Installation Guide

Item #1001 492 055
Model #HD28682
Use and Care Guide
LOW VOLTAGE HALF BRICK STEP LIGHT
Part Description Quantity
A
Face plates
2
B
Thumbscrews
2
C
7W Incandescent Wedge Bulb
1
D
Wire
1
E
Connector
1
F
Screws
4
PACKAGE CONTENTS
Assembly and Installation
1
Attaching and installing the light
2
Connecting the wires
NOTE: The wiring access hole on the back of the xture has been sized to allow for a
1/2 inch conduit connection provision once the exible grommet has been removed.
WARNING: The wire connector (E) contacts have sharp edges for piercing the
main low voltage cable. To avoid injury, do not touch the metal contacts.
CAUTION: The wire from the low voltage power unit shall be 12-16 AWG type
underground low Energy Circuit Cable or SPT2W.
CAUTION: Safe for outdoor operation
WARNING: To reduce the risk of FIRE OR INJURY TO PERSONS:
WARNING: Turn off/unplug and allow to cool before replacing lamp.
WARNING: Lamp gets HOT quickly! Contact only switch/plug when turning on.
Do not touch hot lens, guard or enclosure.
WARNING: Keep the lamp away from materials that may burn.
WARNING: Do not touch the lamp at any time. Use a soft cloth. Oil from skin may
damage the lamp.
IMPORTANT:
• Protect the wiring by routing it in close proximity to the light tting, or next to a
building structure such as a house or deck.
• The landscape wire and connector can also be hidden under stone or buried
under grass at a maximum depth of 6” (15.24 cm).
• Do not submerge xture in water.
□ WITH LOUVER PLATE
□ Cut a 2-3/8 in. x 3-3/4 in. opening in the mounting surface.
□ Secure the xture onto the surface using the four screws (F)
included.
□ Insert the bulb (C) into the bulb socket.
□ Install the louver plate with the two (2) provided thumbscrews (B).
□ Make sure the O-ring stays on the thumbscrews (B).
□ WITH DIFFUSER PLATE
□ Cut a 2-3/8 in. x 3-3/4 in. opening in the mounting surface.
□ Secure the xture onto the surface using the four screws (F)
included.
□ Insert the bulb (C) into the bulb socket.
□ Install the diffuser place with the two thumbscrews (B).
□ Make sure the O-ring stays on the thumbscrews (B).
WARNING: Risk of Electric Shock. Install all luminaires 10 ft. (3.05 m) or more
from a pool, spa or fountain.
WARNING: Install in accordance with all local codes and ordinances.
□ Place the wire connector (E) on opposite sides of the low
voltage cable (not included) where the xture will be located.
□ Align and t the main low voltage cable vertically to the slot of
the wire connector (E) as shown.
□ Press the wire connector (E) together until fully seated and
locked around the cable. Pre-set prongs will pierce the cable
insulation and establish contact. Turn on the power unit. If the
light xture does not turn on, repeat the previous steps.
□ Once the clip-on connector (E) is in place, wrap it with
electrical tape for additional protection.
□ CAUTION BE CAREFUL! THE WIRE STABS ARE VERY SHARP!
□ After all xtures are installed, turn on the transformer.
E
Only for use with low voltage power units with a maximum output rating of 15V,
300W per secondary.
FOR LANDSCAPE LIGHTING SYSTEMS ONLY. OUTDOOR USE ONLY. THE DEVICE IS
ACCEPTED AS A COMPONENT OF A LANDSCAPE LIGHTING SYSTEM WHERE THE
SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR LOCAL
INSPECTION AUTHORITIES HAVING JURISDICTIO
N.
UL LISTED UNDER MODEL # U201138
Please read and save these instructions
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS
Lighted lamp is HOT!
A
B
F
D
C
E
1
3/4
” (4.5 cm)
2
3/8
2
3/8
3
3/4
3
3/4
Bulb (C)
Diffuser plate
Louver plate
1
3/4
” (4.5 cm)
2
3/8
2
3/8
3
3/4
3
3/4
Wire (D)
Connector (E)
1
3/4
” (4.5 cm)
2
3/8
2
3/8
3
3/4
3
3/4
Screw (F)
1
3/4
” (4.5 cm)
2
3/8
2
3/8
3
3/4
3
3/4
O-Ring
Thumbscrew (B)