Instructions / Assembly

ManualsBrandsHampton Bay ManualsDeck LightingLow Voltage Black LED Deck Light

PACKAGE CONTENTS

A – Deck Light x 1 C– Hardscape Adaptor x 1 D – Wire Connector (with 12 in. wire) x 1 AA – Self-Threading BB – Plastic Anchor

B – Male Plug x 1 (with 36 in. wire) E – Female Plug x 1 Screw (30 mm) x 2 (25 mm) x 2

Preparing for installation

Installing a single deck light (without the hardscape

adaptor) on a wood surface

□ Out of the box, the male plug (B) is routed through the side of the deck light

(A). To use the male plug (B) this way, skip this Step 1. To use the male plug

(B) through the front or rear of the deck light (A), do the following:

□ Use a Philips screwdriver (sold separately) to unscrew the screw connecting

the foot base (1) at the end of the deck light (A) where the male plug (B) is

located.

□ Twist off the foot base (1) from the deck light (A).

□ Depending on your installation, route the male plug (B) through the rear or

the front groove of the foot base (1).

□ After routing the male plug (B), twist the foot base (1) back onto the deck

light (A). Use a Philips screwdriver to reconnect the screw at the foot base

(1) to the deck light (A).

NOTE: The deck light (A) comes pre-attached to the hardscape adaptor (C).

To use the deck light (A) without the hardscape adapter (C), use a Philips

screwdriver to unscrew the 2 screws connecting the hardscape adaptor (C)

to the deck light (A).

NOTE: Light projection can be adjusted by twisting the deck light (A) up or

down 90 degrees.

Deck light with wire behind the mounting surface:

□ Use at least a 7/16 in. drill bit to drill a hole on the mounting

surface large enough for the male plug (B) to pass through the hole

on the mounting surface.

□ Insert the male plug (B) through the hole on the mounting surface.

□ Place the deck light (A) against the mounting surface.

□ Use a Phillips screwdriver to screw the self-threading screws (AA)

through the two holes on the deck light (A) to secure the deck light (A)

to the mounting surface.

□ Insert the male plug (B) into the female plug (E).

□ Proceed to Step 6 if installing multiple lights, or Step 8.

Deck light with wire in front of or beside the mounting surface:

□ Place the deck light (A) on the surface where you want it to be

installed.

□ Use a Phillips screwdriver to screw the self-threading screws (AA)

through the two holes on the deck light (A) to the mounting surface.

□ Insert the male plug (B) into the female plug (E).

□ Proceed to Step 6 if installing multiple lights, or Step 8.

Summary of content (5 pages)

PAGE 1
PACKAGE CONTENTS A – Deck Light x 1 C– Hardscape Adaptor x 1 B – Male Plug x 1 (with 36 in. wire) D – Wire Connector (with 12 in. wire) x 1 E – Female Plug x 1 Deck light with wire behind the mounting surface: □ Use at least a 7/16 in. drill bit to drill a hole on the mounting surface large enough for the male plug (B) to pass through the hole on the mounting surface. □ Insert the male plug (B) through the hole on the mounting surface. □ Place the deck light (A) against the mounting surface.
PAGE 2
3 Installing a single deck light (with or without the hardscape adaptor) on concrete, brick, or other non-wood surface 4 Deck light with hardscape adaptor: □ Place the hardscape adaptor (C) on the surface where you want it to be installed, and choose which two holes on the hardscape adaptor (C) best align with the installation location. Mark the location of the 2 holes, and remove the hardscape adaptor (C) from the surface. □ At those marks, use a 7/32 in. drill bit to drill two 30 mm.
PAGE 3
5 □ □ □ □ □ several deck lights without hardscape 6 Connecting adaptor Connecting several deck lights with hardscape adaptor Use a Philips screwdriver to unscrew the screw connecting the foot base (1) at the opposite end of the deck light (A) where the male plug (B) is located. Twist off the foot base (1) from the deck light (A). Remove the plastic plug (2). Replace the foot base (1) and rescrew it into place. Repeat for all deck lights (A).
PAGE 4
7 □ 8 Installing into a wall When the wall is being built, the hardscape adaptor (C) can be built into the wall as illustrated below. Connecting the wires WARNING: The wire connector (D) contacts have sharp edges for piercing the main low voltage cable. To avoid injury, do not touch the metal contacts. CAUTION: The wire from low voltage power unit should be 12-16 AWG type underground low Energy Circuit Cable.
PAGE 5
□ Clean the fixture with a soft dry cloth. Problem The fixture will not light. Possible Cause □ □ □ There is no power. There is a disconnection or break in the wire. The transformer setting is incorrect. □ Do not use any cleaners with chemicals, solvents or harsh abrasives. Solution □ Check the outlet and ensure that a breaker or GFCI circuit has not been tripped. □ Follow the wires from the fixture and ensure a continuous connected path back to the transformer.