Instructions / Assembly
Item #1001 492 705
Model #HD28906
Use and Care Guide
LOW VOLTAGE PATHLIGHT AND FLOODLIGHT KIT
Part Description Quantity
A
Lens cover
2
B
Lens
2
C
20W Halogen MR11 Bulb
2
D
Body
2
E
Adjustment screw
2
F
Post
2
G
Connector
2
H
Spike
2
I
Top Cover
6
J
10W Halogen T3 Bulb
6
K
Bulb socket
6
L
Post
6
M
Connector
6
N
Spike
6
O
120W Transformer
1
P
Wire AWG14 SPT2W 75’
1
Q
Plastic anchor
1
R
Screw
1
PACKAGE CONTENTS
Assembly and Installation
1
Attaching and installing the oodlight
2
Attaching and installing the pathlight
WARNING: Never push the xture into the ground by the lamp body (D) or use a
hammer to insert the spike (H) into the ground.
WARNING: Never push the xture into the ground by the lamp body (L) or use a
hammer to insert the spike (N) into the ground.
CAUTION: Safe for outdoor operation
WARNING: To reduce the risk of FIRE OR INJURY TO PERSONS:
WARNING: Turn off/unplug and allow to cool before replacing lamp.
WARNING: Lamp gets HOT quickly! Contact only switch/plug when turning on.
Do not touch hot lens, guard or enclosure.
WARNING: Keep the lamp away from materials that may burn.
WARNING: Do not touch the lamp at any time. Use a soft cloth. Oil from skin may
damage the lamp.
WARNING: Do not operate the luminaire tting with a missing or damaged lens
or bulb protector.
□ Carefully remove the xture from its protective packaging.
□ Run the wire through the notch in the top of the spike (H) and attach
the spike to the post (F) by turning clockwise.
□ Loosen the set screw (1) and slide off the light cap (A).
□ Remove the lens cover (B) by turning counterclockwise.
□ Do not remove the lens from the lens cover.
□ Insert the bulb (C) into the bulb socket.
Use a soft cloth, as oil from skin may
damage the lamp bulb.
□ Replace the lens cover (B) and the light cap
(A) over the body (D). Adjust the light’s beam
by sliding the cap back and forth (back = wide
beam, front = narrow beam) and screw the set
screw (1) in place once the proper light beam
is found.
□ Adjust the xture’s angle by loosening the
adjustment screw (E) and retightening it.
□ Ensure the lens points up and never towards
the ground.
□ Carefully remove the xture from its protective packaging.
□ Pass the wire through the notch in the top of the spike (N) and
attach the spike and post (L) by pressing them together.
□ Insert the bulb (J) into the bulb socket (K). Use a soft cloth, as oil
from skin may damage the lamp bulb.
□ Attach the cover (I) and the post (L) together by turning clockwise.
WARNING: Install in accordance with all local codes and ordinances.
Only for use with low voltage power units with a maximum output rating of 15V,
300W per secondary.
FOR LANDSCAPE LIGHTING SYSTEMS ONLY. OUTDOOR USE ONLY. THE DEVICE IS
ACCEPTED AS A COMPONENT OF A LANDSCAPE LIGHTING SYSTEM WHERE THE
SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR LOCAL
INSPECTION AUTHORITIES HAVING JURISDICTIO
N.
PATHLIGHT UL LISTED UNDER MODEL # U201159
SPOTLIGHT UL LISTED UNDER MODEL # U201167
Please read and save these instructions
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS
Lighted lamp is HOT!
O
P
Q
R
3
Connecting the wires
WARNING: The wire connector (G) & (M) contacts have sharp edges for piercing
the main low voltage cable. To avoid injury, do not touch the metal contacts.
CAUTION: The wire from the low voltage power unit shall be 12-16 AWG type
underground low Energy Circuit Cable or SPT2W.
IMPORTANT:
• Protect the wiring by routing it in close proximity to the light tting, or next to a
building structure such as a house or deck.
• The landscape wire and connector can also be hidden under stone or buried
under grass at a maximum depth of 6” (15.24 cm).
• Do not submerge xture in water.
WARNING: Risk of Electric Shock. Install all luminaires 10 ft. (3.05 m) or more
from a pool, spa or fountain.
A
B
C
D
F
E
G
H
I
J
K
L
N
M
A
B
1
C
D
F
E
H
G R E
A
S
E
!
I
J
K
L
N
M
IMPORTANT: Apply petroleum grease around the post threading when replacing the
head after you change the light bulb. Do not overtighten the head onto the post.