): □ □ Rojo a Negro Pele el alambre rojo en ambos aparatos de luz.
Operación (continuación) de la área de 2 Determinación cobertura del detector de □ Continúe este proceso hasta que la zona de detección haya sido establecida. movimiento □ □ □ Haga una “prueba caminando”: camine formando un arco frente al detector de movimiento (C). Observe la luz (A). La luz (A) se encenderá cuando detecte movimiento. Deténgase, espere que la luz (A) se apague, y luego empiece a caminar de nuevo.
Operación (continuación) 6 Uso del la fase manual NOTA: Si la energía eléctrica al aparato de luz es apagada por más de 5 segundos, deje que el detector de movimiento se caliente antes del cambio a la fase manual. NOTA: La fase manual anula el detector de movimiento y el control de duración (“ON-TIME”), de esta forma la lámpara operará con todo su brillo. Esta característica funciona solamente en la noche y solamente una noche a la vez.
Análisis de averías (continuación) Problema Causa Probable Solución La luz se enciende sin razón aparente. □ El detector de movimiento puede estar detectando pequeños animales o tráfico automotor. □ Reduzca el ajuste de sensibilidad (“SENS”). □ El ajuste “Sensibilidad” es demasiado alto. □ Reduzca el ajuste de sensibilidad (“SENS”). □ El interruptor “DUALBRITE” está en la calibración 3 horas, 6 horas, o del crepúsculo al amanecer.
¿Tiene preguntas, problemas o piezas faltantes? Antes de devolverlo a la tienda, llame a Servicio al Cliente de Defiant de 08 a.m.-7 p.m., EST, Lunes - Viernes, 09 a.m.-6 p.m., EST, sábado. 1-855-HD-HAMPTON HAMPTONBAY.COM Guarde este manual para uso futuro.