Installation Guide

Item #1001 492 715
Model #HD28928
Use and Care Guide
LOW VOLTAGE FLOODLIGHT KIT
Part Description Quantity
A
Lens cover
4
B
20W Halogen T3 Bi-Pin Bulb
4
C
Body
4
D
Adjustment screw
4
E
Connector
4
F
Spike
4
G
120W Transformer
1
H
Wire AWG16 SPT2W 50’
1
I
Plastic anchor
1
J
Screw
1
PACKAGE CONTENTS
Assembly and Installation
1
Attaching and installing the oodlight
WARNING: Never push the xture into the ground by the lamp body (C) or use a
hammer to insert the spike (F) into the ground.
CAUTION: Safe for outdoor operation
WARNING: To reduce the risk of FIRE OR INJURY TO PERSONS:
WARNING: Turn off/unplug and allow to cool before replacing lamp.
WARNING: Lamp gets HOT quickly! Contact only switch/plug when turning on.
Do not touch hot lens, guard or enclosure.
WARNING: Keep the lamp away from materials that may burn.
WARNING: Do not touch the lamp at any time. Use a soft cloth. Oil from skin may
damage the lamp.
WARNING: Do not operate the luminaire tting with a missing or damaged lens
or bulb protector.
□ Carefully remove the xture from its protective packaging.
□ Remove the lens cover (A) by turning counterclockwise.
□ Do not remove the lens from the lens cover.
□ Insert the bulb (B) into the bulb socket. Use a soft cloth, as oil from
skin may damage the lamp bulb.
□ Replace the lens cover (A) on the body (C) by turning clockwise.
□ Adjust the xture’s angle by loosening the adjustment screw (D)
and retightening it.
□ Ensure the lens points up and
never towards the ground.
WARNING: Install in accordance with all local codes and ordinances.
Only for use with low voltage power units with a maximum output rating of 15V,
300W per secondary.
FOR LANDSCAPE LIGHTING SYSTEMS ONLY. OUTDOOR USE ONLY. THE DEVICE IS
ACCEPTED AS A COMPONENT OF A LANDSCAPE LIGHTING SYSTEM WHERE THE
SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR LOCAL
INSPECTION AUTHORITIES HAVING JURISDICTIO
N.
UL LISTED UNDER MODEL # U201166
Please read and save these instructions
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS
Lighted lamp is HOT!
G
H
I
J
2
Connecting the wires
WARNING: The wire connector (E) contacts have sharp edges for piercing the
main low voltage cable. To avoid injury, do not touch the metal contacts.
CAUTION: The wire from the low voltage power unit shall be 12-16 AWG type
underground low Energy Circuit Cable or SPT2W.
IMPORTANT:
• Protect the wiring by routing it in close proximity to the light tting, or next to a
building structure such as a house or deck.
• The landscape wire and connector can also be hidden under stone or buried
under grass at a maximum depth of 6” (15.24 cm).
• Do not submerge xture in water.
WARNING: Risk of Electric Shock. Install all luminaires 10 ft. (3.05 m) or more
from a pool, spa or fountain.
A
B
C
D
F
E
A
B
C
D
□ Place the wire connector (E) on opposite sides of the low
voltage cable (H) where the xture will be located.
□ Align and t the main low voltage cable (H) vertically to the
slot of wire connector (E) as shown.
□ Press the wire connector (E) together until fully seated and
locked around the cable (H). Pre-set prongs will pierce the
cable insulation and establish contact. Turn on the power unit.
If the light xture does not turn on, repeat previous steps.
□ Once the clip-on connector (E) is in place, wrap it with
electrical tape for additional protection.
□ CAUTION BE CAREFUL! THE WIRE STABS ARE VERY SHARP!
□ After all xtures are installed, turn on the transformer.
E