Item #882731 Model #HD10 USE AND CARE GUIDE 38,200 BTU BRONZE HEAT-FOCUSING PROPANE GAS PATIO HEATER Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM THANK YOU We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this patio heater. We strive to continually create quality products designed to enhance your home.
Table of Contents Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pre-Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Planning Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Tools Required. . . . . . . . . . . . .
Safety Information (continued) WARNING: ONLY use this appliance on a flat LEVEL non flammable surface or ground. WARNING: In the event of an uncontrollable fire, immediately disconnect the gas cylinder moving it away from fire and contact the fire services. DO NOT PUT YOURSELF AT RISK! WARNING: When positioning, ensure the unit is a minimum of 40 in. (1 m) from flammable items or structure from all sides and above. WARNING: Ensure aerosols are not used near this unit when in use.
Warranty 1 YEAR LIMITED WARRANTY WHAT IS COVERED We warrant to the original consumer purchaser that all aspects of this product will be free of defects in material and workmanship for 1 year from the date of purchase. A replacement for any defective part will be supplied free of charge for installation by the consumer. This warranty shall be effective from the date of purchase as shown in the purchaser’s receipt.
Pre-Assembly PLANNING ASSEMBLY Before You Start, check the contents of the box and make sure you have all the parts and fittings listed. If not, contact Hampton Bay Customer Service at 1-855-HD-HAMPTON. When you are ready to start, make sure that you have the right tools at hand, plenty of space and a clean dry area for assembly. WARNING: While every precaution has been made in the manufacture of this product, care must be taken during assembly in case sharp edges are present.
Pre-Assembly (continued) PACKAGE CONTENTS K L H J G B C I F E D A Part A B C D E F Description Base Cylinder Chamber Supports (A, B, C) Lower Support Pole Cylinder Chamber Wall Cylinder Chamber Door Cylinder Chamber Top Part G H I J K L Quantity 1 3 1 1 1 1 6 Description Upper Support Pole Lantern And Hose Regulator Reflector Handle Top Panel Side Panels Quantity 1 1 1 1 1 6
Pre-Assembly (continued) TECHNICAL DATA Overall Height Overall Weight Overall Width Heater Heat Input (·Qn) Heater Gas Consumption Heater Injector Size Setting Pressure Regulator Outlet Pressure Standard Gas Supply Pressure 95 in. approx. 82.6 lbs 34 in. 38,200 Btu/h 1.77 Lbs per hour 0.0744 in. 11.0 in. per W.C 11.0 in. per W.C ANSI Z83.26-2014 Gas Fired Outdoor infrared Patio heaters Max. 250 PSI, MIN.5 PSI 7 HAMPTONBAY.COM Please contact 1-855-HD-HAMPTON for further assistance.
Assembly 2 Attaching the lower support pole 1 Assembling the legs □□ Attach the lower support pole (C) to the cylinder chamber supports (B) using six bolts (CC) and nuts (BB). □□ Attach the cylinder chamber supports (B) to the corresponding section on the base (A) with six of the bolts (CC). □□ Finger tighten only at this stage. □□ Finger tighten only at this stage.
Assembly (continued) 3 Attaching the cylinder chamber wall 4 Attaching the cylinder chamber door □□ Hang the cylinder chamber door (E) on the hinges. □□ Using six of the bolts (AA) and nuts (BB), attach the cylinder chamber wall (D) to the cylinder chamber supports (B). □□ Ensure that the alignment is correct and tighten all bolts securely. □□ Finger tighten only at this stage. BB AA E B D 9 HAMPTONBAY.COM Please contact 1-855-HD-HAMPTON for further assistance.
Assembly (continued) 5 Attaching the cylinder chamber top 6 Attaching the upper support pole □□ Attach the upper support pole (G) to the lower support pole (C) using three bolts (CC), three washers (DD) and three spring washers (GG). □□ Slide the cylinder chamber top (F) down over the lower support pole (C) as shown and secure to the cylinder chamber supports (B), using three bolts (AA) and three nuts (BB).
Assembly (continued) 7 Attaching the lantern 8 bottle Attaching the regulator and propane □□ Feed the hose down through the support pole (G) and secure the lantern (H) to the support pole (G) using four bolts (CC), washers (DD) and spring washers (GG). NOTE: THE CYLINDER MUST BE POSITIONED AS SHOWN IN THE PATIO HEATER CYLINDER CHAMBER TO PROVIDE VAPOR WITHDRAWAL. □□ Connect the lantern and hose (H) to the regulator (I) and secure tightly with the adjustable wrenches.
Assembly (continued) 9 Fitting the reflector handle 10 Assembling the reflector WARNING: While every precaution has been made in the manufacture of this product, care must be taken during assembly in case sharp edges are present. □□ Using the pre-fitted R-clip (1) and pin (2), secure the reflector handle (J) to the bracket as shown. □□ Loosely screw the side panels (L) together using twelve bolts (AA) and nuts (BB), overlapping as shown below.
Assembly (continued) 11 lantern Attaching the reflector to the 12 Fitting the battery □□ Unscrew sparker button (1) and insert battery (2), positive side facing outwards. □□ Fit the reflector to the lantern (H) using three bolts (FF) and washers (EE). FF EE 1 2 H 13 HAMPTONBAY.COM Please contact 1-855-HD-HAMPTON for further assistance.
Operation □□ The heater, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1. □□ Certain materials or items, when stored under the heater, will be subjected to radiant heat and could be seriously damaged. □□ Inspect the visible portion of the hose before each use of the appliance.
Operation (continued) □□ Important - Make sure the gas bottle is placed level within the base. □□ Should you need to change the gas bottle, confirm the gas supply is turned off at the regulator or bottle / cylinder valve, and there are no sources of ignition (cigarettes, open flame, sparks, etc.) near before proceeding. □□ Inspect the gas hose to ensure it is free from any twisting or tension. The hose should hang freely with no bends, folds, or kinks that could obstruct free flow of gas.
Operation (continued) LEAK TESTING Your patio heater has been checked at all factory connections for leakage. To check the connection at the gas hose/regulator/cylinder: □□ Ensure you are in a well ventilated area. □□ Confirm all control knobs are in the off position. □□ Open the gas control valve on the bottle. □□ Check for leaks by brushing a solution of 50% water and 50% dish soap over the gas system joints, including all valve connections, hose connections and regulator connections.
Maintenance FLAME CHARACTERISTIC □□ The flame pattern at the burner mesh should be visually checked whenever the heater is operated. □□ Normally, the burner flame is blue with yellow flame at the top. The burner mesh will become red hot. □□ If flames extend beyond the surface of the burner mesh, or there is the phenomena of flame lift or light back, or a black spot is accumulating on the burner mesh or reflector, the heater should be turned off immediately.
Page intentionally left blank.
Page intentionally left blank.
Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM Retain this manual for future use.
