Instructions / Assembly

ManualsBrandsHampton Bay ManualsLandscape LightingSmall 25-Watt Equivalent Low Voltage Matte Black LED Outdoor Landscape Path Light with Hardscape Adapter

Table Of Contents

Use and Care Guide

LOW VOLTAGE LED DECK LIGHT

WITH HARDSCAPE ADAPTOR

PACKAGE CONTENTS

A – Deck Light x 1 C– Hardscape Adaptor x 1 D – Wire Connector (with 12 in. wire) x 1 AA – Self-Threading BB – Plastic Anchor

B – Male Plug x 1 (with 36 in. wire) E –Female Plug x 1 Screw (30 mm) x 2 (25 mm) x 2

Assembly and Installation

Preparing for installation

Installing a single deck light (without the

hardscape adaptor) on a wood surface

□ Out of the box, the male plug (B) is routed through the side of the deck

light (A). To use the male plug (B) this way, skip this Step 1. To use the

male plug (B) through the front or rear of the deck light (A), do the

following:

□ Use a Philips screwdriver (sold separately) to unscrew the screw

connecting the foot base (1) at the end of the deck light (A) where the

male plug (B) is located.

□ Twist off the foot base (1) from the deck light (A).

□ Depending on your installation, route the male plug (B) through the rear

or the front groove of the foot base (1).

□ After routing the male plug (B), twist the foot base (1) back onto the

deck light (A). Use a Philips screwdriver to reconnect the screw at the

foot base (1) to the deck light (A).

NOTE: The deck light (A) comes pre-attached to the hardscape adaptor

(C). To use the deck light (A) without the hardscape adapter (C), use a

Philips screwdriver to unscrew the 2 screws connecting the hardscape

adaptor (C) to the deck light (A).

NOTE

: Light projection can be adjusted by twisting the deck light (A) up

or down 90 degrees.

Deck light with wire behind the mounting surface:

□ Use at least a 7/16 in. drill bit to drill a hole on the mounting

surface large enough for the male plug (B) to pass through the

hole on the mounting surface.

□ Insert the male plug (B) through the hole on the mounting

surface.

□ Place the deck light (A) against the mounting surface.

□ Use a Phillips screwdriver to screw the self-threading screws

(AA) through the two holes on the deck light (A) to secure the

deck light (A) to the mounting surface.

□ Insert the male plug (B) into the female plug (E).

□ Proceed to Step 6 if installing multiple lights, or Step 8.

Deck light with wire in front of or beside the mounting

surface:

□ Place the deck light (A) on the surface where you want it to be

installed.

□ Use a Phillips screwdriver to screw the self-threading screws

(AA) through the two holes on the deck light (A) to the mounting

surface.

□ Insert the male plug (B) into the female plug (E).

□ Proceed to Step 6 if installing multiple lights, or Step 8.

Item # 1007 891 893

Model # KJC2601LM-01

Summary of content (11 pages)

PAGE 1
Item # 1007 891 893 Model # KJC2601LM-01 Use and Care Guide LOW VOLTAGE LED DECK LIGHT WITH HARDSCAPE ADAPTOR PACKAGE CONTENTS A – Deck Light x 1 C– Hardscape Adaptor x 1 B – Male Plug x 1 (with 36 in. wire) D – Wire Connector (with 12 in.
PAGE 2
Assembly and Installation (continued) 3 Installing a single deck light (with or without the hardscape adaptor) on concrete, brick, or other nonwood surface 4 Deck light with hardscape adaptor: □ Place the hardscape adaptor (C) on the surface where you want it to be installed, and choose which two holes on the hardscape adaptor (C) best align with the installation location. Mark the location of the 2 holes, and remove the hardscape adaptor (C) from the surface. □ At those marks, use a 7/32 in.
PAGE 3
Assembly and Installation (continued) 5 □ □ □ □ □ Connecting several deck lights with hardscape adaptor Connecting several deck lights without hardscape 6 adaptor Use a Philips screwdriver to unscrew the screw connecting the foot base (1) at the opposite end of the deck light (A) where the male plug (B) is located. Twist off the foot base (1) from the deck light (A). Remove the plastic plug (2). Replace the foot base (1) and rescrew it into place. Repeat for all deck lights (A).
PAGE 4
Assembly and Installation (continued) 7 □ 8 Installing into a wall When the wall is being built, the hardscape adaptor (C) can be built into the wall as illustrated below. Connecting the wires WARNING: The wire connector (D) contacts have sharp edges for piercing the main low voltage cable. To avoid injury, do not touch the metal contacts. CAUTION: The wire from low voltage power unit should be 12-16 AWG type underground low Energy Circuit Cable.
PAGE 5
Care and Cleaning □ Clean the fixture with a soft dry cloth. □ Do not use any cleaners with chemicals, solvents or harsh abrasives. Troubleshooting Problem Possible Cause Solution The fixture will not light. □ □ There is no power. There is a disconnection or break in the wire. The transformer setting is incorrect. □ Check the outlet and ensure that a breaker or GFCI circuit has not been tripped. □ Follow the wires from the fixture and ensure a continuous connected path back to the transformer.
PAGE 6
Artículo #1007 891 893 Modelo #KJC2601LM-01 GUÍA DE USO Y MANTENIMIENTO LUZ DE CUBIERTA LED DE BAJO VOLTAJE CON ADAPTADOR HARDSCAPE CONTENIDO DEL PAQUETE A –Luz de Cubierta x1 B –Enchufe Macho (con un (cable de 36 pulgadas) x1 C–Adaptador de Hardscape x 1 D –Conector Cable (con un cable de 12 pulgadas) x1 E- Enchufe Hembra x 1 AA– Tornillos Autorroscantes (30mm) x2 BB – Anclas de Plástico (25mm) x2 Montaje e Instalación 1 2 Preparándose para la instalación.
PAGE 7
Montaje e Instalación (continuación) 3 □ □ □ □ □ □ Instalación de una sola luz de cubierta(con o sin el adaptador de hardscape) en concreto, ladrillo u otra superficie que no sea de madera 4 luz de cubierta con adaptador de hardscape: Coloque el adaptador de hardscape (C) en la superficie donde desea instalarlo y elija qué dos orificios del adaptador de hardscape (C) se alinean mejor con la ubicación de instalación.
PAGE 8
Montaje e Instalación (continuación) 5 □ □ □ □ □ Conexión de varias luz de cubierta con adaptador de hardscape Utilice un destornillador Philips para destornillar el tornillo que conecta la base del pie (1) en el extremo opuesto de la luz de cubierta (A) donde se encuentra el enchufe macho (B). Gire la base del pie (1) de la luz de cubierta (A). Retire el tapón de plástico (2). Vuelva a colocar la base del pie (1) y vuelva a atornillarla en su lugar. Repita para todas las luz de cubierta (A).
PAGE 9
Montaje e Instalación (continuación) 7 □ 8 Instalación en una pared Cuando se está construyendo la pared, el adaptador de hardscape (C) se puede instalar en la pared como se ilustra a continuación. Conexión de los cables ADVERTENCIA: Los contactos del cable conector (D) tienen bordes filosos para atravesar el cable principal de bajo voltaje. No toque los contactos de metal para evitar lesiones.
PAGE 10
Mantenimiento y Limpieza □ Limpia la lámpara con un paño suave y seco. □ No uses limpiadores con químicos, solvents, o productos abrasivos. Solución de Problemas Problema Causa Posible Solución El accesorio no enciende. □ □ □ Verifique el tomacorriente y asegúrese que no esté apagado el interruptor o circuito GFC. □ Siga los cables desde el accesorio y asegúrese que esté en buen estado bien conectado al transformador. □ Verifique que esté bien la configuración del transformador.
PAGE 11
FCC Warning Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.