Instructions / Assembly

ManualsBrandsHampton Bay ManualsLandscape Lighting10-Watt Black Outdoor Integrated LED Landscape Path Light

Use and Care Guide

LED LOW VOLTAGE

SURFACE MOUNT LIGHT

PACKAGE CONTENTS

A – Fixture x1 C – Wire Connector (with 36 in. wire) x1 AA – Self-Threading BB – Plastic Anchor CC – Cardboard

B – Female Plug (with 12 in. wire) x1 D – Male Plug x1 Screw (30 mm) x2 (25 mm) x2 Template x1

ssembl

and Installation

Installing the

ixture with the wire routed behind the

mounting surface

Installing the

ixture with the wire in front of

the mounting surface

NOTE: This document provides two different methods for routing

the lead wire. You can chose which method best fits your needs.

□

Place the cardboard template (CC) on the mounting surface and mark

where the holes should be for the female plug (B) and the self-

threading screws (AA).

□

Use at least a 7/16 in. drill bit to drill a hole on the surface large

enough for the female plug (B) to pass through the hole on the

mounting surface.

□

Insert the female plug (B) through the hole on the mounting surface.

□

Insert the male plug (D) into the female plug (B).

□

Place the fixture (A) against the mounting surface.

□

Use a Phillips screwdriver to screw the self-threading screws (AA)

through the two holes on the fixture (A) to secure the fixture (A) to the

mounting surface.

□

Place the cardboard template (CC) on the mounting surface and

mark where the holes should be for the self-threading screws

(AA).

□

Insert the male plug (D) into the female plug (B).

□

The wire plugs may be retained inside the back of the fixture (A)

by coiling the wire and plugs and dropping the wire through the

notch in the bottom of the fixture (A).

□

The wire plugs may be left outside the fixture (A) by dropping the

wire through the notch in the bottom of the fixture (A) with the

plugs outside the back plate when the fixture is mounted. The

connected plugs are waterproof.

□

Place the fixture (A) against the mounting surface.

□

Use a Phillips screwdriver to screw the self-threading screws

(AA) through the two holes on the fixture (A) to secure the fixture

(A) to the mounting surface.

Item #1002 669 587

Model #JAO2601LM-2

Summary of content (7 pages)

PAGE 1
Item #1002 669 587 Model #JAO2601LM-2 Use and Care Guide LED LOW VOLTAGE SURFACE MOUNT LIGHT PACKAGE CONTENTS A D B AA C A – Fixture x1 C – Wire Connector (with 36 in. wire) x1 B – Female Plug (with 12 in.
PAGE 2
Assembly and Installation (continued) 2 Installing the fixture on a surface using plastic anchors □ □ □ □ If installation requires the plastic anchors (BB), then place the cardboard template (CC) on the mounting surface and mark where the holes should be for the self-threading screws (AA). At those marks, use a 15/64 drill bit (or 6 mm) to drill two holes in the mounting surface.
PAGE 3
Care and Cleaning □ Clean the fixture with a soft dry cloth. □ Do not use any cleaners with chemicals, solvents or harsh abrasives. Troubleshooting Problem Possible Cause Solution The fixture will not light. □ □ There is no power. There is a disconnection or break in the wire. The transformer setting is incorrect. □ Check the outlet and ensure that a breaker or GFCI circuit has not been tripped.
PAGE 4
Artículo #1002 669 587 Modelo #JAO2601LM-2 GUÍA DE USO Y MANTENIMIENTO REFLECTOR LED DE BAJO VOLTAJE PARA MONTAJE EN SUPERFICIE CONTENIDO DEL PAQUETE A D C B A –Dispositivo de Iluminación x1 B –Enchufe Hembra (con un cable de 12 pulgadas) x1 BB AA CC C –Conector Cable (con un cable de 36 pulgadas) x1 AA– Tornillos BB – Anclas de CC – Plantilla de D – Enchufe Macho x1 Autorroscantes (30mm) x2 Plastico (25mm) x2 Cartón x1 Montaje e Instalación 1 □ □ □ □ □ □ Instalando el dispositivo de iluminaci
PAGE 5
Montaje e Instalación (continuación) Instale el dispositivo de iluminación en una superficie con anclajes de plástico □ □ □ □ 2 Si la instalación requiere de anclajes de plástico (BB), coloque la plantilla de cartón (CC) en la superficie de montaje y marque los orificios para los tornillos de autorroscantes (AA). En esas marcas, use una broca de 15/64 (o 6 mm) para perforar dos orificios en la superficie de montaje.
PAGE 6
Mantenimiento y Limpieza □ Limpia la lámpara con un paño suave y seco. □ No uses limpiadores con químicos, solvents, o productos abrasivos. Solución de Problemas Problema Causa Posible Solución El accesorio no enciende. □ □ □ Verifique el tomacorriente y asegúrese que no esté apagado el interruptor o circuito □ La luz parpadea (en un accesorio). □ Las luzes parpadea (todos los accesorios). □ No hay corriente. El cable está desconectado o roto. El transformador está mal configurado.
PAGE 7
FCC Warning Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.