Installation Guide

ManualsBrandsHampton Bay ManualsLandscape LightingLow Voltage Black Outdoor Integrated LED Landscape Path Light (6-Pack Kit)

Item #1002 753 136

Model #HD33678

Use and Care Guide

LOW VOLTAGE PATHLIGHT KIT

Part Description Quantity

Caps

Lens

Posts

Spikes

Connectors

24W transformer

Cable

Control Box

PACKAGE CONTENTS

Assembly and Installation

Attaching and installing the pathlight

WARNING: Never push the xture into the ground by the head or use a hammer

to insert the spike (D) into the ground.

CAUTION: Safe for outdoor operation.

WARNING: To reduce the risk of FIRE OR INJURY TO PERSONS:

WARNING: Do not operate the luminaire tting with a missing or damaged lens

or bulb protector.

□ Carefully remove the xture from its protective packaging.

□ Install the four (4) glass lenses (B) in the lantern body and

attach to the post (C) and insert the spike (D) into the post (C).

□ Attach top cover (A) to the body by pushing the cover gently on

the top of the body.

WARNING: Install in accordance with all local codes and ordinances.

Only for use with low voltage power units with a maximum output rating of 15V,

300W per secondary.

FOR LANDSCAPE LIGHTING SYSTEMS ONLY. OUTDOOR USE ONLY. THE DEVICE IS

ACCEPTED AS A COMPONENT OF A LANDSCAPE LIGHTING SYSTEM WHERE THE

SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR LOCAL

INSPECTION AUTHORITIES HAVING JURISDICTIO

PATHLIGHT ETL LISTED UNDER MODEL # U000-1999

Please read and save these instructions

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS

IMPORTANT SAFETY INSTRUCTIONS

Lighted lamp is HOT!

Connecting the wires

WARNING: The wire connector (E) contacts have sharp edges for piercing the

main low voltage cable. To avoid injury, do not touch the metal contacts.

CAUTION: The wire from the low voltage power unit shall be 12-18 AWG type

underground low Energy Circuit Cable or SPT2W.

IMPORTANT:

• Protect the wiring by routing it in close proximity to the light tting, or next to a

building structure such as a house or deck.

• The landscape wire and connector can also be hidden under stone or buried

under grass at a maximum depth of 6 in. (15.24 cm).

• Do not submerge the xture in water.

WARNING: Risk of Electric Shock. Install all luminaires 10 ft. (3.05 m) or more

from a pool, spa or fountain.

WARNING: To reduce the risk of FIRE OR INJURY TO PERSONS:

WARNING: There are no serviceable parts inside the power supply unit. DO NOT

DISASSEMBLE.

WARNING: Do not submerge the transformer.

WARNING: Do not connect two or more transformers in parallel.

WARNING:

For use with 12 volt low voltage outdoor landscape lighting system only.

Not for use with submersible light or pool/spa equipment.

WARNING: Do not use with a dimmer.

CAUTION: Plug the power supply unit directly into a GFCI outlet that is marked “wet

location”. The maximum output of this transformer is 24 watts. Do not overload

the

transformer. Be sure that the total cumulative wattage of all 12 volt xtures connected

to the transformer is equal to or less than 24 watts. This garden light system must be

installed in accordance with all local codes and ordinances. If you are experiencing

problems, contact a qualied electrician.

WARNING: Do not use an extension cord.

Body

Summary of content (9 pages)

PAGE 1
Item #1002 753 136 Model #HD33678 Use and Care Guide Please read and save these instructions LOW VOLTAGE PATHLIGHT KIT PACKAGE CONTENTS Part A A F B B C D C E E G F G H H D Description Quantity Caps Lens Posts Spikes Connectors 24W transformer Cable Control Box 6 24 6 6 6 1 1 1 Assembly and Installation INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS IMPORTANT SAFETY INSTRUCTIONS Lighted lamp is HOT! 1 Attaching and installing the pathlight WARNING: Never push the fixt
PAGE 2
Assembly and Installation (Continued) □□ Place the wire connector (E) on opposite sides of the low voltage cable (G) where the fixture will be located. □□ Align and fit the main low voltage cable (G) vertically to the slot of wire connector (E) as shown. □□ Press the wire connector (E) together until fully seated and locked around the cable (G). Pre-set prongs will pierce the cable insulation and establish contact. Turn on the power unit. If the light fixture does not turn on, repeat previous steps.
PAGE 3
Care and Cleaning □□ Clean the fixture with a soft, dry cloth. □□ Do not use any cleaners with chemicals, solvents or harsh abrasives. Troubleshooting Problem Possible cause The fixture will not light. Only some lights work. Solution • There is no power. • There is a disconnection or break in the wire. • There is a light source near the transformer. • There are too many fixtures connected to the transformer. • Check that the power is on.
PAGE 4
Item #1002 753 136 Modèle #HD33678 Guide d’utilisation et d’entretien Veuillez lire et conserver ces instructions ENSEMBLE DE LANTERNES À DEL DE BASSE TENSION CONTENU DE L’EMBALLAGE Pièce A F B B C D C E E G F G H H D Description Quantité Couvercles Vitres Poteaux Piquets Connecteurs Transformateur de 24W Câble Boîtier de contrôle A 6 24 6 6 6 1 1 1 Assemblage et installation INSTRUCTIONS PERTINENTES CONCERNANT LES CAUSES DE BRÛLURES OU DE BLESSURES.
PAGE 5
Assemblage et installation (continué) □□ Placer le connecteur du câble (E) sur les côtés opposés du câble basse tension (G) où sera situé le luminaire. □□ Aligner et placer le câble principal basse tension (G) verticalement à la fente du connecteur de fil (E) comme indiqué. □□ Appuyez sur le connecteur du câble (E) jusqu’à ce qu’il soit bien en place et verrouillé autour du câble. Les dents perceront l’isolation du câble et établiront le contact. Allumez l’unité de puissance.
PAGE 6
Soin et entretien □□ Nettoyez l’appareil avec un chiffon doux et sec. □□ Ne pas utiliser de produits de nettoyage avec des produits chimiques, de solvants ou de produits abrasifs. Dépannage Problème Cause probable Solution Le luminaire ne s’allume pas. • Il n’y a pas de puissance. • Il y’a une déconnexion ou une rupture dans le fil. • Vérifiez que l’appareil est sous tension. • Vérifier que toutes les connexions sont bien serrées aux bornes du transformateur. Seulement quelques luminaires s’allument.
PAGE 7
Núm. de artículo 1002 753 136 Núm.
PAGE 8
Ensamblaje e instalación (continuación) □□ Coloque el conector del cable (E) en los lados opuestos del cable de bajo voltaje (G) donde estará localizada la luminaria. □□ Alinee y ajuste el cable de bajo voltaje principal (G) de manera vertical a la ranura del conector del cable (E) como se muestra. □□ Presione el conector del cable (E) hasta que asiente completamente y se bloquee alrededor del cable (G). Las clavijas preinstaladas perforarán el aislamiento del cable y establecerán contacto.
PAGE 9
Cuidado y limpieza □□ Limpie la lámpara con un paño suave y seco. □□ No use ningún limpiador con químicos, solventes o abrasivos ásperos. Resolución de fallas Problema Posible causa El dispositivo no enciende. Solo algunas luces funcionan. Solución • No hay suministro de energía. • Hay una desconexión o ruptura en el cable. • Hay una fuente de luz cercana al transformador. • Hay demasiados dispositivos conectados al transformador. • Verifique que la energía esté encendida.